/* * drivers/net/gianfar.c * * Gianfar Ethernet Driver * This driver is designed for the non-CPM ethernet controllers * on the 85xx and 83xx family of integrated processors * Based on 8260_io/fcc_enet.c * * Author: Andy Fleming * Maintainer: Kumar Gala * * Copyright (c) 2002-2006 Freescale Semiconductor, Inc. * Copyright (c) 2007 MontaVista Software, Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. * * Gianfar: AKA Lambda Draconis, "Dragon" * RA 11 31 24.2 * Dec +69 19 52 * V 3.84 * B-V +1.62 * * Theory of operation * * The driver is initialized through of_device. Configuration information * is therefore conveyed through an OF-style device tree. * * The Gianfar Ethernet Controller uses a ring of buffer * descriptors. The beginning is indicated by a register * pointing to the physical address of the start of the ring. * The end is determined by a "wrap" bit being set in the * last descriptor of the ring. * * When a packet is received, the RXF bit in the * IEVENT register is set, triggering an interrupt when the * corresponding bit in the IMASK register is also set (if * interrupt coalescing is active, then the interrupt may not * happen immediately, but will wait until either a set number * of frames or amount of time have passed). In NAPI, the * interrupt handler will signal there is work to be done, and * exit. This method will start at the last known empty * descriptor, and process every subsequent descriptor until there * are none left with data (NAPI will stop after a set number of * packets to give time to other tasks, but will eventually * process all the packets). The data arrives inside a * pre-allocated skb, and so after the skb is passed up to the * stack, a new skb must be allocated, and the address field in * the buffer descriptor must be updated to indicate this new * skb. * * When the kernel requests that a packet be transmitted, the * driver starts where it left off last time, and points the * descriptor at the buffer which was passed in. The driver * then informs the DMA engine that there are packets ready to * be transmitted. Once the controller is finished transmitting * the packet, an interrupt may be triggered (under the same * conditions as for reception, but depending on the TXF bit). * The driver then cleans up the buffer. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "gianfar.h" #include "gianfar_mii.h" #define TX_TIMEOUT (1*HZ) #undef BRIEF_GFAR_ERRORS #undef VERBOSE_GFAR_ERRORS const char gfar_driver_name[] = "Gianfar Ethernet"; const char gfar_driver_version[] = "1.3"; static int gfar_enet_open(struct net_device *dev); static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev); static void gfar_reset_task(struct work_struct *work); static void gfar_timeout(struct net_device *dev); static int gfar_close(struct net_device *dev); struct sk_buff *gfar_new_skb(struct net_device *dev); static void gfar_new_rxbdp(struct net_device *dev, struct rxbd8 *bdp, struct sk_buff *skb); static int gfar_set_mac_address(struct net_device *dev); static int gfar_change_mtu(struct net_device *dev, int new_mtu); static irqreturn_t gfar_error(int irq, void *dev_id); static irqreturn_t gfar_transmit(int irq, void *dev_id); static irqreturn_t gfar_interrupt(int irq, void *dev_id); static void adjust_link(struct net_device *dev); static void init_registers(struct net_device *dev); static int init_phy(struct net_device *dev); static int gfar_probe(struct of_device *ofdev, const struct of_device_id *match); static int gfar_remove(struct of_device *ofdev); static void free_skb_resources(struct gfar_private *priv); static void gfar_set_multi(struct net_device *dev); static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr); static void gfar_configure_serdes(struct net_device *dev); static int gfar_poll(struct napi_struct *napi, int budget); #ifdef CONFIG_NET_POLL_CONTROLLER static void gfar_netpoll(struct net_device *dev); #endif int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit); static int gfar_clean_tx_ring(struct net_device *dev); static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int amount_pull); static void gfar_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp); void gfar_halt(struct net_device *dev); static void gfar_halt_nodisable(struct net_device *dev); void gfar_start(struct net_device *dev); static void gfar_clear_exact_match(struct net_device *dev); static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr); extern const struct ethtool_ops gfar_ethtool_ops; MODULE_AUTHOR("Freescale Semiconductor, Inc"); MODULE_DESCRIPTION("Gianfar Ethernet Driver"); MODULE_LICENSE("GPL"); /* Returns 1 if incoming frames use an FCB */ static inline int gfar_uses_fcb(struct gfar_private *priv) { return priv->vlgrp || priv->rx_csum_enable; } static int gfar_of_init(struct net_device *dev) { struct device_node *phy, *mdio; const unsigned int *id; const char *model; const char *ctype; const void *mac_addr; const phandle *ph; u64 addr, size; int err = 0; struct gfar_private *priv = netdev_priv(dev); struct device_node *np = priv->node; char bus_name[MII_BUS_ID_SIZE]; if (!np || !of_device_is_available(np)) return -ENODEV; /* get a pointer to the register memory */ addr = of_translate_address(np, of_get_address(np, 0, &size, NULL)); priv->regs = ioremap(addr, size); if (priv->regs == NULL) return -ENOMEM; priv->interruptTransmit = irq_of_parse_and_map(np, 0); model = of_get_property(np, "model", NULL); /* If we aren't the FEC we have multiple interrupts */ if (model && strcasecmp(model, "FEC")) { priv->interruptReceive = irq_of_parse_and_map(np, 1); priv->interruptError = irq_of_parse_and_map(np, 2); if (priv->interruptTransmit < 0 || priv->interruptReceive < 0 || priv->interruptError < 0) { err = -EINVAL; goto err_out; } } mac_addr = of_get_mac_address(np); if (mac_addr) memcpy(dev->dev_addr, mac_addr, MAC_ADDR_LEN); if (model && !strcasecmp(model, "TSEC")) priv->device_flags = FSL_GIANFAR_DEV_HAS_GIGABIT | FSL_GIANFAR_DEV_HAS_COALESCE | FSL_GIANFAR_DEV_HAS_RMON | FSL_GIANFAR_DEV_HAS_MULTI_INTR; if (model && !strcasecmp(model, "eTSEC")) priv->device_flags = FSL_GIANFAR_DEV_HAS_GIGABIT | FSL_GIANFAR_DEV_HAS_COALESCE | FSL_GIANFAR_DEV_HAS_RMON | FSL_GIANFAR_DEV_HAS_MULTI_INTR | FSL_GIANFAR_DEV_HAS_PADDING | FSL_GIANFAR_DEV_HAS_CSUM | FSL_GIANFAR_DEV_HAS_VLAN | FSL_GIANFAR_DEV_HAS_MAGIC_PACKET | FSL_GIANFAR_DEV_HAS_EXTENDED_HASH; ctype = of_get_property(np, "phy-connection-type", NULL); /* We only care about rgmii-id. The rest are autodetected */ if (ctype && !strcmp(ctype, "rgmii-id")) priv->interface = PHY_INTERFACE_MODE_RGMII_ID; else priv->interface = PHY_INTERFACE_MODE_MII; if (of_get_property(np, "fsl,magic-packet", NULL)) priv->device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET; ph = of_get_property(np, "phy-handle", NULL); if (ph == NULL) { u32 *fixed_link; fixed_link = (u32 *)of_get_property(np, "fixed-link", NULL); if (!fixed_link) { err = -ENODEV; goto err_out; } snprintf(priv->phy_bus_id, sizeof(priv->phy_bus_id), PHY_ID_FMT, "0", fixed_link[0]); } else { phy = of_find_node_by_phandle(*ph); if (phy == NULL) { err = -ENODEV; goto err_out; } mdio = of_get_parent(phy); id = of_get_property(phy, "reg", NULL); of_node_put(phy); of_node_put(mdio); gfar_mdio_bus_name(bus_name, mdio); snprintf(priv->phy_bus_id, sizeof(priv->phy_bus_id), "%s:%02x", bus_name, *id); } /* Find the TBI PHY. If it's not there, we don't support SGMII */ ph = of_get_property(np, "tbi-handle", NULL); if (ph) { struct device_node *tbi = of_find_node_by_phandle(*ph); struct of_device *ofdev; struct mii_bus *bus; if (!tbi) return 0; mdio = of_get_parent(tbi); if (!mdio) return 0; ofdev = of_find_device_by_node(mdio); of_node_put(mdio); id = of_get_property(tbi, "reg", NULL); if (!id) return 0; of_node_put(tbi); bus = dev_get_drvdata(&ofdev->dev); priv->tbiphy = bus->phy_map[*id]; } return 0; err_out: iounmap(priv->regs); return err; } /* Ioctl MII Interface */ static int gfar_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) { struct gfar_private *priv = netdev_priv(dev); if (!netif_running(dev)) return -EINVAL; if (!priv->phydev) return -ENODEV; return phy_mii_ioctl(priv->phydev, if_mii(rq), cmd); } /* Set up the ethernet device structure, private data, * and anything else we need before we start */ static int gfar_probe(struct of_device *ofdev, const struct of_device_id *match) { u32 tempval; struct net_device *dev = NULL; struct gfar_private *priv = NULL; DECLARE_MAC_BUF(mac); int err = 0; int len_devname; /* Create an ethernet device instance */ dev = alloc_etherdev(sizeof (*priv)); if (NULL == dev) return -ENOMEM; priv = netdev_priv(dev); priv->dev = dev; priv->node = ofdev->node; err = gfar_of_init(dev); if (err) goto regs_fail; spin_lock_init(&priv->txlock); spin_lock_init(&priv->rxlock); spin_lock_init(&priv->bflock); INIT_WORK(&priv->reset_task, gfar_reset_task); dev_set_drvdata(&ofdev->dev, priv); /* Stop the DMA engine now, in case it was running before */ /* (The firmware could have used it, and left it running). */ gfar_halt(dev); /* Reset MAC layer */ gfar_write(&priv->regs->maccfg1, MACCFG1_SOFT_RESET); tempval = (MACCFG1_TX_FLOW | MACCFG1_RX_FLOW); gfar_write(&priv->regs->maccfg1, tempval); /* Initialize MACCFG2. */ gfar_write(&priv->regs->maccfg2, MACCFG2_INIT_SETTINGS); /* Initialize ECNTRL */ gfar_write(&priv->regs->ecntrl, ECNTRL_INIT_SETTINGS); /* Set the dev->base_addr to the gfar reg region */ dev->base_addr = (unsigned long) (priv->regs); SET_NETDEV_DEV(dev, &ofdev->dev); /* Fill in the dev structure */ dev->open = gfar_enet_open; dev->hard_start_xmit = gfar_start_xmit; dev->tx_timeout = gfar_timeout; dev->watchdog_timeo = TX_TIMEOUT; netif_napi_add(dev, &priv->napi, gfar_poll, GFAR_DEV_WEIGHT); #ifdef CONFIG_NET_POLL_CONTROLLER dev->poll_controller = gfar_netpoll; #endif dev->stop = gfar_close; dev->change_mtu = gfar_change_mtu; dev->mtu = 1500; dev->set_multicast_list = gfar_set_multi; dev->ethtool_ops = &gfar_ethtool_ops; dev->do_ioctl = gfar_ioctl; if (priv->device_flags & FSL_GIANFAR_DEV_HAS_CSUM) { priv->rx_csum_enable = 1; dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_HIGHDMA; } else priv->rx_csum_enable = 0; priv->vlgrp = NULL; if (priv->device_flags & FSL_GIANFAR_DEV_HAS_VLAN) { dev->vlan_rx_register = gfar_vlan_rx_register; dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; } if (priv->device_flags & FSL_GIANFAR_DEV_HAS_EXTENDED_HASH) { priv->extended_hash = 1; priv->hash_width = 9; priv->hash_regs[0] = &priv->regs->igaddr0; priv->hash_regs[1] = &priv->regs->igaddr1; priv->hash_regs[2] = &priv->regs->igaddr2; priv->hash_regs[3] = &priv->regs->igaddr3; priv->hash_regs[4] = &priv->regs->igaddr4; priv->hash_regs[5] = &priv->regs->igaddr5; priv->hash_regs[6] = &priv->regs->igaddr6; priv->hash_regs[7] = &priv->regs->igaddr7; priv->hash_regs[8] = &priv->regs->gaddr0; priv->hash_regs[9] = &priv->regs->gaddr1; priv->hash_regs[10] = &priv->regs->gaddr2; priv->hash_regs[11] = &priv->regs->gaddr3; priv->hash_regs[12] = &priv->regs->gaddr4; priv->hash_regs[13] = &priv->regs->gaddr5; priv->hash_regs[14] = &priv->regs->gaddr6; priv->hash_regs[15] = &priv->regs->gaddr7; } else { priv->extended_hash = 0; priv->hash_width = 8; priv->hash_regs[0] = &priv->regs->gaddr0; priv->hash_regs[1] = &priv->regs->gaddr1; priv->hash_regs[2] = &priv->regs->gaddr2; priv->hash_regs[3] = &priv->regs->gaddr3; priv->hash_regs[4] = &priv->regs->gaddr4; priv->hash_regs[5] = &priv->regs->gaddr5; priv->hash_regs[6] = &priv->regs->gaddr6; priv->hash_regs[7] = &priv->regs->gaddr7; } if (priv->device_flags & FSL_GIANFAR_DEV_HAS_PADDING) priv->padding = DEFAULT_PADDING; else priv->padding = 0; if (dev->features & NETIF_F_IP_CSUM) dev->hard_header_len += GMAC_FCB_LEN; priv->rx_buffer_size = DEFAULT_RX_BUFFER_SIZE; priv->tx_ring_size = DEFAULT_TX_RING_SIZE; priv->rx_ring_size = DEFAULT_RX_RING_SIZE; priv->num_txbdfree = DEFAULT_TX_RING_SIZE; priv->txcoalescing = DEFAULT_TX_COALESCE; priv->txic = DEFAULT_TXIC; priv->rxcoalescing = DEFAULT_RX_COALESCE; priv->rxic = DEFAULT_RXIC; /* Enable most messages by default */ priv->msg_enable = (NETIF_MSG_IFUP << 1 ) - 1; /* Carrier starts down, phylib will bring it up */ netif_carrier_off(dev); err = register_netdev(dev); if (err) { printk(KERN_ERR "%s: Cannot register net device, aborting.\n", dev->name); goto register_fail; } device_init_wakeup(&dev->dev, priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET); /* fill out IRQ number and name fields */ len_devname = strlen(dev->name); strncpy(&priv->int_name_tx[0], dev->name, len_devname); if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { strncpy(&priv->int_name_tx[len_devname], "_tx", sizeof("_tx") + 1); strncpy(&priv->int_name_rx[0], dev->name, len_devname); strncpy(&priv->int_name_rx[len_devname], "_rx", sizeof("_rx") + 1); strncpy(&priv->int_name_er[0], dev->name, len_devname); strncpy(&priv->int_name_er[len_devname], "_er", sizeof("_er") + 1); } else priv->int_name_tx[len_devname] = '\0'; /* Create all the sysfs files */ gfar_init_sysfs(dev); /* Print out the device info */ printk(KERN_INFO DEVICE_NAME "%pM\n", dev->name, dev->dev_addr); /* Even more device info helps when determining which kernel */ /* provided which set of benchmarks. */ printk(KERN_INFO "%s: Running with NAPI enabled\n", dev->name); printk(KERN_INFO "%s: %d/%d RX/TX BD ring size\n", dev->name, priv->rx_ring_size, priv->tx_ring_size); return 0; register_fail: iounmap(priv->regs); regs_fail: free_netdev(dev); return err; } static int gfar_remove(struct of_device *ofdev) { struct gfar_private *priv = dev_get_drvdata(&ofdev->dev); dev_set_drvdata(&ofdev->dev, NULL); iounmap(priv->regs); free_netdev(priv->dev); return 0; } #ifdef CONFIG_PM static int gfar_suspend(struct of_device *ofdev, pm_message_t state) { struct gfar_private *priv = dev_get_drvdata(&ofdev->dev); struct net_device *dev = priv->dev; unsigned long flags; u32 tempval; int magic_packet = priv->wol_en && (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET); netif_device_detach(dev); if (netif_running(dev)) { spin_lock_irqsave(&priv->txlock, flags); spin_lock(&priv->rxlock); gfar_halt_nodisable(dev); /* Disable Tx, and Rx