From fa9ff4b185b8f7f124c1c6686f02e690f0625287 Mon Sep 17 00:00:00 2001 From: Samuel Ortiz Date: Thu, 7 Feb 2008 00:14:49 -0800 Subject: ASIC3 driver This is a patch for the Compaq ASIC3 multi function chip, found in many PDAs (iPAQs, HTCs...). It is a simplified version of Paul Sokolovsky's first proposal [1]. With this code, it is basically a GPIO and IRQ expander. My plan is to add more features once this patch gets reviewed and accepted. [1] http://lkml.org/lkml/2007/5/1/46 Signed-off-by: Samuel Ortiz Cc: Paul Sokolovsky Cc: Ben Dooks Cc: Thomas Gleixner Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/mfd/asic3.h | 497 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 497 insertions(+) create mode 100644 include/linux/mfd/asic3.h (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/asic3.h b/include/linux/mfd/asic3.h new file mode 100644 index 00000000000..4ab2162db13 --- /dev/null +++ b/include/linux/mfd/asic3.h @@ -0,0 +1,497 @@ +/* + * include/linux/mfd/asic3.h + * + * Compaq ASIC3 headers. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Copyright 2001 Compaq Computer Corporation. + * Copyright 2007 OpendHand. + */ + +#ifndef __ASIC3_H__ +#define __ASIC3_H__ + +#include + +struct asic3 { + void __iomem *mapping; + unsigned int bus_shift; + unsigned int irq_nr; + unsigned int irq_base; + spinlock_t lock; + u16 irq_bothedge[4]; + struct device *dev; +}; + +struct asic3_platform_data { + struct { + u32 dir; + u32 init; + u32 sleep_mask; + u32 sleep_out; + u32 batt_fault_out; + u32 sleep_conf; + u32 alt_function; + } gpio_a, gpio_b, gpio_c, gpio_d; + + unsigned int bus_shift; + + unsigned int irq_base; + + struct platform_device **children; + unsigned int n_children; +}; + +int asic3_gpio_get_value(struct asic3 *asic, unsigned gpio); +void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val); + +#define ASIC3_NUM_GPIO_BANKS 4 +#define ASIC3_GPIOS_PER_BANK 16 +#define ASIC3_NUM_GPIOS 64 +#define ASIC3_NR_IRQS ASIC3_NUM_GPIOS + 6 + +#define ASIC3_GPIO_BANK_A 0 +#define ASIC3_GPIO_BANK_B 1 +#define ASIC3_GPIO_BANK_C 2 +#define ASIC3_GPIO_BANK_D 3 + +#define ASIC3_GPIO(bank, gpio) \ + ((ASIC3_GPIOS_PER_BANK * ASIC3_GPIO_BANK_##bank) + (gpio)) +#define ASIC3_GPIO_bit(gpio) (1 << (gpio & 0xf)) +/* All offsets below are specified with this address bus shift */ +#define ASIC3_DEFAULT_ADDR_SHIFT 2 + +#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_Base + ASIC3_##base##_##reg) +#define ASIC3_GPIO_OFFSET(base, reg) \ + (ASIC3_GPIO_##base##_Base + ASIC3_GPIO_##reg) + +#define ASIC3_GPIO_A_Base 0x0000 +#define ASIC3_GPIO_B_Base 0x0100 +#define ASIC3_GPIO_C_Base 0x0200 +#define ASIC3_GPIO_D_Base 0x0300 + +#define ASIC3_GPIO_Mask 0x00 /* R/W 0:don't mask */ +#define ASIC3_GPIO_Direction 0x04 /* R/W 0:input */ +#define ASIC3_GPIO_Out 0x08 /* R/W 0:output low */ +#define ASIC3_GPIO_TriggerType 0x0c /* R/W 0:level */ +#define ASIC3_GPIO_EdgeTrigger 0x10 /* R/W 0:falling */ +#define ASIC3_GPIO_LevelTrigger 0x14 /* R/W 0:low level detect */ +#define ASIC3_GPIO_SleepMask 0x18 /* R/W 0:don't mask in sleep mode */ +#define ASIC3_GPIO_SleepOut 0x1c /* R/W level 0:low in sleep mode */ +#define ASIC3_GPIO_BattFaultOut 0x20 /* R/W level 0:low in batt_fault */ +#define ASIC3_GPIO_IntStatus 0x24 /* R/W 0:none, 1:detect */ +#define ASIC3_GPIO_AltFunction 0x28 /* R/W 1:LED register control */ +#define ASIC3_GPIO_SleepConf 0x2c /* + * R/W bit 1: autosleep + * 0: disable gposlpout in normal mode, + * enable gposlpout in sleep mode. + */ +#define ASIC3_GPIO_Status 0x30 /* R Pin status */ + +#define ASIC3_SPI_Base 0x0400 +#define ASIC3_SPI_Control 0x0000 +#define ASIC3_SPI_TxData 0x0004 +#define ASIC3_SPI_RxData 0x0008 +#define ASIC3_SPI_Int 0x000c +#define ASIC3_SPI_Status 0x0010 + +#define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */ + +#define ASIC3_PWM_0_Base 0x0500 +#define ASIC3_PWM_1_Base 0x0600 +#define ASIC3_PWM_TimeBase 0x0000 +#define ASIC3_PWM_PeriodTime 0x0004 +#define ASIC3_PWM_DutyTime 0x0008 + +#define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */ +#define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */ + +#define ASIC3_LED_0_Base 0x0700 +#define ASIC3_LED_1_Base 0x0800 +#define ASIC3_LED_2_Base 0x0900 +#define ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */ +#define ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */ +#define ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */ +#define ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */ + +/* LED TimeBase bits - match ASIC2 */ +#define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */ + /* Note: max = 5 on hx4700 */ + /* 0: maximum time base */ + /* 1: maximum time base / 2 */ + /* n: maximum time base / 2^n */ + +#define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */ +#define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */ +#define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */ + +#define ASIC3_CLOCK_Base 0x0A00 +#define ASIC3_CLOCK_CDEX 0x00 +#define ASIC3_CLOCK_SEL 0x04 + +#define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */ +#define CLOCK_CDEX_SOURCE0 (1 << 0) +#define CLOCK_CDEX_SOURCE1 (1 << 1) +#define CLOCK_CDEX_SPI (1 << 2) +#define CLOCK_CDEX_OWM (1 << 3) +#define CLOCK_CDEX_PWM0 (1 << 4) +#define CLOCK_CDEX_PWM1 (1 << 5) +#define CLOCK_CDEX_LED0 (1 << 6) +#define CLOCK_CDEX_LED1 (1 << 7) +#define CLOCK_CDEX_LED2 (1 << 8) + +/* Clocks settings: 1 for 24.576 MHz, 0 for 12.288Mhz */ +#define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source */ +#define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source ctrl */ +#define CLOCK_CDEX_SMBUS (1 << 11) +#define CLOCK_CDEX_CONTROL_CX (1 << 12) + +#define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */ +#define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */ + +#define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select */ +#define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select */ + +/* R/W: INT clock source control (32.768 kHz) */ +#define CLOCK_SEL_CX (1 << 2) + + +#define ASIC3_INTR_Base 0x0B00 + +#define ASIC3_INTR_IntMask 0x00 /* Interrupt mask control */ +#define ASIC3_INTR_PIntStat 0x04 /* Peripheral interrupt status */ +#define ASIC3_INTR_IntCPS 0x08 /* Interrupt timer clock pre-scale */ +#define ASIC3_INTR_IntTBS 0x0c /* Interrupt timer set */ + +#define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */ +#define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */ +#define ASIC3_INTMASK_MASK0 (1 << 2) +#define ASIC3_INTMASK_MASK1 (1 << 3) +#define ASIC3_INTMASK_MASK2 (1 << 