From 0931a4c6dbfab03f2bfd22a9170130f7b155d53a Mon Sep 17 00:00:00 2001 From: David Brownell Date: Mon, 22 Dec 2008 12:05:27 +0100 Subject: mfd: dm355evm msp430 driver Basic MFD framework for the MSP430 microcontroller firmware used on the dm355evm board: - Provides an interface for other drivers: register read/write utilities, and register declarations. - Directly exports: * Many signals through the GPIO framework + LEDs + SW6 through gpio sysfs + NTSC/nPAL jumper through gpio sysfs + ... more could be added later, e.g. MMC signals * Child devices: + LEDs, via leds-gpio child (and default triggers) + RTC, via rtc-dm355evm child device + Buttons and IR control, via dm355evm_keys - Supports power-off system call. Use the reset button to power the board back up; the power supply LED will be on, but the MSP430 waits to re-activate the regulators. - On probe() this: * Announces firmware revision * Turns off the banked LEDs * Exports the resources noted above * Hooks the power-off support * Muxes tvp5146 -or- imager for video input Unless the new tvp514x driver (tracked for mainline) is configured, this assumes that some custom imager driver handles video-in. This completely ignores the registers reporting the output voltages on the various power supplies. Someone could add a hwmon interface if that seems useful. Signed-off-by: David Brownell Signed-off-by: Samuel Ortiz --- include/linux/i2c/dm355evm_msp.h | 79 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 79 insertions(+) create mode 100644 include/linux/i2c/dm355evm_msp.h (limited to 'include') diff --git a/include/linux/i2c/dm355evm_msp.h b/include/linux/i2c/dm355evm_msp.h new file mode 100644 index 00000000000..372470350fa --- /dev/null +++ b/include/linux/i2c/dm355evm_msp.h @@ -0,0 +1,79 @@ +/* + * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board + */ +#ifndef __LINUX_I2C_DM355EVM_MSP +#define __LINUX_I2C_DM355EVM_MSP + +/* + * Written against Spectrum's writeup for the A4 firmware revision, + * and tweaked to match source and rev D2 schematics by removing CPLD + * and NOR flash hooks (which were last appropriate in rev B boards). + * + * Note that the firmware supports a flavor of write posting ... to be + * sure a write completes, issue another read or write. + */ + +/* utilities to access "registers" emulated by msp430 firmware */ +extern int dm355evm_msp_write(u8 value, u8 reg); +extern int dm355evm_msp_read(u8 reg); + + +/* command/control registers */ +#define DM355EVM_MSP_COMMAND 0x00 +# define MSP_COMMAND_NULL 0 +# define MSP_COMMAND_RESET_COLD 1 +# define MSP_COMMAND_RESET_WARM 2 +# define MSP_COMMAND_RESET_WARM_I 3 +# define MSP_COMMAND_POWEROFF 4 +# define MSP_COMMAND_IR_REINIT 5 +#define DM355EVM_MSP_STATUS 0x01 +# define MSP_STATUS_BAD_OFFSET BIT(0) +# define MSP_STATUS_BAD_COMMAND BIT(1) +# define MSP_STATUS_POWER_ERROR BIT(2) +# define MSP_STATUS_RXBUF_OVERRUN BIT(3) +#define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */ +# define MSP_RESET_DC5 BIT(0) +# define MSP_RESET_TVP5154 BIT(2) +# define MSP_RESET_IMAGER BIT(3) +# define MSP_RESET_ETHERNET BIT(4) +# define MSP_RESET_SYS BIT(5) +# define MSP_RESET_AIC33 BIT(7) + +/* GPIO registers ... bit patterns mostly match the source MSP ports */ +#define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */ +#define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */ +# define MSP_SWITCH1_SW6_1 BIT(0) +# define MSP_SWITCH1_SW6_2 BIT(1) +# define MSP_SWITCH1_SW6_3 BIT(2) +# define MSP_SWITCH1_SW6_4 BIT(3) +# define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */ +# define MSP_SWITCH1_MSP_INT BIT(5) /* active low */ +#define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */ +# define MSP_SWITCH2_SW10 BIT(3) +# define MSP_SWITCH2_SW11 BIT(4) +# define MSP_SWITCH2_SW12 BIT(5) +# define MSP_SWITCH2_SW13 BIT(6) +# define MSP_SWITCH2_SW14 BIT(7) +#define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */ +# define MSP_SDMMC_0_WP BIT(1) +# define MSP_SDMMC_0_CD BIT(2) /* active low */ +# define MSP_SDMMC_1_WP BIT(3) +# define MSP_SDMMC_1_CD BIT(4) /* active low */ +#define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */ +#define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */ +# define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */ + +/* power supply registers are currently omitted */ + +/* RTC registers */ +#define DM355EVM_MSP_RTC_0 0x12 /* LSB */ +#define DM355EVM_MSP_RTC_1 0x13 +#define DM355EVM_MSP_RTC_2 0x14 +#define DM355EVM_MSP_RTC_3 0x15 /* MSB */ + +/* input event queue registers; code == ((HIGH << 8) | LOW) */ +#define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */ +#define DM355EVM_MSP_INPUT_HIGH 0x17 +#define DM355EVM_MSP_INPUT_LOW 0x18 + +#endif /* __LINUX_I2C_DM355EVM_MSP */ -- cgit v1.2.3