if wake-on-LAN is disabled. */ tempval = gfar_read(&priv->regs->maccfg1); tempval &= ~MACCFG1_TX_EN; if (!magic_packet) tempval &= ~MACCFG1_RX_EN; gfar_write(&priv->regs->maccfg1, tempval); spin_unlock(&priv->rxlock); spin_unlock_irqrestore(&priv->txlock, flags); napi_disable(&priv->napi); if (magic_packet) { /* Enable interrupt on Magic Packet */ gfar_write(&priv->regs->imask, IMASK_MAG); /* Enable Magic Packet mode */ tempval = gfar_read(&priv->regs->maccfg2); tempval |= MACCFG2_MPEN; gfar_write(&priv->regs->maccfg2, tempval); } else { phy_stop(priv->phydev); } } return 0; } static int gfar_resume(struct of_device *ofdev) { struct gfar_private *priv = dev_get_drvdata(&ofdev->dev); struct net_device *dev = priv->dev; unsigned long flags; u32 tempval; int magic_packet = priv->wol_en && (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET); if (!netif_running(dev)) { netif_device_attach(dev); return 0; } if (!magic_packet && priv->phydev) phy_start(priv->phydev); /* Disable Magic Packet mode, in case something * else woke us up. */ spin_lock_irqsave(&priv->txlock, flags); spin_lock(&priv->rxlock); tempval = gfar_read(&priv->regs->maccfg2); tempval &= ~MACCFG2_MPEN; gfar_write(&priv->regs->maccfg2, tempval); gfar_start(dev); spin_unlock(&priv->rxlock); spin_unlock_irqrestore(&priv->txlock, flags); netif_device_attach(dev); napi_enable(&priv->napi); return 0; } #else #define gfar_suspend NULL #define gfar_resume NULL #endif /* Reads the controller's registers to determine what interface * connects it to the PHY. */ static phy_interface_t gfar_get_interface(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); u32 ecntrl = gfar_read(&priv->regs->ecntrl); if (ecntrl & ECNTRL_SGMII_MODE) return PHY_INTERFACE_MODE_SGMII; if (ecntrl & ECNTRL_TBI_MODE) { if (ecntrl & ECNTRL_REDUCED_MODE) return PHY_INTERFACE_MODE_RTBI; else return PHY_INTERFACE_MODE_TBI; } if (ecntrl & ECNTRL_REDUCED_MODE) { if (ecntrl & ECNTRL_REDUCED_MII_MODE) return PHY_INTERFACE_MODE_RMII; else { phy_interface_t interface = priv->interface; /* * This isn't autodetected right now, so it must * be set by the device tree or platform code. */ if (interface == PHY_INTERFACE_MODE_RGMII_ID) return PHY_INTERFACE_MODE_RGMII_ID; return PHY_INTERFACE_MODE_RGMII; } } if (priv->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT) return PHY_INTERFACE_MODE_GMII; return PHY_INTERFACE_MODE_MII; } /* Initializes driver's PHY state, and attaches to the PHY. * Returns 0 on success. */ static int init_phy(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); uint gigabit_support = priv->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ? SUPPORTED_1000baseT_Full : 0; struct phy_device *phydev; phy_interface_t interface; priv->oldlink = 0; priv->oldspeed = 0; priv->oldduplex = -1; interface = gfar_get_interface(dev); phydev = phy_connect(dev, priv->phy_bus_id, &adjust_link, 0, interface); if (interface == PHY_INTERFACE_MODE_SGMII) gfar_configure_serdes(dev); if (IS_ERR(phydev)) { printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); return PTR_ERR(phydev); } /* Remove any features not supported by the controller */ phydev->supported &= (GFAR_SUPPORTED | gigabit_support); phydev->advertising = phydev->supported; priv->phydev = phydev; return 0; } /* * Initialize TBI PHY interface for communicating with the * SERDES lynx PHY on the chip. We communicate with this PHY * through the MDIO bus on each controller, treating it as a * "normal" PHY at the address found in the TBIPA register. We assume * that the TBIPA register is valid. Either the MDIO bus code will set * it to a value that doesn't conflict with other PHYs on the bus, or the * value doesn't matter, as there are no other PHYs on the bus. */ static void gfar_configure_serdes(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); if (!priv->tbiphy) { printk(KERN_WARNING "SGMII mode requires that the device " "tree specify a tbi-handle\n"); return; } /* * If the link is already up, we must already be ok, and don't need to * configure and reset the TBI<->SerDes link. Maybe U-Boot configured * everything for us? Resetting it takes the link down and requires * several seconds for it to come back. */ if (phy_read(priv->tbiphy, MII_BMSR) & BMSR_LSTATUS) return; /* Single clk mode, mii mode off(for serdes communication) */ phy_write(priv->tbiphy, MII_TBICON, TBICON_CLK_SELECT); phy_write(priv->tbiphy, MII_ADVERTISE, ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE | ADVERTISE_1000XPSE_ASYM); phy_write(priv->tbiphy, MII_BMCR, BMCR_ANENABLE | BMCR_ANRESTART | BMCR_FULLDPLX | BMCR_SPEED1000); } static void init_registers(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); /* Clear IEVENT */ gfar_write(&priv->regs->ievent, IEVENT_INIT_CLEAR); /* Initialize IMASK */ gfar_write(&priv->regs->imask, IMASK_INIT_CLEAR); /* Init hash registers to zero */ gfar_write(&priv->regs->igaddr0, 0); gfar_write(&priv->regs->igaddr1, 0); gfar_write(&priv->regs->igaddr2, 0); gfar_write(&priv->regs->igaddr3, 0); gfar_write(&priv->regs->igaddr4, 0); gfar_write(&priv->regs->igaddr5, 0); gfar_write(&priv->regs->igaddr6, 0); gfar_write(&priv->regs->igaddr7, 0); gfar_write(&priv->regs->gaddr0, 0); gfar_write(&priv->regs->gaddr1, 0); gfar_write(&priv->regs->gaddr2, 0); gfar_write(&priv->regs->gaddr3, 0); gfar_write(&priv->regs->gaddr4, 0); gfar_write(&priv->regs->gaddr5, 0); gfar_write(&priv->regs->gaddr6, 0); gfar_write(&priv->regs->gaddr7, 0); /* Zero out the rmon mib registers if it has them */ if (priv->device_flags & FSL_GIANFAR_DEV_HAS_RMON) { memset_io(&(priv->regs->rmon), 0, sizeof (struct rmon_mib)); /* Mask off the CAM interrupts */ gfar_write(&priv->regs->rmon.cam1, 0xffffffff); gfar_write(&priv->regs->rmon.cam2, 0xffffffff); } /* Initialize the max receive buffer length */ gfar_write(&priv->regs->mrblr, priv->rx_buffer_size); /* Initialize the Minimum Frame Length Register */ gfar_write(&priv->regs->minflr, MINFLR_INIT_SETTINGS); } /* Halt the receive and transmit queues */ static void gfar_halt_nodisable(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; u32 tempval; /* Mask all interrupts */ gfar_write(®s->imask, IMASK_INIT_CLEAR); /* Clear all interrupts */ gfar_write(®s->ievent, IEVENT_INIT_CLEAR); /* Stop the DMA, and wait for it to stop */ tempval = gfar_read(&priv->regs->dmactrl); if ((tempval & (DMACTRL_GRS | DMACTRL_GTS)) != (DMACTRL_GRS | DMACTRL_GTS)) { tempval |= (DMACTRL_GRS | DMACTRL_GTS); gfar_write(&priv->regs->dmactrl, tempval); while (!