4) +#define ASIC3_INTMASK_MASK3 (1 << 5) +#define ASIC3_INTMASK_MASK4 (1 << 6) +#define ASIC3_INTMASK_MASK5 (1 << 7) + +#define ASIC3_INTR_PERIPHERAL_A (1 << 0) +#define ASIC3_INTR_PERIPHERAL_B (1 << 1) +#define ASIC3_INTR_PERIPHERAL_C (1 << 2) +#define ASIC3_INTR_PERIPHERAL_D (1 << 3) +#define ASIC3_INTR_LED0 (1 << 4) +#define ASIC3_INTR_LED1 (1 << 5) +#define ASIC3_INTR_LED2 (1 << 6) +#define ASIC3_INTR_SPI (1 << 7) +#define ASIC3_INTR_SMBUS (1 << 8) +#define ASIC3_INTR_OWM (1 << 9) + +#define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */ +#define ASIC3_INTR_CPS_SET (1 << 4) /* Time base enable */ + + +/* Basic control of the SD ASIC */ +#define ASIC3_SDHWCTRL_Base 0x0E00 +#define ASIC3_SDHWCTRL_SDConf 0x00 + +#define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */ +#define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */ +#define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */ +#define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* SD card detection: 0:low */ + +/* SD card write protection: 0=high */ +#define ASIC3_SDHWCTRL_LEVWP (1 << 4) +#define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 0=disable */ + +/* SD card power supply ctrl 1=enable */ +#define ASIC3_SDHWCTRL_SDPWR (1 << 6) + +#define ASIC3_EXTCF_Base 0x1100 + +#define ASIC3_EXTCF_Select 0x00 +#define ASIC3_EXTCF_Reset 0x04 + +#define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */ +#define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */ +#define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */ +#define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */ +#define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */ +#define ASIC3_EXTCF_OWM_RESET (1 << 6) /* ?? used by OWM and CF */ +#define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state */ +#define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state */ +#define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */ +#define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */ +#define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */ +#define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */ +#define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14) +#define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */ + +/********************************************* + * The Onewire interface registers + * + * OWM_CMD + * OWM_DAT + * OWM_INTR + * OWM_INTEN + * OWM_CLKDIV + * + *********************************************/ + +#define ASIC3_OWM_Base 0xC00 + +#define ASIC3_OWM_CMD 0x00 +#define ASIC3_OWM_DAT 0x04 +#define ASIC3_OWM_INTR 0x08 +#define ASIC3_OWM_INTEN 0x0C +#define ASIC3_OWM_CLKDIV 0x10 + +#define ASIC3_OWM_CMD_ONEWR (1 << 0) +#define ASIC3_OWM_CMD_SRA (1 << 1) +#define ASIC3_OWM_CMD_DQO (1 << 2) +#define ASIC3_OWM_CMD_DQI (1 << 3) + +#define ASIC3_OWM_INTR_PD (1 << 0) +#define ASIC3_OWM_INTR_PDR (1 << 1) +#define ASIC3_OWM_INTR_TBE (1 << 2) +#define ASIC3_OWM_INTR_TEMP (1 << 3) +#define ASIC3_OWM_INTR_RBF (1 << 4) + +#define ASIC3_OWM_INTEN_EPD (1 << 0) +#define ASIC3_OWM_INTEN_IAS (1 << 1) +#define ASIC3_OWM_INTEN_ETBE (1 << 2) +#define ASIC3_OWM_INTEN_ETMT (1 << 3) +#define ASIC3_OWM_INTEN_ERBF (1 << 4) + +#define ASIC3_OWM_CLKDIV_PRE (3 << 0) /* two bits wide at bit 0 */ +#define ASIC3_OWM_CLKDIV_DIV (7 << 2) /* 3 bits wide at bit 2 */ + + +/***************************************************************************** + * The SD configuration registers are at a completely different location + * in memory. They are divided into three sets of registers: + * + * SD_CONFIG Core configuration register + * SD_CTRL Control registers for SD operations + * SDIO_CTRL Control registers for SDIO operations + * + *****************************************************************************/ +#define ASIC3_SD_CONFIG_Base 0x0400 /* Assumes 32 bit addressing */ + +#define ASIC3_SD_CONFIG_Command 0x08 /* R/W: Command */ + +/* [0:8] SD Control Register Base Address */ +#define ASIC3_SD_CONFIG_Addr0 0x20 + +/* [9:31] SD Control Register Base Address */ +#define ASIC3_SD_CONFIG_Addr1 0x24 + +/* R/O: interrupt assigned to pin */ +#define ASIC3_SD_CONFIG_IntPin 0x78 + +/* + * Set to 0x1f to clock SD controller, 0 otherwise. + * At 0x82 - Gated Clock Ctrl + */ +#define ASIC3_SD_CONFIG_ClkStop 0x80 + +/* Control clock of SD controller */ +#define ASIC3_SD_CONFIG_ClockMode 0x84 +#define ASIC3_SD_CONFIG_SDHC_PinStatus 0x88 /* R/0: SD pins status */ +#define ASIC3_SD_CONFIG_SDHC_Power1 0x90 /* Power1 - manual pwr ctrl */ + +/* auto power up after card inserted */ +#define ASIC3_SD_CONFIG_SDHC_Power2 0x92 + +/* auto power down when card removed */ +#define ASIC3_SD_CONFIG_SDHC_Power3 0x94 +#define ASIC3_SD_CONFIG_SDHC_CardDetect 0x98 +#define ASIC3_SD_CONFIG_SDHC_Slot 0xA0 /* R/O: support slot number */ +#define ASIC3_SD_CONFIG_SDHC_ExtGateClk1 0x1E0 /* Not used */ +#define ASIC3_SD_CONFIG_SDHC_ExtGateClk2 0x1E2 /* Not used*/ + +/* GPIO Output Reg. , at 0x1EA - GPIO Output Enable Reg. */ +#define ASIC3_SD_CONFIG_SDHC_GPIO_OutAndEnable 0x1E8 +#define ASIC3_SD_CONFIG_SDHC_GPIO_Status 0x1EC /* GPIO Status Reg. */ + +/* Bit 1: double buffer/single buffer */ +#define ASIC3_SD_CONFIG_SDHC_ExtGateClk3 0x1F0 + +/* Memory access enable (set to 1 to access SD Controller) */ +#define SD_CONFIG_COMMAND_MAE (1<<1) + +#define SD_CONFIG_CLK_ENABLE_ALL 0x1f + +#define SD_CONFIG_POWER1_PC_33V 0x0200 /* Set for 3.3 volts */ +#define SD_CONFIG_POWER1_PC_OFF 0x0000 /* Turn off power */ + + /* two bits - number of cycles for card detection */ +#define SD_CONFIG_CARDDETECTMODE_CLK ((x) & 0x3) + + +#define ASIC3_SD_CTRL_Base 0x1000 + +#define ASIC3_SD_CTRL_Cmd 0x00 +#define ASIC3_SD_CTRL_Arg0 0x08 +#define ASIC3_SD_CTRL_Arg1 0x0C +#define ASIC3_SD_CTRL_StopInternal 0x10 +#define ASIC3_SD_CTRL_TransferSectorCount 0x14 +#define ASIC3_SD_CTRL_Response0 0x18 +#define ASIC3_SD_CTRL_Response1 0x1C +#define ASIC3_SD_CTRL_Response2 0x20 +#define ASIC3_SD_CTRL_Response3 0x24 +#define ASIC3_SD_CTRL_Response4 0x28 +#define ASIC3_SD_CTRL_Response5 0x2C +#define ASIC3_SD_CTRL_Response6 0x30 +#define ASIC3_SD_CTRL_Response7 0x34 +#define ASIC3_SD_CTRL_CardStatus 0x38 +#define ASIC3_SD_CTRL_BufferCtrl 0x3C +#define ASIC3_SD_CTRL_IntMaskCard 0x40 +#define ASIC3_SD_CTRL_IntMaskBuffer 0x44 +#define ASIC3_SD_CTRL_CardClockCtrl 0x48 +#define ASIC3_SD_CTRL_MemCardXferDataLen 0x4C +#define ASIC3_SD_CTRL_MemCardOptionSetup 0x50 +#define ASIC3_SD_CTRL_ErrorStatus0 0x58 +#define ASIC3_SD_CTRL_ErrorStatus1 0x5C +#define ASIC3_SD_CTRL_DataPort 0x60 +#define ASIC3_SD_CTRL_TransactionCtrl 