/* * linux/drivers/clocksource/acpi_pm.c * * This file contains the ACPI PM based clocksource. * * This code was largely moved from the i386 timer_pm.c file * which was (C) Dominik Brodowski <linux@brodo.de> 2003 * and contained the following comments: * * Driver to use the Power Management Timer (PMTMR) available in some * southbridges as primary timing source for the Linux kernel. * * Based on parts of linux/drivers/acpi/hardware/hwtimer.c, timer_pit.c, * timer_hpet.c, and on Arjan van de Ven's implementation for 2.4. * * This file is licensed under the GPL v2. */ #include <linux/clocksource.h> #include <linux/errno.h> #include <linux/init.h> #include <linux/pci.h> #include <asm/io.h> /* Number of PMTMR ticks expected during calibration run */ #define PMTMR_TICKS_PER_SEC 3579545 /* * The I/O port the PMTMR resides at. * The location is detected during setup_arch(), * in arch/i386/acpi/boot.c */ u32 pmtmr_ioport __read_mostly; #define ACPI_PM_MASK CLOCKSOURCE_MASK(24) /* limit it to 24 bits */ static inline u32 read_pmtmr(void) { /* mask the output to 24 bits */ return inl(pmtmr_ioport) & ACPI_PM_MASK; } static cycle_t acpi_pm_read_verified(void) { u32 v1 = 0, v2 = 0, v3 = 0; /* * It has been reported that because of various broken * chipsets (ICH4, PIIX4 and PIIX4E) where the ACPI PM clock * source is not latched, you must read it multiple * times to ensure a safe value is read: */ do { v1 = read_pmtmr(); v2 = read_pmtmr(); v3 = read_pmtmr(); } while (unlikely((v1 > v2 && v1 < v3) || (v2 > v3 && v2 < v1) || (v3 > v1 && v3 < v2))); return (cycle_t)v2; } static cycle_t acpi_pm_read(void) { return (cycle_t)read_pmtmr(); } static struct clocksource clocksource_acpi_pm = { .name = "acpi_pm", .rating = 200, .read = acpi_pm_read, .mask = (cycle_t)ACPI_PM_MASK, .mult = 0, /*to be caluclated*/ .shift = 22, .is_continuous = 1, }; #ifdef CONFIG_PCI static int acpi_pm_good; static int __init acpi_pm_good_setup(char *__str) { acpi_pm_good = 1; return 1; } __setup("acpi_pm_good", acpi_pm_good_setup); static inline void acpi_pm_need_workaround(void) { clocksource_acpi_pm.read = acpi_pm_read_verified; clocksource_acpi_pm.rating = 110; } /* * PIIX4 Errata: * * The power management timer may return improper results when read. * Although the timer value settles properly after incrementing, * while incrementing there is a 3 ns window every 69.8 ns where the * timer value is indeterminate (a 4.2% chance that the data will be * incorrect when read). As a result, the ACPI free running count up * timer specification is violated due to erroneous reads. */ static void __devinit acpi_pm_check_blacklist(struct pci_dev *dev) { u8 rev; if (acpi_pm_good) return; pci_read_config_byte(dev, PCI_REVISION_ID, &rev); /* the bug has been fixed in PIIX4M */ if (rev < 3) { printk(KERN_WARNING "* Found PM-Timer Bug on the chipset." " Due to workarounds for a bug,\n" "* this clock source is slow. Consider trying" " other clock sources\n"); acpi_pm_need_workaround(); } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, acpi_pm_check_blacklist); static void __devinit acpi_pm_check_graylist(struct pci_dev *dev) { if (acpi_pm_good) return; printk(KERN_WARNING "* The chipset may have PM-Timer Bug. Due to" " workarounds for a bug,\n" "* this clock source is slow. If you are sure your timer" " does not have\n" "* this bug, please use \"acpi_pm_good\" to disable the" " workaround\n"); acpi_pm_need_workaround(); } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, acpi_pm_check_graylist); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_LE, acpi_pm_check_graylist); #endif #ifndef CONFIG_X86_64 #include "mach_timer.h" #define PMTMR_EXPECTED_RATE \ ((CALIBRATE_LATCH * (PMTMR_TICKS_PER_SEC >> 10)) / (CLOCK_TICK_RATE>>10)) /* * Some boards have the PMTMR running way too fast. We check * the PMTMR rate against PIT channel 2 to catch these cases. */ static int verify_pmtmr_rate(void) { u32 value1, value2; unsigned long count, delta; mach_prepare_counter(); value1 = read_pmtmr(); mach_countup(&count); value2 = read_pmtmr(); delta = (value2 - value1) & ACPI_PM_MASK; /* Check that the PMTMR delta is within 5% of what we expect */ if (delta < (PMTMR_EXPECTED_RATE * 19) / 20 || delta > (PMTMR_EXPECTED_RATE * 21) / 20) { printk(KERN_INFO "PM-Timer running at invalid rate: %lu%% " "of normal - aborting.\n", 100UL * delta / PMTMR_EXPECTED_RATE); return -1; } return 0; } #else #define verify_pmtmr_rate() (0) #endif static int __init init_acpi_pm_clocksource(void) { u32 value1, value2; unsigned int i; if (!pmtmr_ioport) return -ENODEV; clocksource_acpi_pm.mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, clocksource_acpi_pm.shift); /* "verify" this timing source: */ value1 = read_pmtmr(); for (i = 0; i < 10000; i++) { value2 = read_pmtmr(); if (value2 == value1) continue; if (value2 > value1) goto pm_good; if ((value2 < value1) && ((value2) < 0xFFF)) goto pm_good; printk(KERN_INFO "PM-Timer had inconsistent results:" " 0x%#x, 0x%#x - aborting.\n", value1, value2); return -EINVAL; } printk(KERN_INFO "PM-Timer had no reasonable result:" " 0x%#x - aborting.\n", value1); return -ENODEV; pm_good: if (verify_pmtmr_rate() != 0) return -ENODEV; return clocksource_register(&clocksource_acpi_pm); } module_init(init_acpi_pm_clocksource);