(gfar_read(&priv->regs->ievent) & (IEVENT_GRSC | IEVENT_GTSC))) cpu_relax(); } } /* Halt the receive and transmit queues */ void gfar_halt(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; u32 tempval; gfar_halt_nodisable(dev); /* Disable Rx and Tx */ tempval = gfar_read(®s->maccfg1); tempval &= ~(MACCFG1_RX_EN | MACCFG1_TX_EN); gfar_write(®s->maccfg1, tempval); } void stop_gfar(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; unsigned long flags; phy_stop(priv->phydev); /* Lock it down */ spin_lock_irqsave(&priv->txlock, flags); spin_lock(&priv->rxlock); gfar_halt(dev); spin_unlock(&priv->rxlock); spin_unlock_irqrestore(&priv->txlock, flags); /* Free the IRQs */ if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { free_irq(priv->interruptError, dev); free_irq(priv->interruptTransmit, dev); free_irq(priv->interruptReceive, dev); } else { free_irq(priv->interruptTransmit, dev); } free_skb_resources(priv); dma_free_coherent(&dev->dev, sizeof(struct txbd8)*priv->tx_ring_size + sizeof(struct rxbd8)*priv->rx_ring_size, priv->tx_bd_base, gfar_read(®s->tbase0)); } /* If there are any tx skbs or rx skbs still around, free them. * Then free tx_skbuff and rx_skbuff */ static void free_skb_resources(struct gfar_private *priv) { struct rxbd8 *rxbdp; struct txbd8 *txbdp; int i, j; /* Go through all the buffer descriptors and free their data buffers */ txbdp = priv->tx_bd_base; for (i = 0; i < priv->tx_ring_size; i++) { if (!priv->tx_skbuff[i]) continue; dma_unmap_single(&priv->dev->dev, txbdp->bufPtr, txbdp->length, DMA_TO_DEVICE); txbdp->lstatus = 0; for (j = 0; j < skb_shinfo(priv->tx_skbuff[i])->nr_frags; j++) { txbdp++; dma_unmap_page(&priv->dev->dev, txbdp->bufPtr, txbdp->length, DMA_TO_DEVICE); } txbdp++; dev_kfree_skb_any(priv->tx_skbuff[i]); priv->tx_skbuff[i] = NULL; } kfree(priv->tx_skbuff); rxbdp = priv->rx_bd_base; /* rx_skbuff is not guaranteed to be allocated, so only * free it and its contents if it is allocated */ if(priv->rx_skbuff != NULL) { for (i = 0; i < priv->rx_ring_size; i++) { if (priv->rx_skbuff[i]) { dma_unmap_single(&priv->dev->dev, rxbdp->bufPtr, priv->rx_buffer_size, DMA_FROM_DEVICE); dev_kfree_skb_any(priv->rx_skbuff[i]); priv->rx_skbuff[i] = NULL; } rxbdp->lstatus = 0; rxbdp->bufPtr = 0; rxbdp++; } kfree(priv->rx_skbuff); } } void gfar_start(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; u32 tempval; /* Enable Rx and Tx in MACCFG1 */ tempval = gfar_read(®s->maccfg1); tempval |= (MACCFG1_RX_EN | MACCFG1_TX_EN); gfar_write(®s->maccfg1, tempval); /* Initialize DMACTRL to have WWR and WOP */ tempval = gfar_read(&priv->regs->dmactrl); tempval |= DMACTRL_INIT_SETTINGS; gfar_write(&priv->regs->dmactrl, tempval); /* Make sure we aren't stopped */ tempval = gfar_read(&priv->regs->dmactrl); tempval &= ~(DMACTRL_GRS | DMACTRL_GTS); gfar_write(&priv->regs->dmactrl, tempval); /* Clear THLT/RHLT, so that the DMA starts polling now */ gfar_write(®s->tstat, TSTAT_CLEAR_THALT); gfar_write(®s->rstat, RSTAT_CLEAR_RHALT); /* Unmask the interrupts we look for */ gfar_write(®s->imask, IMASK_DEFAULT); dev->trans_start = jiffies; } /* Bring the controller up and running */ int startup_gfar(struct net_device *dev) { struct txbd8 *txbdp; struct rxbd8 *rxbdp; dma_addr_t addr = 0; unsigned long vaddr; int i; struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; int err = 0; u32 rctrl = 0; u32 attrs = 0; gfar_write(®s->imask, IMASK_INIT_CLEAR); /* Allocate memory for the buffer descriptors */ vaddr = (unsigned long) dma_alloc_coherent(&dev->dev, sizeof (struct txbd8) * priv->tx_ring_size + sizeof (struct rxbd8) * priv->rx_ring_size, &addr, GFP_KERNEL); if (vaddr == 0) { if (netif_msg_ifup(priv)) printk(KERN_ERR "%s: Could not allocate buffer descriptors!\n", dev->name); return -ENOMEM; } priv->tx_bd_base = (struct txbd8 *) vaddr; /* enet DMA only understands physical addresses */ gfar_write(®s->tbase0, addr); /* Start the rx descriptor ring where the tx ring leaves off */ addr = addr + sizeof (struct txbd8) * priv->tx_ring_size; vaddr = vaddr + sizeof (struct txbd8) * priv->tx_ring_size; priv->rx_bd_base = (struct rxbd8 *) vaddr; gfar_write(®s->rbase0, addr); /* Setup the skbuff rings */ priv->tx_skbuff = (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) * priv->tx_ring_size, GFP_KERNEL); if (NULL == priv->tx_skbuff) { if (netif_msg_ifup(priv)) printk(KERN_ERR "%s: Could not allocate tx_skbuff\n", dev->name); err = -ENOMEM; goto tx_skb_fail; } for (i = 0; i < priv->tx_ring_size; i++) priv->tx_skbuff[i] = NULL; priv->rx_skbuff = (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) * priv->rx_ring_size, GFP_KERNEL); if (NULL == priv->rx_skbuff) { if (netif_msg_ifup(priv)) printk(KERN_ERR "%s: Could not allocate rx_skbuff\n", dev->name); err = -ENOMEM; goto rx_skb_fail; } for (i = 0; i < priv->rx_ring_size; i++) priv->rx_skbuff[i] = NULL; /* Initialize some variables in our dev structure */ priv->num_txbdfree = priv->tx_ring_size; priv->dirty_tx = priv->cur_tx = priv->tx_bd_base; priv->cur_rx = priv->rx_bd_base; priv->skb_curtx = priv->skb_dirtytx = 0; priv->skb_currx = 0; /* Initialize Transmit Descriptor Ring */ txbdp = priv->tx_bd_base; for (i = 0; i < priv->tx_ring_size; i++) { txbdp->lstatus = 0; txbdp->bufPtr = 0; txbdp++; } /* Set the last descriptor in the ring to indicate wrap */ txbdp--; txbdp->status |= TXBD_WRAP; rxbdp = priv->rx_bd_base; for (i = 0; i < priv->rx_ring_size; i++) { struct sk_buff *skb; skb = gfar_new_skb(dev); if (!skb) { printk(KERN_ERR "%s: Can't allocate RX buffers\n", dev->name); goto err_rxalloc_fail; } priv->rx_skbuff[i] = skb; gfar_new_rxbdp(dev, rxbdp, skb); rxbdp++; } /* Set the last descriptor in the ring to wrap */ rxbdp--; rxbdp->status |= RXBD_WRAP; /* If the device has multiple interrupts, register for * them. Otherwise, only register for the one */ if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { /* Install our interrupt handlers for Error, * Transmit, and Receive */ if (request_irq(priv->interruptError, gfar_error, 0, priv->int_name_er, dev) < 0) { if (netif_msg_intr(priv)) printk(KERN_ERR "%s: Can't get IRQ %d\n", dev->name, priv->interruptError); err = -1; goto err_irq_fail; } if (request_irq(priv->interruptTransmit, gfar_transmit, 0, priv->int_name_tx, dev) < 0) { if (netif_msg_intr(priv)) printk(KERN_ERR "%s: Can't get IRQ %d\n", dev->name, priv->interruptTransmit); err = -1; goto tx_irq_fail; } if (request_irq(priv->interruptReceive, gfar_receive, 0, priv->int_name_rx, dev) < 0) { if (netif_msg_intr(priv)) printk(KERN_ERR "%s: Can't get IRQ %d (receive0)\n", dev->name, priv->interruptReceive); err = -1; goto rx_irq_fail; } } else { if (request_irq(priv->interruptTransmit, gfar_interrupt, 0, priv->int_name_tx, dev) < 0) { if (netif_msg_intr(priv)) printk(KERN_ERR "%s: Can't get IRQ %d\n", dev->name, priv->interruptTransmit); err = -1; goto err_irq_fail; } } phy_start(priv->phydev); /* Configure the coalescing support */ gfar_write(®s->txic, 0); if (priv->txcoalescing) gfar_write(®s->txic, priv->txic); gfar_write(®s->rxic, 0); if (priv->rxcoalescing) gfar_write(®s->rxic, priv->rxic); if (priv->rx_csum_enable) rctrl |= RCTRL_CHECKSUMMING; if (priv->extended_hash) { rctrl |= RCTRL_EXTHASH; gfar_clear_exact_match(dev); rctrl |= RCTRL_EMEN; } if (priv->padding) { rctrl &= ~RCTRL_PAL_MASK; rctrl |= RCTRL_PADDING(priv->padding); } /* Init rctrl based on our settings */ gfar_write(&priv->regs->rctrl, rctrl); if (dev->features & NETIF_F_IP_CSUM) gfar_write(&priv->regs->tctrl, TCTRL_INIT_CSUM); /* Set the extraction length and index */ attrs = ATTRELI_EL(priv->rx_stash_size) | ATTRELI_EI(priv->rx_stash_index); gfar_write(&priv->regs->attreli, attrs); /* Start with