/* * include/linux/mfd/asic3.h * * Compaq ASIC3 headers. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * Copyright 2001 Compaq Computer Corporation. * Copyright 2007-2008 OpenedHand Ltd. */ #ifndef __ASIC3_H__ #define __ASIC3_H__ #include struct asic3_platform_data { u16 *gpio_config; unsigned int gpio_config_num; unsigned int bus_shift; unsigned int irq_base; unsigned int gpio_base; }; #define ASIC3_NUM_GPIO_BANKS 4 #define ASIC3_GPIOS_PER_BANK 16 #define ASIC3_NUM_GPIOS 64 #define ASIC3_NR_IRQS ASIC3_NUM_GPIOS + 6 #define ASIC3_TO_GPIO(gpio) (NR_BUILTIN_GPIO + (gpio)) #define ASIC3_GPIO_BANK_A 0 #define ASIC3_GPIO_BANK_B 1 #define ASIC3_GPIO_BANK_C 2 #define ASIC3_GPIO_BANK_D 3 #define ASIC3_GPIO(bank, gpio) \ ((ASIC3_GPIOS_PER_BANK * ASIC3_GPIO_BANK_##bank) + (gpio)) #define ASIC3_GPIO_bit(gpio) (1 << (gpio & 0xf)) /* All offsets below are specified with this address bus shift */ #define ASIC3_DEFAULT_ADDR_SHIFT 2 #define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg) #define ASIC3_GPIO_OFFSET(base, reg) \ (ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg) #define ASIC3_GPIO_A_BASE 0x0000 #define ASIC3_GPIO_B_BASE 0x0100 #define ASIC3_GPIO_C_BASE 0x0200 #define ASIC3_GPIO_D_BASE 0x0300 #define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4) #define ASIC3_GPIO_TO_BIT(gpio) ((gpio) - \ (ASIC3_GPIOS_PER_BANK * ((gpio) >> 4))) #define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio)) #define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100)) #define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100)) #define ASIC3_GPIO_MASK 0x00 /* R/W 0:don't mask */ #define ASIC3_GPIO_DIRECTION 0x04 /* R/W 0:input */ #define ASIC3_GPIO_OUT 0x08 /* R/W 0:output low */ #define ASIC3_GPIO_TRIGGER_TYPE 0x0c /* R/W 0:level */ #define ASIC3_GPIO_EDGE_TRIGGER 0x10 /* R/W 0:falling */ #define ASIC3_GPIO_LEVEL_TRIGGER 0x14 /* R/W 0:low level detect */ #define ASIC3_GPIO_SLEEP_MASK 0x18 /* R/W 0:don't mask in sleep mode */ #define ASIC3_GPIO_SLEEP_OUT 0x1c /* R/W level 0:low in sleep mode */ #define ASIC3_GPIO_BAT_FAULT_OUT 0x20 /* R/W level 0:low in batt_fault */ #define ASIC3_GPIO_INT_STATUS 0x24 /* R/W 0:none, 1:detect */ #define ASIC3_GPIO_ALT_FUNCTION 0x28 /* R/W 1:LED register control */ #define ASIC3_GPIO_SLEEP_CONF 0x2c /* * R/W bit 1: autosleep * 0: disable gposlpout in normal mode, * enable gposlpout in sleep mode. */ #define ASIC3_GPIO_STATUS 0x30 /* R Pin status */ /* * ASIC3 GPIO config * * Bits 0..6 gpio number * Bits 7..13 Alternate function * Bit 14 Direction * Bit 15 Initial value * */ #define ASIC3_CONFIG_GPIO_PIN(config) ((config) & 0x7f) #define ASIC3_CONFIG_GPIO_ALT(config) (((config) & (0x7f << 7)) >> 7) #define ASIC3_CONFIG_GPIO_DIR(config) ((config & (1 << 14)) >> 14) #define ASIC3_CONFIG_GPIO_INIT(config) ((config & (1 << 15)) >> 15) #define ASIC3_CONFIG_GPIO(gpio, alt, dir, init) (((gpio) & 0x7f) \ | (((alt) & 0x7f) << 7) | (((dir) & 0x1) << 14) \ | (((init) & 0x1) << 15)) #define ASIC3_CONFIG_GPIO_DEFAULT(gpio, dir, init) \ ASIC3_CONFIG_GPIO((gpio), 0, (dir), (init)) #define ASIC3_CONFIG_GPIO_DEFAULT_OUT(gpio, init) \ ASIC3_CONFIG_GPIO((gpio), 0, 1, (init)) /* * Alternate functions */ #define ASIC3_GPIOA11_PWM0 ASIC3_CONFIG_GPIO(11, 1, 1, 0) #define ASIC3_GPIOA12_PWM1 ASIC3_CONFIG_GPIO(12, 1, 1, 0) #define ASIC3_GPIOA15_CONTROL_CX ASIC3_CONFIG_GPIO(15, 1, 1, 0) #define ASIC3_GPIOC0_LED0 ASIC3_CONFIG_GPIO(32, 1, 1, 0) #define ASIC3_GPIOC1_LED1 ASIC3_CONFIG_GPIO(33, 1, 1, 0) #define ASIC3_GPIOC2_LED2 ASIC3_CONFIG_GPIO(34, 1, 1, 0) #define ASIC3_GPIOC3_SPI_RXD ASIC3_CONFIG_GPIO(35, 1, 0, 0) #define ASIC3_GPIOC4_CF_nCD ASIC3_CONFIG_GPIO(36, 1, 0, 0) #define ASIC3_GPIOC4_SPI_TXD ASIC3_CONFIG_GPIO(36, 1, 1, 0) #define ASIC3_GPIOC5_SPI_CLK ASIC3_CONFIG_GPIO(37, 1, 1, 0) #define ASIC3_GPIOC5_nCIOW ASIC3_CONFIG_GPIO(37, 1, 1, 0) #define ASIC3_GPIOC6_nCIOR ASIC3_CONFIG_GPIO(38, 1, 1, 0) #define ASIC3_GPIOC7_nPCE_1 ASIC3_CONFIG_GPIO(39, 1, 0, 0) #define ASIC3_GPIOC8_nPCE_2 ASIC3_CONFIG_GPIO(40, 1, 0, 0) #define ASIC3_GPIOC9_nPOE ASIC3_CONFIG_GPIO(41, 1, 0, 0) #define ASIC3_GPIOC10_nPWE ASIC3_CONFIG_GPIO(42, 1, 0, 0) #define ASIC3_GPIOC11_PSKTSEL ASIC3_CONFIG_GPIO(43, 1, 0, 0) #define ASIC3_GPIOC12_nPREG ASIC3_CONFIG_GPIO(44, 1, 0, 0) #define ASIC3_GPIOC13_nPWAIT ASIC3_CONFIG_GPIO(45, 1, 1, 0) #define ASIC3_GPIOC14_nPIOIS16 ASIC3_CONFIG_GPIO(46, 1, 1, 0) #define ASIC3_GPIOC15_nPIOR ASIC3_CONFIG_GPIO(47, 1, 0, 0) #define ASIC3_GPIOD11_nCIOIS16 ASIC3_CONFIG_GPIO(59, 1, 0, 0) #define ASIC3_GPIOD12_nCWAIT ASIC3_CONFIG_GPIO(60, 1, 0, 0) #define ASIC3_GPIOD15_nPIOW ASIC3_CONFIG_GPIO(63, 1, 0, 0) #define ASIC3_SPI_Base 0x0400 #define ASIC3_SPI_Control 0x0000 #define ASIC3_SPI_TxData 0x0004 #define ASIC3_SPI_RxData 0x0008 #define ASIC3_SPI_Int 0x000c #define ASIC3_SPI_Status 0x0010 #define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */ #define ASIC3_PWM_0_Base 0x0500 #define ASIC3_PWM_1_Base 0x0600 #define ASIC3_PWM_TimeBase 0x0000 #define ASIC3_PWM_PeriodTime 0x0004 #define ASIC3_PWM_DutyTime 0x0008 #define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */ #define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */ #define ASIC3_LED_0_Base 0x0700 #define ASIC3_LED_1_Base 0x0800 #define ASIC3_LED_2_Base 0x0900 #define ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */ #define ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */ #define ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */ #define ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */ /* LED TimeBase bits - match ASIC2 */ #define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */ /* Note: max = 5 on hx4700 */ /* 0: maximum time base */ /* 1: maximum time base / 2 */ /* n: maximum time base / 2^n */ #define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */ #define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */ #define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */ #define ASIC3_CLOCK_BASE 0x0A00 #define ASIC3_CLOCK_CDEX 0x00 #define ASIC3_CLOCK_SEL 0x04 #define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */ #define CLOCK_CDEX_SOURCE0 (1 << 0) #define CLOCK_CDEX_SOURCE1 (1 << 1) #define CLOCK_CDEX_SPI (1 << 2) #define CLOCK_CDEX_OWM (1 << 3) #define CLOCK_CDEX_PWM0 (1 << 4) #define CLOCK_CDEX_PWM1 (1 << 5) #define CLOCK_CDEX_LED0 (1 << 6) #define CLOCK_CDEX_LED1 (1 << 7) #define CLOCK_CDEX_LED2 (1 << 8) /* Clocks settings: 1 for 24.576 MHz, 0 for 12.288Mhz */ #define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source */ #define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source ctrl */ #define CLOCK_CDEX_SMBUS (1 << 11) #define CLOCK_CDEX_CONTROL_CX (1 << 12) #define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */ #define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */ #define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select */ #define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select */ /* R/W: INT clock source control (32.768 kHz) */ #define CLOCK_SEL_CX (1 << 2) #define ASIC3_INTR_BASE 0x0B00 #define ASIC3_INTR_INT_MASK 0x00 /* Interrupt mask control */ #define ASIC3_INTR_P_INT_STAT 0x04 /* Peripheral interrupt status */ #define ASIC3_INTR_INT_CPS 0x08 /* Interrupt timer clock pre-scale */ #define ASIC3_INTR_INT_TBS 0x0c /* Interrupt timer set */ #define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */ #define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */ #define ASIC3_INTMASK_MASK0 (1 << 2) #define ASIC3_INTMASK_MASK1 (1 << 3) #define ASIC3_INTMASK_MASK2 (1 << 4) #define ASIC3_INTMASK_MASK3 (1 << 5) #define ASIC3_INTMASK_MASK4 (1 << 6) #define ASIC3_INTMASK_MASK5 (1 << 7) #define ASIC3_INTR_PERIPHERAL_A (1 << 0) #define ASIC3_INTR_PERIPHERAL_B (1 << 1) #define ASIC3_INTR_PERIPHERAL_C (1 << 2) #define ASIC3_INTR_PERIPHERAL_D (1 << 3) #define ASIC3_INTR_LED0 (1 << 4) #define ASIC3_INTR_LED1 (1 << 5) #define ASIC3_INTR_LED2 (1 << 6) #define ASIC3_INTR_SPI (1 << 7) #define ASIC3_INTR_SMBUS (1 << 8) #define ASIC3_INTR_OWM (1 << 9) #define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */ #define ASIC3_INTR_CPS_SET (1 << 4) /* Time base enable */ /* Basic control of the SD ASIC */ #define ASIC3_SDHWCTRL_Base 0x0E00 #define ASIC3_SDHWCTRL_SDConf 0x00 #define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */ #define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */ #define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */ #define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* SD card detection: 0:low */ /* SD card write protection: 0=high */ #define ASIC3_SDHWCTRL_LEVWP (1 << 4) #define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 0=disable */ /* SD card power supply ctrl 1=enable */ #define ASIC3_SDHWCTRL_SDPWR (1 << 6) #define ASIC3_EXTCF_Base 0x1100 #define ASIC3_EXTCF_Select 0x00 #define ASIC3_EXTCF_Reset 0x04 #define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */ #define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */ #define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */ #define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */ #define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */ #define ASIC3_EXTCF_OWM_RESET (1 << 6) /* ?? used by OWM and CF */ #define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state */ #define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state */ #define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */ #define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */ #define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */ #define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */ #define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14) #define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */ /********************************************* * The Onewire interface registers * * OWM_CMD * OWM_DAT * OWM_INTR * OWM_INTEN * OWM_CLKDIV * *********************************************/ #define ASIC3_OWM_Base 0xC00 #define ASIC3_OWM_CMD 0x00 #define ASIC3_OWM_DAT 0x04 #define ASIC3_OWM_INTR 0x08 #define ASIC3_OWM_INTEN 0x0C #define ASIC3_OWM_CLKDIV 0x10 #define ASIC3_OWM_CMD_ONEWR (1 << 0) #define ASIC3_OWM_CMD_SRA (1 << 1) #define ASIC3_OWM_CMD_DQO (1 << 2) #define ASIC3_OWM_CMD_DQI (1 << 3) #define ASIC3_OWM_INTR_PD (1 << 0) #define ASIC3_OWM_INTR_PDR (1 << 1) #define ASIC3_OWM_INTR_TBE (1 << 2) #define ASIC3_OWM_INTR_TEMP (1 << 3) #define ASIC3_OWM_INTR_RBF (1 << 4) #define ASIC3_OWM_INTEN_EPD (1 << 0) #define ASIC3_OWM_INTEN_IAS (1 << 1) #define ASIC3_OWM_INTEN_ETBE (1 << 2) #define ASIC3_OWM_INTEN_ETMT (1 << 3) #define ASIC3_OWM_INTEN_ERBF (1 << 4) #define ASIC3_OWM_CLKDIV_PRE (3 << 0) /* two bits wide at bit 0 */ #define ASIC3_OWM_CLKDIV_DIV (7 << 2) /* 3 bits wide at bit 2 */ /***************************************************************************** * The SD configuration registers are at a completely different location * in memory. They are divided into three sets of registers: * * SD_CONFIG Core configuration register * SD_CTRL Control registers for SD operations * SDIO_CTRL Control registers for SDIO operations * *****************************************************************************/ #define ASIC3_SD_CONFIG_Base 0x0400 /* Assumes 32 bit addressing */ #define ASIC3_SD_CONFIG_Command 0x08 /* R/W: Command */ /* [0:8] SD Control Register Base Address */ #define ASIC3_SD_CONFIG_Addr0 0x20 /* [9:31] SD Control Register Base Address */ #define ASIC3_SD_CONFIG_Addr1 0x24 /* R/O: interrupt assigned to pin */ #define ASIC3_SD_CONFIG_IntPin 0x78 /* * Set to 0x1f to clock SD controller, 0 otherwise. * At 0x82 - Gated Clock