1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
/*
* include/asm-arm/arch-ixp2000/platform.h
*
* Various bits of code used by platform-level code.
*
* Author: Deepak Saxena <dsaxena@plexity.net>
*
* Copyright 2004 (c) MontaVista Software, Inc.
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#ifndef __ASSEMBLY__
/*
* The IXP2400 B0 silicon contains an erratum (#66) that causes writes
* to on-chip I/O register to not complete fully. What this means is
* that if you have a write to on-chip I/O followed by a back-to-back
* read or write, the first write will happen twice. OR...if it's
* not a back-to-back transaction, the read or write will generate
* incorrect data.
*
* The official work around for this is to set the on-chip I/O regions
* as XCB=101 and then force a read-back from the register.
*
*/
#if defined(CONFIG_ARCH_ENP2611) || defined(CONFIG_ARCH_IXDP2400) || defined(CONFIG_ARCH_IXDP2401)
#include <asm/system.h> /* Pickup local_irq_ functions */
static inline void ixp2000_reg_write(volatile unsigned long *reg, unsigned long val)
{
volatile unsigned long dummy;
unsigned long flags;
local_irq_save(flags);
*reg = val;
barrier();
dummy = *reg;
local_irq_restore(flags);
}
#else
#define ixp2000_reg_write(reg, val) (*reg = val)
#endif /* IXDP2400 || IXDP2401 */
/*
* Boards may multiplex different devices on the 2nd channel of
* the slowport interface that each need different configuration
* settings. For example, the IXDP2400 uses channel 2 on the interface
* to access the CPLD, the switch fabric card, and the media card. Each
* one needs a different mode so drivers must save/restore the mode
* before and after each operation.
*
* acquire_slowport(&your_config);
* ...
* do slowport operations
* ...
* release_slowport();
*
* Note that while you have the slowport, you are holding a spinlock,
* so your code should be written as if you explicitly acquired a lock.
*
* The configuration only affects device 2 on the slowport, so the
* MTD map driver does not acquire/release the slowport.
*/
struct slowport_cfg {
unsigned long CCR; /* Clock divide */
unsigned long WTC; /* Write Timing Control */
unsigned long RTC; /* Read Timing Control */
unsigned long PCR; /* Protocol Control Register */
unsigned long ADC; /* Address/Data Width Control */
};
void ixp2000_acquire_slowport(struct slowport_cfg *, struct slowport_cfg *);
void ixp2000_release_slowport(struct slowport_cfg *);
/*
* IXP2400 A0/A1 and IXP2800 A0/A1/A2 have broken slowport that requires
* tweaking of addresses in the MTD driver.
*/
static inline unsigned ixp2000_has_broken_slowport(void)
{
unsigned long id = *IXP2000_PROD_ID;
unsigned long id_prod = id & (IXP2000_MAJ_PROD_TYPE_MASK |
IXP2000_MIN_PROD_TYPE_MASK);
return (((id_prod ==
/* fixed in IXP2400-B0 */
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
IXP2000_MIN_PROD_TYPE_IXP2400)) &&
((id & IXP2000_MAJ_REV_MASK) == 0)) ||
((id_prod ==
/* fixed in IXP2800-B0 */
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
IXP2000_MIN_PROD_TYPE_IXP2800)) &&
((id & IXP2000_MAJ_REV_MASK) == 0)) ||
((id_prod ==
/* fixed in IXP2850-B0 */
(IXP2000_MAJ_PROD_TYPE_IXP2000 |
IXP2000_MIN_PROD_TYPE_IXP2850)) &&
((id & IXP2000_MAJ_REV_MASK) == 0)));
}
static inline unsigned int ixp2000_has_flash(void)
{
return ((*IXP2000_STRAP_OPTIONS) & (CFG_BOOT_PROM));
}
static inline unsigned int ixp2000_is_pcimaster(void)
{
return ((*IXP2000_STRAP_OPTIONS) & (CFG_PCI_BOOT_HOST));
}
void ixp2000_map_io(void);
void ixp2000_init_irq(void);
void ixp2000_init_time(unsigned long);
unsigned long ixp2000_gettimeoffset(void);
struct pci_sys_data;
u32 *ixp2000_pci_config_addr(unsigned int bus, unsigned int devfn, int where);
void ixp2000_pci_preinit(void);
int ixp2000_pci_setup(int, struct pci_sys_data*);
struct pci_bus* ixp2000_pci_scan_bus(int, struct pci_sys_data*);
int ixp2000_pci_read_config(struct pci_bus*, unsigned int, int, int, u32 *);
int ixp2000_pci_write_config(struct pci_bus*, unsigned int, int, int, u32);
/*
* Several of the IXP2000 systems have banked flash so we need to extend the
* flash_platform_data structure with some private pointers
*/
struct ixp2000_flash_data {
struct flash_platform_data *platform_data;
int nr_banks;
unsigned long (*bank_setup)(unsigned long);
};
struct ixp2000_i2c_pins {
unsigned long sda_pin;
unsigned long scl_pin;
};
#endif /* !__ASSEMBLY__ */
|