defaults, and add stashing or locking * depending on the approprate variables */ attrs = ATTR_INIT_SETTINGS; if (priv->bd_stash_en) attrs |= ATTR_BDSTASH; if (priv->rx_stash_size != 0) attrs |= ATTR_BUFSTASH; gfar_write(&priv->regs->attr, attrs); gfar_write(&priv->regs->fifo_tx_thr, priv->fifo_threshold); gfar_write(&priv->regs->fifo_tx_starve, priv->fifo_starve); gfar_write(&priv->regs->fifo_tx_starve_shutoff, priv->fifo_starve_off); /* Start the controller */ gfar_start(dev); return 0; rx_irq_fail: free_irq(priv->interruptTransmit, dev); tx_irq_fail: free_irq(priv->interruptError, dev); err_irq_fail: err_rxalloc_fail: rx_skb_fail: free_skb_resources(priv); tx_skb_fail: dma_free_coherent(&dev->dev, sizeof(struct txbd8)*priv->tx_ring_size + sizeof(struct rxbd8)*priv->rx_ring_size, priv->tx_bd_base, gfar_read(®s->tbase0)); return err; } /* Called when something needs to use the ethernet device */ /* Returns 0 for success. */ static int gfar_enet_open(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); int err; napi_enable(&priv->napi); /* Initialize a bunch of registers */ init_registers(dev); gfar_set_mac_address(dev); err = init_phy(dev); if(err) { napi_disable(&priv->napi); return err; } err = startup_gfar(dev); if (err) { napi_disable(&priv->napi); return err; } netif_start_queue(dev); device_set_wakeup_enable(&dev->dev, priv->wol_en); return err; } static inline struct txfcb *gfar_add_fcb(struct sk_buff *skb) { struct txfcb *fcb = (struct txfcb *)skb_push (skb, GMAC_FCB_LEN); cacheable_memzero(fcb, GMAC_FCB_LEN); return fcb; } static inline void gfar_tx_checksum(struct sk_buff *skb, struct txfcb *fcb) { u8 flags = 0; /* If we're here, it's a IP packet with a TCP or UDP * payload. We set it to checksum, using a pseudo-header * we provide */ flags = TXFCB_DEFAULT; /* Tell the controller what the protocol is */ /* And provide the already calculated phcs */ if (ip_hdr(skb)->protocol == IPPROTO_UDP) { flags |= TXFCB_UDP; fcb->phcs = udp_hdr(skb)->check; } else fcb->phcs = tcp_hdr(skb)->check; /* l3os is the distance between the start of the * frame (skb->data) and the start of the IP hdr. * l4os is the distance between the start of the * l3 hdr and the l4 hdr */ fcb->l3os = (u16)(skb_network_offset(skb) - GMAC_FCB_LEN); fcb->l4os = skb_network_header_len(skb); fcb->flags = flags; } void inline gfar_tx_vlan(struct sk_buff *skb, struct txfcb *fcb) { fcb->flags |= TXFCB_VLN; fcb->vlctl = vlan_tx_tag_get(skb); } static inline struct txbd8 *skip_txbd(struct txbd8 *bdp, int stride, struct txbd8 *base, int ring_size) { struct txbd8 *new_bd = bdp + stride; return (new_bd >= (base + ring_size)) ? (new_bd - ring_size) : new_bd; } static inline struct txbd8 *next_txbd(struct txbd8 *bdp, struct txbd8 *base, int ring_size) { return skip_txbd(bdp, 1, base, ring_size); } /* This is called by the kernel when a frame is ready for transmission. */ /* It is pointed to by the dev->hard_start_xmit function pointer */ static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct txfcb *fcb = NULL; struct txbd8 *txbdp, *txbdp_start, *base; u32 lstatus; int i; u32 bufaddr; unsigned long flags; unsigned int nr_frags, length; base = priv->tx_bd_base; /* total number of fragments in the SKB */ nr_frags = skb_shinfo(skb)->nr_frags; spin_lock_irqsave(&priv->txlock, flags); /* check if there is space to queue this packet */ if (nr_frags > priv->num_txbdfree) { /* no space, stop the queue */ netif_stop_queue(dev); dev->stats.tx_fifo_errors++; spin_unlock_irqrestore(&priv->txlock, flags); return NETDEV_TX_BUSY; } /* Update transmit stats */ dev->stats.tx_bytes += skb->len; txbdp = txbdp_start = priv->cur_tx; if (nr_frags == 0) { lstatus = txbdp->lstatus | BD_LFLAG(TXBD_LAST | TXBD_INTERRUPT); } else { /* Place the fragment addresses and lengths into the TxBDs */ for (i = 0; i < nr_frags; i++) { /* Point at the next BD, wrapping as needed */ txbdp = next_txbd(txbdp, base, priv->tx_ring_size); length = skb_shinfo(skb)->frags[i].size; lstatus = txbdp->lstatus | length | BD_LFLAG(TXBD_READY); /* Handle the last BD specially */ if (i == nr_frags - 1) lstatus |= BD_LFLAG(TXBD_LAST | TXBD_INTERRUPT); bufaddr = dma_map_page(&dev->dev, skb_shinfo(skb)->frags[i].page, skb_shinfo(skb)->frags[i].page_offset, length, DMA_TO_DEVICE); /* set the TxBD length and buffer pointer */ txbdp->bufPtr = bufaddr; txbdp->lstatus = lstatus; } lstatus = txbdp_start->lstatus; } /* Set up checksumming */ if (CHECKSUM_PARTIAL == skb->ip_summed) { fcb = gfar_add_fcb(skb); lstatus |= BD_LFLAG(TXBD_TOE); gfar_tx_checksum(skb, fcb); } if (priv->vlgrp && vlan_tx_tag_present(skb)) { if (unlikely(NULL == fcb)) { fcb = gfar_add_fcb(skb); lstatus |= BD_LFLAG(TXBD_TOE); } gfar_tx_vlan(skb, fcb); } /* setup the TxBD length and buffer pointer for the first BD */ priv->tx_skbuff[priv->skb_curtx] = skb; txbdp_start->bufPtr = dma_map_single(&dev->dev, skb->data, skb_headlen(skb), DMA_TO_DEVICE); lstatus |= BD_LFLAG(TXBD_CRC | TXBD_READY) | skb_headlen(skb); /* * The powerpc-specific eieio() is used, as wmb() has too strong * semantics (it requires synchronization between cacheable and * uncacheable mappings, which eieio doesn't provide and which we * don't need), thus requiring a more expensive sync instruction. At * some point, the set of architecture-independent barrier functions * should be expanded to include weaker barriers. */ eieio(); txbdp_start->lstatus = lstatus; /* Update the current skb pointer to the next entry we will use * (wrapping if necessary) */ priv->skb_curtx = (priv->skb_curtx + 1) & TX_RING_MOD_MASK(priv->tx_ring_size); priv->cur_tx = next_txbd(txbdp, base, priv->tx_ring_size); /* reduce TxBD free count */ priv->num_txbdfree -= (nr_frags + 1); dev->trans_start = jiffies; /* If the next BD still needs to be cleaned up, then the bds are full. We need to tell the kernel to stop sending us stuff. */ if (!priv->num_txbdfree) { netif_stop_queue(dev); dev->stats.tx_fifo_errors++; } /* Tell the DMA to go go go */ gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT); /* Unlock priv */ spin_unlock_irqrestore(&priv->txlock, flags); return 0; } /* Stops the kernel queue, and halts the controller */ static int gfar_close(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); napi_disable(&priv->napi); cancel_work_sync(&priv->reset_task); stop_gfar(dev); /* Disconnect from the PHY */ phy_disconnect(priv->phydev); priv->phydev = NULL; netif_stop_queue(dev); return 0; } /* Changes the mac address if the controller is not running. */ static int gfar_set_mac_address(struct net_device *dev) { gfar_set_mac_for_addr(dev, 0, dev->dev_addr); return 0; } /* Enables and disables VLAN insertion/extraction */ static void gfar_vlan_rx_register(struct net_device *dev, struct vlan_group *grp) { struct gfar_private *priv = netdev_priv(dev); unsigned long flags; u32 tempval; spin_lock_irqsave(&priv->rxlock, flags); priv->vlgrp = grp; if (grp) { /* Enable VLAN tag insertion */ tempval = gfar_read(&priv->regs->tctrl); tempval |= TCTRL_VLINS; gfar_write(&priv->regs->tctrl, tempval); /* Enable VLAN tag extraction */ tempval = gfar_read(&priv->regs->rctrl); tempval |= RCTRL_VLEX; tempval |= (RCTRL_VLEX | RCTRL_PRSDEP_INIT); gfar_write(&priv->regs->rctrl, tempval); } else { /* Disable VLAN tag insertion */ tempval = gfar_read(&priv->regs->tctrl); tempval &= ~TCTRL_VLINS; gfar_write(&priv->regs->tctrl, tempval); /* Disable VLAN tag extraction */ tempval = gfar_read(&priv->regs->rctrl); tempval &= ~RCTRL_VLEX; /* If parse is no longer required, then disable parser */ if (tempval & RCTRL_REQ_PARSER) tempval |= RCTRL_PRSDEP_INIT; else tempval &= ~RCTRL_PRSDEP_INIT; gfar_write(&priv->regs->rctrl, tempval); } gfar_change_mtu(dev, dev->mtu); spin_unlock_irqrestore(&priv->rxlock, flags); } static int gfar_change_mtu(struct net_device *dev, int new_mtu) { int tempsize, tempval; struct gfar_private *priv = netdev_priv(dev); int oldsize = priv->rx_buffer_size; int frame_size = new_mtu + ETH_HLEN; if (priv->vlgrp) frame_size += VLAN_HLEN; if ((frame_size < 64) || (frame_size > JUMBO_FRAME_SIZE)) { if (netif_msg_drv(priv)) printk(KERN_ERR "%s: Invalid MTU setting\n", dev->name); return -EINVAL; } if (gfar_uses_fcb(priv)) frame_size += GMAC_FCB_LEN; frame_size += priv->padding; tempsize = (frame_size & ~(INCREMENTAL_BUFFER_SIZE - 1)) + INCREMENTAL_BUFFER_SIZE; /* Only stop and start the controller if it isn't already * stopped, and we changed something */ if ((oldsize != tempsize) && (dev->flags & IFF_UP)) stop_gfar(dev); priv->rx_buffer_size = tempsize; dev->mtu = new_mtu; gfar_write(&priv->regs->mrblr, priv->rx_buffer_size); gfar_write(&priv->regs->maxfrm, priv->rx_buffer_size); /* If the mtu is larger than the max size for standard * ethernet frames (ie, a jumbo frame), then set maccfg2 * to allow huge frames, and to check the length */ tempval = gfar_read(&priv->regs->maccfg2); if (priv->rx_buffer_size > DEFAULT_RX_BUFFER_SIZE) tempval |= (MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK); else tempval &= ~(MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK); gfar_write(&priv->regs->maccfg2, tempval); if ((oldsize != tempsize) && (dev->flags & IFF_UP)) startup_gfar(dev); return 0; } /* gfar_reset_task gets scheduled when a packet has not been * transmitted after a set amount of time. * For now, assume that clearing out all the structures, and * starting over will fix the problem. */ static void gfar_reset_task(struct work_struct *work) { struct gfar_private *priv = container_of(work, struct gfar_private, reset_task); struct net_device *dev = priv->dev; if (dev->flags & IFF_UP) { stop_gfar(dev); startup_gfar(dev); } netif_tx_schedule_all(dev); } static void gfar_timeout(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); dev->stats.tx_errors++; schedule_work(&priv->reset_task); } /* Interrupt Handler for Transmit complete */ static int gfar_clean_tx_ring(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct txbd8 *bdp; struct txbd8 *lbdp = NULL; struct txbd8 *base = priv->tx_bd_base; struct sk_buff *skb; int skb_dirtytx; int tx_ring_size = priv->tx_ring_size; int frags = 0; int i; int howmany = 0; u32 lstatus; bdp = priv->dirty_tx; skb_dirtytx = priv->skb_dirtytx; while ((skb = priv->tx_skbuff[skb_dirtytx])) { frags = skb_shinfo(skb)->nr_frags; lbdp = skip_txbd(bdp, frags, base, tx_ring_size); lstatus = lbdp->lstatus; /* Only clean completed frames */ if ((lstatus & BD_LFLAG(TXBD_READY)) && (lstatus & BD_LENGTH_MASK)) break; dma_unmap_single(&dev->dev, bdp->bufPtr, bdp->length, DMA_TO_DEVICE); bdp->lstatus &= BD_LFLAG(TXBD_WRAP); bdp = next_txbd(bdp, base, tx_ring_size); for (i = 0; i < frags; i++) { dma_unmap_page(&dev->dev, bdp->bufPtr, bdp->length, DMA_TO_DEVICE); bdp->lstatus &= BD_LFLAG(TXBD_WRAP); bdp = next_txbd(bdp, base, tx_ring_size); } dev_kfree_skb_any(skb); priv->tx_skbuff[skb_dirtytx] = NULL; skb_dirtytx = (skb_dirtytx + 1) & TX_RING_MOD_MASK(tx_ring_size); howmany++; priv->num_txbdfree += frags + 1; } /* If we freed a buffer, we can restart transmission, if necessary */ if (netif_queue_stopped(dev) && priv->num_txbdfree) netif_wake_queue(dev); /* Update dirty indicators */ priv->skb_dirtytx = skb_dirtytx; priv->dirty_tx = bdp; dev->stats.tx_packets += howmany; return howmany; } static void gfar_schedule_cleanup(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); unsigned long flags; spin_lock_irqsave(&priv->txlock, flags); spin_lock(&priv->rxlock); if (napi_schedule_prep(&priv->napi)) { gfar_write(&priv->regs->imask, IMASK_RTX_DISABLED); __napi_schedule(&priv->napi); } spin_unlock(&priv->rxlock); spin_unlock_irqrestore(&priv->txlock, flags); } /* Interrupt Handler for Transmit complete */ static irqreturn_t gfar_transmit(int irq, void *dev_id) { gfar_schedule_cleanup((struct net_device *)dev_id); return IRQ_HANDLED; } static void gfar_new_rxbdp(struct net_device *dev, struct rxbd8 *bdp, struct sk_buff *skb) { struct gfar_private *priv = netdev_priv(dev); u32 lstatus; bdp->bufPtr = dma_map_single(&dev->dev, skb->data, priv->rx_buffer_size, DMA_FROM_DEVICE); lstatus = BD_LFLAG(RXBD_EMPTY | RXBD_INTERRUPT); if (bdp == priv->rx_bd_base + priv->rx_ring_size - 1) lstatus |= BD_LFLAG(RXBD_WRAP); eieio(); bdp->lstatus = lstatus; } struct sk_buff * gfar_new_skb(struct net_device *dev) { unsigned int alignamount; struct gfar_private *priv = netdev_priv(dev); struct sk_buff *skb = NULL; /* We have to allocate the skb, so keep trying till we succeed */ skb = netdev_alloc_skb(dev, priv->rx_buffer_size + RXBUF_ALIGNMENT); if (!skb) return NULL; alignamount = RXBUF_ALIGNMENT - (((unsigned long) skb->data) & (RXBUF_ALIGNMENT - 1)); /* We need the data buffer to be aligned properly. We will reserve * as many bytes as needed to align the data properly */ skb_reserve(skb, alignamount); return skb; } static inline void count_errors(unsigned short status, struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct net_device_stats *stats = &dev->stats; struct gfar_extra_stats *estats = &priv->extra_stats; /* If the packet was truncated, none of the other errors * matter */ if (status & RXBD_TRUNCATED) { stats->rx_length_errors++; estats->rx_trunc++; return; } /* Count the errors, if there were any */ if (status & (RXBD_LARGE | RXBD_SHORT)) { stats->rx_length_errors++; if (status & RXBD_LARGE) estats->rx_large++; else estats->rx_short++; } if (status & RXBD_NONOCTET) { stats->rx_frame_errors++; estats->rx_nonoctet++; } if (status & RXBD_CRCERR) { estats->rx_crcerr++; stats->rx_crc_errors++; } if (status & RXBD_OVERRUN) { estats->rx_overrun++; stats->rx_crc_errors++; } } irqreturn_t gfar_receive(int irq, void *dev_id) { gfar_schedule_cleanup((struct net_device *)dev_id); return IRQ_HANDLED; } static inline void gfar_rx_checksum(struct sk_buff *skb, struct rxfcb *fcb) { /* If valid headers were found, and valid sums * were verified, then we tell the kernel that no * checksumming is necessary. Otherwise, it is */ if ((fcb->flags & RXFCB_CSUM_MASK) == (RXFCB_CIP | RXFCB_CTU)) skb->ip_summed = CHECKSUM_UNNECESSARY; else skb->ip_summed = CHECKSUM_NONE; } /* gfar_process_frame() -- handle one incoming packet if skb * isn't NULL. */ static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int