Ctrl */ #define ASIC3_SD_CONFIG_ClkStop 0x80 /* Control clock of SD controller */ #define ASIC3_SD_CONFIG_ClockMode 0x84 #define ASIC3_SD_CONFIG_SDHC_PinStatus 0x88 /* R/0: SD pins status */ #define ASIC3_SD_CONFIG_SDHC_Power1 0x90 /* Power1 - manual pwr ctrl */ /* auto power up after card inserted */ #define ASIC3_SD_CONFIG_SDHC_Power2 0x92 /* auto power down when card removed */ #define ASIC3_SD_CONFIG_SDHC_Power3 0x94 #define ASIC3_SD_CONFIG_SDHC_CardDetect 0x98 #define ASIC3_SD_CONFIG_SDHC_Slot 0xA0 /* R/O: support slot number */ #define ASIC3_SD_CONFIG_SDHC_ExtGateClk1 0x1E0 /* Not used */ #define ASIC3_SD_CONFIG_SDHC_ExtGateClk2 0x1E2 /* Not used*/ /* GPIO Output Reg. , at 0x1EA - GPIO Output Enable Reg. */ #define ASIC3_SD_CONFIG_SDHC_GPIO_OutAndEnable 0x1E8 #define ASIC3_SD_CONFIG_SDHC_GPIO_Status 0x1EC /* GPIO Status Reg. */ /* Bit 1: double buffer/single buffer */ #define ASIC3_SD_CONFIG_SDHC_ExtGateClk3 0x1F0 /* Memory access enable (set to 1 to access SD Controller) */ #define SD_CONFIG_COMMAND_MAE (1<<1) #define SD_CONFIG_CLK_ENABLE_ALL 0x1f #define SD_CONFIG_POWER1_PC_33V 0x0200 /* Set for 3.3 volts */ #define SD_CONFIG_POWER1_PC_OFF 0x0000 /* Turn off power */ /* two bits - number of cycles for card detection */ #define SD_CONFIG_CARDDETECTMODE_CLK ((x) & 0x3) #define ASIC3_SD_CTRL_Base 0x1000 #define ASIC3_SD_CTRL_Cmd 0x00 #define ASIC3_SD_CTRL_Arg0 0x08 #define ASIC3_SD_CTRL_Arg1 0x0C #define ASIC3_SD_CTRL_StopInternal 0x10 #define ASIC3_SD_CTRL_TransferSectorCount 0x14 #define ASIC3_SD_CTRL_Response0 0x18 #define ASIC3_SD_CTRL_Response1 0x1C #define ASIC3_SD_CTRL_Response2 0x20 #define ASIC3_SD_CTRL_Response3 0x24 #define ASIC3_SD_CTRL_Response4 0x28 #define ASIC3_SD_CTRL_Response5 0x2C #define ASIC3_SD_CTRL_Response6 0x30 #define ASIC3_SD_CTRL_Response7 0x34 #define ASIC3_SD_CTRL_CardStatus 0x38 #define ASIC3_SD_CTRL_BufferCtrl 0x3C #define ASIC3_SD_CTRL_IntMaskCard 0x40 #define ASIC3_SD_CTRL_IntMaskBuffer 0x44 #define ASIC3_SD_CTRL_CardClockCtrl 0x48 #define ASIC3_SD_CTRL_MemCardXferDataLen 0x4C #define ASIC3_SD_CTRL_MemCardOptionSetup 0x50 #define ASIC3_SD_CTRL_ErrorStatus0 0x58 #define ASIC3_SD_CTRL_ErrorStatus1 0x5C #define ASIC3_SD_CTRL_DataPort 0x60 #define ASIC3_SD_CTRL_TransactionCtrl 0x68 #define ASIC3_SD_CTRL_SoftwareReset 0x1C0 #define SD_CTRL_SOFTWARE_RESET_CLEAR (1<<0) #define SD_CTRL_TRANSACTIONCONTROL_SET (1<<8) #define SD_CTRL_CARDCLOCKCONTROL_FOR_SD_CARD (1<<15) #define SD_CTRL_CARDCLOCKCONTROL_ENABLE_CLOCK (1<<8) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_512 (1<<7) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_256 (1<<6) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_128 (1<<5) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_64 (1<<4) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_32 (1<<3) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_16 (1<<2) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_8 (1<<1) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_4 (1<<0) #define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_2 (0<<0) #define MEM_CARD_OPTION_REQUIRED 0x000e #define MEM_CARD_OPTION_DATA_RESPONSE_TIMEOUT(x) (((x) & 0x0f) << 4) #define MEM_CARD_OPTION_C2_MODULE_NOT_PRESENT (1<<14) #define MEM_CARD_OPTION_DATA_XFR_WIDTH_1 (1<<15) #define MEM_CARD_OPTION_DATA_XFR_WIDTH_4 0 #define SD_CTRL_COMMAND_INDEX(x) ((x) & 0x3f) #define SD_CTRL_COMMAND_TYPE_CMD (0 << 6) #define SD_CTRL_COMMAND_TYPE_ACMD (1 << 6) #define SD_CTRL_COMMAND_TYPE_AUTHENTICATION (2 << 6) #define SD_CTRL_COMMAND_RESPONSE_TYPE_NORMAL (0 << 8) #define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1 (4 << 8) #define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1B (5 << 8) #define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R2 (6 << 8) #define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R3 (7 << 8) #define SD_CTRL_COMMAND_DATA_PRESENT (1 << 11) #define SD_CTRL_COMMAND_TRANSFER_READ (1 << 12) #define SD_CTRL_COMMAND_TRANSFER_WRITE (0 << 12) #define SD_CTRL_COMMAND_MULTI_BLOCK (1 << 13) #define SD_CTRL_COMMAND_SECURITY_CMD (1 << 14) #define SD_CTRL_STOP_INTERNAL_ISSSUE_CMD12 (1 << 0) #define SD_CTRL_STOP_INTERNAL_AUTO_ISSUE_CMD12 (1 << 8) #define SD_CTRL_CARDSTATUS_RESPONSE_END (1 << 0) #define SD_CTRL_CARDSTATUS_RW_END (1 << 2) #define SD_CTRL_CARDSTATUS_CARD_REMOVED_0 (1 << 3) #define SD_CTRL_CARDSTATUS_CARD_INSERTED_0 (1 << 4) #define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_0 (1 << 5) #define SD_CTRL_CARDSTATUS_WRITE_PROTECT (1 << 7) #define SD_CTRL_CARDSTATUS_CARD_REMOVED_3 (1 << 8) #define SD_CTRL_CARDSTATUS_CARD_INSERTED_3 (1 << 9) #define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_3 (1 << 10) #define SD_CTRL_BUFFERSTATUS_CMD_INDEX_ERROR (1 << 0) #define SD_CTRL_BUFFERSTATUS_CRC_ERROR (1 << 1) #define SD_CTRL_BUFFERSTATUS_STOP_BIT_END_ERROR (1 << 2) #define SD_CTRL_BUFFERSTATUS_DATA_TIMEOUT (1 << 3) #define SD_CTRL_BUFFERSTATUS_BUFFER_OVERFLOW (1 << 4) #define SD_CTRL_BUFFERSTATUS_BUFFER_UNDERFLOW (1 << 5) #define SD_CTRL_BUFFERSTATUS_CMD_TIMEOUT (1 << 6) #define SD_CTRL_BUFFERSTATUS_UNK7 (1 << 7) #define SD_CTRL_BUFFERSTATUS_BUFFER_READ_ENABLE (1 << 8) #define SD_CTRL_BUFFERSTATUS_BUFFER_WRITE_ENABLE (1 << 9) #define SD_CTRL_BUFFERSTATUS_ILLEGAL_FUNCTION (1 << 13) #define SD_CTRL_BUFFERSTATUS_CMD_BUSY (1 << 14) #define SD_CTRL_BUFFERSTATUS_ILLEGAL_ACCESS (1 << 15) #define SD_CTRL_INTMASKCARD_RESPONSE_END (1 << 0) #define SD_CTRL_INTMASKCARD_RW_END (1 << 2) #define SD_CTRL_INTMASKCARD_CARD_REMOVED_0 (1 << 3) #define SD_CTRL_INTMASKCARD_CARD_INSERTED_0 (1 << 4) #define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_0 (1 << 5) #define SD_CTRL_INTMASKCARD_UNK6 (1 << 6) #define SD_CTRL_INTMASKCARD_WRITE_PROTECT (1 << 7) #define SD_CTRL_INTMASKCARD_CARD_REMOVED_3 (1 << 8) #define