0x68 +#define ASIC3_SD_CTRL_SoftwareReset 0x1C0 + +#define SD_CTRL_SOFTWARE_RESET_CLEAR (1<<0) + +#define SD_CTRL_TRANSACTIONCONTROL_SET (1<<8) + +#define SD_CTRL_CARDCLOCKCONTROL_FOR_SD_CARD (1<<15) +#define SD_CTRL_CARDCLOCKCONTROL_ENABLE_CLOCK (1<<8) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_512 (1<<7) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_256 (1<<6) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_128 (1<<5) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_64 (1<<4) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_32 (1<<3) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_16 (1<<2) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_8 (1<<1) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_4 (1<<0) +#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_2 (0<<0) + +#define MEM_CARD_OPTION_REQUIRED 0x000e +#define MEM_CARD_OPTION_DATA_RESPONSE_TIMEOUT(x) (((x) & 0x0f) << 4) +#define MEM_CARD_OPTION_C2_MODULE_NOT_PRESENT (1<<14) +#define MEM_CARD_OPTION_DATA_XFR_WIDTH_1 (1<<15) +#define MEM_CARD_OPTION_DATA_XFR_WIDTH_4 0 + +#define SD_CTRL_COMMAND_INDEX(x) ((x) & 0x3f) +#define SD_CTRL_COMMAND_TYPE_CMD (0 << 6) +#define SD_CTRL_COMMAND_TYPE_ACMD (1 << 6) +#define SD_CTRL_COMMAND_TYPE_AUTHENTICATION (2 << 6) +#define SD_CTRL_COMMAND_RESPONSE_TYPE_NORMAL (0 << 8) +#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1 (4 << 8) +#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1B (5 << 8) +#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R2 (6 << 8) +#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R3 (7 << 8) +#define SD_CTRL_COMMAND_DATA_PRESENT (1 << 11) +#define SD_CTRL_COMMAND_TRANSFER_READ (1 << 12) +#define SD_CTRL_COMMAND_TRANSFER_WRITE (0 << 12) +#define SD_CTRL_COMMAND_MULTI_BLOCK (1 << 13) +#define SD_CTRL_COMMAND_SECURITY_CMD (1 << 14) + +#define SD_CTRL_STOP_INTERNAL_ISSSUE_CMD12 (1 << 0) +#define SD_CTRL_STOP_INTERNAL_AUTO_ISSUE_CMD12 (1 << 8) + +#define SD_CTRL_CARDSTATUS_RESPONSE_END (1 << 0) +#define SD_CTRL_CARDSTATUS_RW_END (1 << 2) +#define SD_CTRL_CARDSTATUS_CARD_REMOVED_0 (1 << 3) +#define SD_CTRL_CARDSTATUS_CARD_INSERTED_0 (1 << 4) +#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_0 (1 << 5) +#define SD_CTRL_CARDSTATUS_WRITE_PROTECT (1 << 7) +#define SD_CTRL_CARDSTATUS_CARD_REMOVED_3 (1 << 8) +#define SD_CTRL_CARDSTATUS_CARD_INSERTED_3 (1 << 9) +#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_3 (1 << 10) + +#define SD_CTRL_BUFFERSTATUS_CMD_INDEX_ERROR (1 << 0) +#define SD_CTRL_BUFFERSTATUS_CRC_ERROR (1 << 1) +#define SD_CTRL_BUFFERSTATUS_STOP_BIT_END_ERROR (1 << 2) +#define SD_CTRL_BUFFERSTATUS_DATA_TIMEOUT (1 << 3) +#define SD_CTRL_BUFFERSTATUS_BUFFER_OVERFLOW (1 << 4) +#define SD_CTRL_BUFFERSTATUS_BUFFER_UNDERFLOW (1 << 5) +#define SD_CTRL_BUFFERSTATUS_CMD_TIMEOUT (1 << 6) +#define SD_CTRL_BUFFERSTATUS_UNK7 (1 << 7) +#define SD_CTRL_BUFFERSTATUS_BUFFER_READ_ENABLE (1 << 8) +#define SD_CTRL_BUFFERSTATUS_BUFFER_WRITE_ENABLE (1 << 9) +#define SD_CTRL_BUFFERSTATUS_ILLEGAL_FUNCTION (1 << 13) +#define SD_CTRL_BUFFERSTATUS_CMD_BUSY (1 << 14) +#define SD_CTRL_BUFFERSTATUS_ILLEGAL_ACCESS (1 << 15) + +#define SD_CTRL_INTMASKCARD_RESPONSE_END (1 << 0) +#define SD_CTRL_INTMASKCARD_RW_END (1 << 2) +#define SD_CTRL_INTMASKCARD_CARD_REMOVED_0 (1 << 3) +#define SD_CTRL_INTMASKCARD_CARD_INSERTED_0 (1 << 4) +#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_0 (1 << 5) +#define SD_CTRL_INTMASKCARD_UNK6 (1 << 6) +#define SD_CTRL_INTMASKCARD_WRITE_PROTECT (1 << 7) +#define SD_CTRL_INTMASKCARD_CARD_REMOVED_3 (1 << 8) +#define SD_CTRL_INTMASKCARD_CARD_INSERTED_3 (1 << 9) +#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_3 (1 << 10) + +#define SD_CTRL_INTMASKBUFFER_CMD_INDEX_ERROR (1 << 0) +#define SD_CTRL_INTMASKBUFFER_CRC_ERROR (1 << 1) +#define SD_CTRL_INTMASKBUFFER_STOP_BIT_END_ERROR (1 << 2) +#define SD_CTRL_INTMASKBUFFER_DATA_TIMEOUT (1 << 3) +#define SD_CTRL_INTMASKBUFFER_BUFFER_OVERFLOW (1 << 4) +#define SD_CTRL_INTMASKBUFFER_BUFFER_UNDERFLOW (1 << 5) +#define SD_CTRL_INTMASKBUFFER_CMD_TIMEOUT (1 << 6) +#define SD_CTRL_INTMASKBUFFER_UNK7 (1 << 7) +#define SD_CTRL_INTMASKBUFFER_BUFFER_READ_ENABLE (1 << 8) +#define SD_CTRL_INTMASKBUFFER_BUFFER_WRITE_ENABLE (1 << 9) +#define SD_CTRL_INTMASKBUFFER_ILLEGAL_FUNCTION (1 << 13) +#define SD_CTRL_INTMASKBUFFER_CMD_BUSY (1 << 14) +#define SD_CTRL_INTMASKBUFFER_ILLEGAL_ACCESS (1 << 15) + +#define SD_CTRL_DETAIL0_RESPONSE_CMD_ERROR (1 << 0) +#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 2) +#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_CMD12 (1 << 3) +#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_READ_DATA (1 << 4) +#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_WRITE_CRC_STATUS (1 << 5) +#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 8) +#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_CMD12 (1 << 9) +#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_READ_DATA (1 << 10) +#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_WRITE_CMD (1 << 11) + +#define SD_CTRL_DETAIL1_NO_CMD_RESPONSE (1 << 0) +#define SD_CTRL_DETAIL1_TIMEOUT_READ_DATA (1 << 4) +#define SD_CTRL_DETAIL1_TIMEOUT_CRS_STATUS (1 << 5) +#define SD_CTRL_DETAIL1_TIMEOUT_CRC_BUSY (1 << 6) + +#define ASIC3_SDIO_CTRL_Base 0x1200 + +#define ASIC3_SDIO_CTRL_Cmd 0x00 +#define ASIC3_SDIO_CTRL_CardPortSel 0x04 +#define ASIC3_SDIO_CTRL_Arg0 0x08 +#define ASIC3_SDIO_CTRL_Arg1 0x0C +#define ASIC3_SDIO_CTRL_TransferBlockCount 0x14 +#define ASIC3_SDIO_CTRL_Response0 0x18 +#define ASIC3_SDIO_CTRL_Response1 0x1C +#define ASIC3_SDIO_CTRL_Response2 0x20 +#define ASIC3_SDIO_CTRL_Response3 0x24 +#define ASIC3_SDIO_CTRL_Response4 0x28 +#define ASIC3_SDIO_CTRL_Response5 0x2C +#define ASIC3_SDIO_CTRL_Response6 0x30 +#define ASIC3_SDIO_CTRL_Response7 0x34 +#define ASIC3_SDIO_CTRL_CardStatus 0x38 +#define ASIC3_SDIO_CTRL_BufferCtrl 0x3C +#define ASIC3_SDIO_CTRL_IntMaskCard 0x40 +#define ASIC3_SDIO_CTRL_IntMaskBuffer 0x44 +#define ASIC3_SDIO_CTRL_CardXferDataLen 0x4C +#define ASIC3_SDIO_CTRL_CardOptionSetup 0x50 +#define ASIC3_SDIO_CTRL_ErrorStatus0 0x54 +#define ASIC3_SDIO_CTRL_ErrorStatus1 0x58 +#define ASIC3_SDIO_CTRL_DataPort 0x60 +#define ASIC3_SDIO_CTRL_TransactionCtrl 0x68 +#define ASIC3_SDIO_CTRL_CardIntCtrl 0x6C +#define ASIC3_SDIO_CTRL_ClocknWaitCtrl 0x70 +#define ASIC3_SDIO_CTRL_HostInformation 0x74 +#define ASIC3_SDIO_CTRL_ErrorCtrl 0x78 +#define ASIC3_SDIO_CTRL_LEDCtrl 0x7C +#define ASIC3_SDIO_CTRL_SoftwareReset 0x1C0 + +#define ASIC3_MAP_SIZE 0x2000 + +#endif /* __ASIC3_H__ */ -- cgit v1.2.3