amount_pull) { struct gfar_private *priv = netdev_priv(dev); struct rxfcb *fcb = NULL; int ret; /* fcb is at the beginning if exists */ fcb = (struct rxfcb *)skb->data; /* Remove the FCB from the skb */ /* Remove the padded bytes, if there are any */ if (amount_pull) skb_pull(skb, amount_pull); if (priv->rx_csum_enable) gfar_rx_checksum(skb, fcb); /* Tell the skb what kind of packet this is */ skb->protocol = eth_type_trans(skb, dev); /* Send the packet up the stack */ if (unlikely(priv->vlgrp && (fcb->flags & RXFCB_VLN))) ret = vlan_hwaccel_receive_skb(skb, priv->vlgrp, fcb->vlctl); else ret = netif_receive_skb(skb); if (NET_RX_DROP == ret) priv->extra_stats.kernel_dropped++; return 0; } /* gfar_clean_rx_ring() -- Processes each frame in the rx ring * until the budget/quota has been reached. Returns the number * of frames handled */ int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit) { struct rxbd8 *bdp, *base; struct sk_buff *skb; int pkt_len; int amount_pull; int howmany = 0; struct gfar_private *priv = netdev_priv(dev); /* Get the first full descriptor */ bdp = priv->cur_rx; base = priv->rx_bd_base; amount_pull = (gfar_uses_fcb(priv) ? GMAC_FCB_LEN : 0) + priv->padding; while (!((bdp->status & RXBD_EMPTY) || (--rx_work_limit < 0))) { struct sk_buff *newskb; rmb(); /* Add another skb for the future */ newskb = gfar_new_skb(dev); skb = priv->rx_skbuff[priv->skb_currx]; dma_unmap_single(&priv->dev->dev, bdp->bufPtr, priv->rx_buffer_size, DMA_FROM_DEVICE); /* We drop the frame if we failed to allocate a new buffer */ if (unlikely(!newskb || !(bdp->status & RXBD_LAST) || bdp->status & RXBD_ERR)) { count_errors(bdp->status, dev); if (unlikely(!newskb)) newskb = skb; else if (skb) dev_kfree_skb_any(skb); } else { /* Increment the number of packets */ dev->stats.rx_packets++; howmany++; if (likely(skb)) { pkt_len = bdp->length - ETH_FCS_LEN; /* Remove the FCS from the packet length */ skb_put(skb, pkt_len); dev->stats.rx_bytes += pkt_len; gfar_process_frame(dev, skb, amount_pull); } else { if (netif_msg_rx_err(priv)) printk(KERN_WARNING "%s: Missing skb!\n", dev->name); dev->stats.rx_dropped++; priv->extra_stats.rx_skbmissing++; } } priv->rx_skbuff[priv->skb_currx] = newskb; /* Setup the new bdp */ gfar_new_rxbdp(dev, bdp, newskb); /* Update to the next pointer */ bdp = next_bd(bdp, base, priv->rx_ring_size); /* update to point at the next skb */ priv->skb_currx = (priv->skb_currx + 1) & RX_RING_MOD_MASK(priv->rx_ring_size); } /* Update the current rxbd pointer to be the next one */ priv->cur_rx = bdp; return howmany; } static int gfar_poll(struct napi_struct *napi, int budget) { struct gfar_private *priv = container_of(napi, struct gfar_private, napi); struct net_device *dev = priv->dev; int tx_cleaned = 0; int rx_cleaned = 0; unsigned long flags; /* Clear IEVENT, so interrupts aren't called again * because of the packets that have already arrived */ gfar_write(&priv->regs->ievent, IEVENT_RTX_MASK); /* If we fail to get the lock, don't bother with the TX BDs */ if (spin_trylock_irqsave(&priv->txlock, flags)) { tx_cleaned = gfar_clean_tx_ring(dev); spin_unlock_irqrestore(&priv->txlock, flags); } rx_cleaned = gfar_clean_rx_ring(dev, budget); if (tx_cleaned) return budget; if (rx_cleaned < budget) { napi_complete(napi); /* Clear the halt bit in RSTAT */ gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT); gfar_write(&priv->regs->imask, IMASK_DEFAULT); /* If we are coalescing interrupts, update the timer */ /* Otherwise, clear it */ if (likely(priv->rxcoalescing)) { gfar_write(&priv->regs->rxic, 0); gfar_write(&priv->regs->rxic, priv->rxic); } if (likely(priv->txcoalescing)) { gfar_write(&priv->regs->txic, 0); gfar_write(&priv->regs->txic, priv->txic); } } return rx_cleaned; } #ifdef CONFIG_NET_POLL_CONTROLLER /* * Polling 'interrupt' - used by things like netconsole to send skbs * without having to re-enable interrupts. It's not called while * the interrupt routine is executing. */ static void gfar_netpoll(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); /* If the device has multiple interrupts, run tx/rx */ if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { disable_irq(priv->interruptTransmit); disable_irq(priv->interruptReceive); disable_irq(priv->interruptError); gfar_interrupt(priv->interruptTransmit, dev); enable_irq(priv->interruptError); enable_irq(priv->interruptReceive); enable_irq(priv->interruptTransmit); } else { disable_irq(priv->interruptTransmit); gfar_interrupt(priv->interruptTransmit, dev); enable_irq(priv->interruptTransmit); } } #endif /* The interrupt handler for devices with one interrupt */ static irqreturn_t gfar_interrupt(int irq, void *dev_id) { struct net_device *dev = dev_id; struct gfar_private *priv = netdev_priv(dev); /* Save ievent for future reference */ u32 events = gfar_read(&priv->regs->ievent); /* Check for reception */ if (events & IEVENT_RX_MASK) gfar_receive(irq, dev_id); /* Check for transmit completion */ if (events & IEVENT_TX_MASK) gfar_transmit(irq, dev_id); /* Check for errors */ if (events & IEVENT_ERR_MASK) gfar_error(irq, dev_id); return IRQ_HANDLED; } /* Called every time the controller might need to be made * aware of new link state. The PHY code conveys this * information through variables in the phydev structure, and this * function converts those variables into the appropriate * register values, and can bring down the device if needed. */ static void adjust_link(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; unsigned long flags; struct phy_device *phydev = priv->phydev; int new_state = 0; spin_lock_irqsave(&priv->txlock, flags); if (phydev->link) { u32 tempval = gfar_read(®s->maccfg2); u32 ecntrl = gfar_read(®s->ecntrl); /* Now we make sure that we can be in full duplex mode. * If not, we operate in half-duplex mode. */ if (phydev->duplex != priv->oldduplex) { new_state = 1; if (!(phydev->duplex)) tempval &= ~(MACCFG2_FULL_DUPLEX); else tempval |= MACCFG2_FULL_DUPLEX; priv->oldduplex = phydev->duplex; } if (phydev->speed != priv->oldspeed) { new_state = 1; switch (phydev->speed) { case 1000: tempval = ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII); ecntrl &= ~(ECNTRL_R100); break; case 100: case 10: tempval = ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII); /* Reduced mode distinguishes * between 10 and 100 */ if (phydev->speed == SPEED_100) ecntrl |= ECNTRL_R100; else ecntrl &= ~(ECNTRL_R100); break; default: if (netif_msg_link(priv)) printk(KERN_WARNING "%s: Ack! Speed (%d) is not 10/100/1000!