SD_CTRL_INTMASKCARD_CARD_INSERTED_3 (1 << 9) #define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_3 (1 << 10) #define SD_CTRL_INTMASKBUFFER_CMD_INDEX_ERROR (1 << 0) #define SD_CTRL_INTMASKBUFFER_CRC_ERROR (1 << 1) #define SD_CTRL_INTMASKBUFFER_STOP_BIT_END_ERROR (1 << 2) #define SD_CTRL_INTMASKBUFFER_DATA_TIMEOUT (1 << 3) #define SD_CTRL_INTMASKBUFFER_BUFFER_OVERFLOW (1 << 4) #define SD_CTRL_INTMASKBUFFER_BUFFER_UNDERFLOW (1 << 5) #define SD_CTRL_INTMASKBUFFER_CMD_TIMEOUT (1 << 6) #define SD_CTRL_INTMASKBUFFER_UNK7 (1 << 7) #define SD_CTRL_INTMASKBUFFER_BUFFER_READ_ENABLE (1 << 8) #define SD_CTRL_INTMASKBUFFER_BUFFER_WRITE_ENABLE (1 << 9) #define SD_CTRL_INTMASKBUFFER_ILLEGAL_FUNCTION (1 << 13) #define SD_CTRL_INTMASKBUFFER_CMD_BUSY (1 << 14) #define SD_CTRL_INTMASKBUFFER_ILLEGAL_ACCESS (1 << 15) #define SD_CTRL_DETAIL0_RESPONSE_CMD_ERROR (1 << 0) #define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 2) #define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_CMD12 (1 << 3) #define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_READ_DATA (1 << 4) #define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_WRITE_CRC_STATUS (1 << 5) #define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 8) #define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_CMD12 (1 << 9) #define SD_CTRL_DETAIL0_CRC_ERROR_FOR_READ_DATA (1 << 10) #define SD_CTRL_DETAIL0_CRC_ERROR_FOR_WRITE_CMD (1 << 11) #define SD_CTRL_DETAIL1_NO_CMD_RESPONSE (1 << 0) #define SD_CTRL_DETAIL1_TIMEOUT_READ_DATA (1 << 4) #define SD_CTRL_DETAIL1_TIMEOUT_CRS_STATUS (1 << 5) #define SD_CTRL_DETAIL1_TIMEOUT_CRC_BUSY (1 << 6) #define ASIC3_SDIO_CTRL_Base 0x1200 #define ASIC3_SDIO_CTRL_Cmd 0x00 #define ASIC3_SDIO_CTRL_CardPortSel 0x04 #define ASIC3_SDIO_CTRL_Arg0 0x08 #define ASIC3_SDIO_CTRL_Arg1 0x0C #define ASIC3_SDIO_CTRL_TransferBlockCount 0x14 #define ASIC3_SDIO_CTRL_Response0 0x18 #define ASIC3_SDIO_CTRL_Response1 0x1C #define ASIC3_SDIO_CTRL_Response2 0x20 #define ASIC3_SDIO_CTRL_Response3 0x24 #define ASIC3_SDIO_CTRL_Response4 0x28 #define ASIC3_SDIO_CTRL_Response5 0x2C #define ASIC3_SDIO_CTRL_Response6 0x30 #define ASIC3_SDIO_CTRL_Response7 0x34 #define ASIC3_SDIO_CTRL_CardStatus 0x38 #define ASIC3_SDIO_CTRL_BufferCtrl 0x3C #define ASIC3_SDIO_CTRL_IntMaskCard 0x40 #define ASIC3_SDIO_CTRL_IntMaskBuffer 0x44 #define ASIC3_SDIO_CTRL_CardXferDataLen 0x4C #define ASIC3_SDIO_CTRL_CardOptionSetup 0x50 #define ASIC3_SDIO_CTRL_ErrorStatus0 0x54 #define ASIC3_SDIO_CTRL_ErrorStatus1 0x58 #define ASIC3_SDIO_CTRL_DataPort 0x60 #define ASIC3_SDIO_CTRL_TransactionCtrl 0x68 #define ASIC3_SDIO_CTRL_CardIntCtrl 0x6C #define ASIC3_SDIO_CTRL_ClocknWaitCtrl 0x70 #define ASIC3_SDIO_CTRL_HostInformation 0x74 #define ASIC3_SDIO_CTRL_ErrorCtrl 0x78 #define ASIC3_SDIO_CTRL_LEDCtrl 0x7C #define ASIC3_SDIO_CTRL_SoftwareReset 0x1C0 #define ASIC3_MAP_SIZE 0x2000 #endif /* __ASIC3_H__ */