\n", dev->name, phydev->speed); break; } priv->oldspeed = phydev->speed; } gfar_write(®s->maccfg2, tempval); gfar_write(®s->ecntrl, ecntrl); if (!priv->oldlink) { new_state = 1; priv->oldlink = 1; } } else if (priv->oldlink) { new_state = 1; priv->oldlink = 0; priv->oldspeed = 0; priv->oldduplex = -1; } if (new_state && netif_msg_link(priv)) phy_print_status(phydev); spin_unlock_irqrestore(&priv->txlock, flags); } /* Update the hash table based on the current list of multicast * addresses we subscribe to. Also, change the promiscuity of * the device based on the flags (this function is called * whenever dev->flags is changed */ static void gfar_set_multi(struct net_device *dev) { struct dev_mc_list *mc_ptr; struct gfar_private *priv = netdev_priv(dev); struct gfar __iomem *regs = priv->regs; u32 tempval; if(dev->flags & IFF_PROMISC) { /* Set RCTRL to PROM */ tempval = gfar_read(®s->rctrl); tempval |= RCTRL_PROM; gfar_write(®s->rctrl, tempval); } else { /* Set RCTRL to not PROM */ tempval = gfar_read(®s->rctrl); tempval &= ~(RCTRL_PROM); gfar_write(®s->rctrl, tempval); } if(dev->flags & IFF_ALLMULTI) { /* Set the hash to rx all multicast frames */ gfar_write(®s->igaddr0, 0xffffffff); gfar_write(®s->igaddr1, 0xffffffff); gfar_write(®s->igaddr2, 0xffffffff); gfar_write(®s->igaddr3, 0xffffffff); gfar_write(®s->igaddr4, 0xffffffff); gfar_write(®s->igaddr5, 0xffffffff); gfar_write(®s->igaddr6, 0xffffffff); gfar_write(®s->igaddr7, 0xffffffff); gfar_write(®s->gaddr0, 0xffffffff); gfar_write(®s->gaddr1, 0xffffffff); gfar_write(®s->gaddr2, 0xffffffff); gfar_write(®s->gaddr3, 0xffffffff); gfar_write(®s->gaddr4, 0xffffffff); gfar_write(®s->gaddr5, 0xffffffff); gfar_write(®s->gaddr6, 0xffffffff); gfar_write(®s->gaddr7, 0xffffffff); } else { int em_num; int idx; /* zero out the hash */ gfar_write(®s->igaddr0, 0x0); gfar_write(®s->igaddr1, 0x0); gfar_write(®s->igaddr2, 0x0); gfar_write(®s->igaddr3, 0x0); gfar_write(®s->igaddr4, 0x0); gfar_write(®s->igaddr5, 0x0); gfar_write(®s->igaddr6, 0x0); gfar_write(®s->igaddr7, 0x0); gfar_write(®s->gaddr0, 0x0); gfar_write(®s->gaddr1, 0x0); gfar_write(®s->gaddr2, 0x0); gfar_write(®s->gaddr3, 0x0); gfar_write(®s->gaddr4, 0x0); gfar_write(®s->gaddr5, 0x0); gfar_write(®s->gaddr6, 0x0); gfar_write(®s->gaddr7, 0x0); /* If we have extended hash tables, we need to * clear the exact match registers to prepare for * setting them */ if (priv->extended_hash) { em_num = GFAR_EM_NUM + 1; gfar_clear_exact_match(dev); idx = 1; } else { idx = 0; em_num = 0; } if(dev->mc_count == 0) return; /* Parse the list, and set the appropriate bits */ for(mc_ptr = dev->mc_list; mc_ptr; mc_ptr = mc_ptr->next) { if (idx < em_num) { gfar_set_mac_for_addr(dev, idx, mc_ptr->dmi_addr); idx++; } else gfar_set_hash_for_addr(dev, mc_ptr->dmi_addr); } } return; } /* Clears each of the exact match registers to zero, so they * don't interfere with normal reception */ static void gfar_clear_exact_match(struct net_device *dev) { int idx; u8 zero_arr[MAC_ADDR_LEN] = {0,0,0,0,0,0}; for(idx = 1;idx < GFAR_EM_NUM + 1;idx++) gfar_set_mac_for_addr(dev, idx, (u8 *)zero_arr); } /* Set the appropriate hash bit for the given addr */ /* The algorithm works like so: * 1) Take the Destination Address (ie the multicast address), and * do a CRC on it (little endian), and reverse the bits of the * result. * 2) Use the 8 most significant bits as a hash into a 256-entry * table. The table is controlled through 8 32-bit registers: * gaddr0-7. gaddr0's MSB is entry 0, and gaddr7's LSB is * gaddr7. This means that the 3 most significant bits in the * hash index which gaddr register to use, and the 5 other bits * indicate which bit (assuming an IBM numbering scheme, which * for PowerPC (tm) is usually the case) in the register holds * the entry. */ static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr) { u32 tempval; struct gfar_private *priv = netdev_priv(dev); u32 result = ether_crc(MAC_ADDR_LEN, addr); int width = priv->hash_width; u8 whichbit = (result >> (32 - width)) & 0x1f; u8 whichreg = result >> (32 - width + 5); u32 value = (1 << (31-whichbit)); tempval = gfar_read(priv->hash_regs[whichreg]); tempval |= value; gfar_write(priv->hash_regs[whichreg], tempval); return; } /* There are multiple MAC Address register pairs on some controllers * This function sets the numth pair to a given address */ static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr) { struct gfar_private *priv = netdev_priv(dev); int idx; char tmpbuf[MAC_ADDR_LEN]; u32 tempval; u32 __iomem *macptr = &priv->regs->macstnaddr1; macptr += num*2; /* Now copy it into the mac registers backwards, cuz */ /* little endian is silly */ for (idx = 0; idx < MAC_ADDR_LEN; idx++) tmpbuf[MAC_ADDR_LEN - 1 - idx] = addr[idx]; gfar_write(macptr, *((u32 *) (tmpbuf))); tempval = *((u32 *) (tmpbuf + 4)); gfar_write(macptr+1, tempval); } /* GFAR error interrupt handler */ static irqreturn_t gfar_error(int irq, void *dev_id) { struct net_device *dev = dev_id; struct gfar_private *priv = netdev_priv(dev); /* Save ievent for future reference */ u32 events = gfar_read(&priv->regs->ievent); /* Clear IEVENT */ gfar_write(&priv->regs->ievent, events & IEVENT_ERR_MASK); /* Magic Packet is not an error. */ if ((priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) && (events & IEVENT_MAG)) events &= ~IEVENT_MAG; /* Hmm... */ if (netif_msg_rx_err(priv) || netif_msg_tx_err(priv)) printk(KERN_DEBUG "%s: error interrupt (ievent=0x%08x imask=0x%08x)\n", dev->name, events, gfar_read(&priv->regs->imask)); /* Update the error counters */ if (events & IEVENT_TXE) { dev->stats.tx_errors++; if (events & IEVENT_LC) dev->stats.tx_window_errors++; if (events & IEVENT_CRL) dev->stats.tx_aborted_errors++; if (events & IEVENT_XFUN) { if (netif_msg_tx_err(priv)) printk(KERN_DEBUG "%s: TX FIFO underrun, " "packet dropped.\n", dev->name); dev->stats.tx_dropped++; priv->extra_stats.tx_underrun++; /* Reactivate the Tx Queues */ gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT); } if (netif_msg_tx_err(priv)) printk(KERN_DEBUG "%s: Transmit Error\n", dev->name); } if (events & IEVENT_BSY) { dev->stats.rx_errors++; priv->extra_stats.rx_bsy++; gfar_receive(irq, dev_id); if (netif_msg_rx_err(priv)) printk(KERN_DEBUG "%s: busy error (rstat: %x)\n", dev->name, gfar_read(&priv->regs->rstat)); } if (events & IEVENT_BABR) { dev->stats.rx_errors++; priv->extra_stats.rx_babr++; if (netif_msg_rx_err(priv)) printk(KERN_DEBUG "%s: babbling RX error\n", dev->name); } if (events & IEVENT_EBERR) { priv->extra_stats.eberr++; if (netif_msg_rx_err(priv)) printk(KERN_DEBUG "%s: bus error\n", dev->name); } if ((events & IEVENT_RXC) && netif_msg_rx_status(priv)) printk(KERN_DEBUG "%s: control frame\n", dev->name); if (events & IEVENT_BABT) { priv->extra_stats.tx_babt++; if (netif_msg_tx_err(priv)) printk(KERN_DEBUG "%s: babbling TX error\n", dev->name); } return IRQ_HANDLED; } /* work with hotplug and coldplug */ MODULE_ALIAS("platform:fsl-gianfar"); static struct of_device_id gfar_match[] = { { .type = "network", .compatible = "gianfar", }, {}, }; /* Structure for a device driver */ static struct of_platform_driver gfar_driver = { .name = "fsl-gianfar", .match_table = gfar_match, .probe = gfar_probe, .remove = gfar_remove, .suspend = gfar_suspend, .resume = gfar_resume, }; static int __init gfar_init(void) { int err = gfar_mdio_init(); if (err) return err; err = of_register_platform_driver(&gfar_driver); if (err) gfar_mdio_exit(); return err; } static void __exit gfar_exit(void) { of_unregister_platform_driver(&gfar_driver); gfar_mdio_exit(); } module_init(gfar_init); module_exit(gfar_exit);