aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorMichael Albaugh <michael.albaugh@qlogic.com>2007-05-16 15:45:09 -0700
committerRoland Dreier <rolandd@cisco.com>2007-07-09 20:12:25 -0700
commit82466f00ec6ef0a5ca7ea8991c731af2ec561c7d (patch)
tree48fcc8f78e6df67130e8c70b160fea42aeff79ca
parenta024291b367f98188f4da4a66a9f2f40a2163efb (diff)
IB/ipath: Support blinking LEDs with an led_override file
When we want to find an InfiniPath HCA in a rack of nodes, it is often expeditious to blink the status LEDs via a userspace /sys file. A write-only led_override "file" is published per device. Writes to this file are interpreted as (string form) numbers, and the resulting value sent to ipath_set_led_override(). The upper eight bits are interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom two 4-bit values are alternately (D0..3, then D4..7) used by the board-specific LED-setting function to override the normal state. Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
-rw-r--r--drivers/infiniband/hw/ipath/ipath_driver.c92
-rw-r--r--drivers/infiniband/hw/ipath/ipath_iba6110.c10
-rw-r--r--drivers/infiniband/hw/ipath/ipath_iba6120.c10
-rw-r--r--drivers/infiniband/hw/ipath/ipath_kernel.h19
-rw-r--r--drivers/infiniband/hw/ipath/ipath_sysfs.c19
5 files changed, 149 insertions, 1 deletions
diff --git a/drivers/infiniband/hw/ipath/ipath_driver.c b/drivers/infiniband/hw/ipath/ipath_driver.c
index e3a22320971..09759328658 100644
--- a/drivers/infiniband/hw/ipath/ipath_driver.c
+++ b/drivers/infiniband/hw/ipath/ipath_driver.c
@@ -1846,6 +1846,87 @@ void ipath_write_kreg_port(const struct ipath_devdata *dd, ipath_kreg regno,
ipath_write_kreg(dd, where, value);
}
+/*
+ * Following deal with the "obviously simple" task of overriding the state
+ * of the LEDS, which normally indicate link physical and logical status.
+ * The complications arise in dealing with different hardware mappings
+ * and the board-dependent routine being called from interrupts.
+ * and then there's the requirement to _flash_ them.
+ */
+#define LED_OVER_FREQ_SHIFT 8
+#define LED_OVER_FREQ_MASK (0xFF<<LED_OVER_FREQ_SHIFT)
+/* Below is "non-zero" to force override, but both actual LEDs are off */
+#define LED_OVER_BOTH_OFF (8)
+
+void ipath_run_led_override(unsigned long opaque)
+{
+ struct ipath_devdata *dd = (struct ipath_devdata *)opaque;
+ int timeoff;
+ int pidx;
+ u64 lstate, ltstate, val;
+
+ if (!(dd->ipath_flags & IPATH_INITTED))
+ return;
+
+ pidx = dd->ipath_led_override_phase++ & 1;
+ dd->ipath_led_override = dd->ipath_led_override_vals[pidx];
+ timeoff = dd->ipath_led_override_timeoff;
+
+ /*
+ * below potentially restores the LED values per current status,
+ * should also possibly setup the traffic-blink register,
+ * but leave that to per-chip functions.
+ */
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcstatus);
+ ltstate = (val >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
+ INFINIPATH_IBCS_LINKTRAININGSTATE_MASK;
+ lstate = (val >> INFINIPATH_IBCS_LINKSTATE_SHIFT) &
+ INFINIPATH_IBCS_LINKSTATE_MASK;
+
+ dd->ipath_f_setextled(dd, lstate, ltstate);
+ mod_timer(&dd->ipath_led_override_timer, jiffies + timeoff);
+}
+
+void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val)
+{
+ int timeoff, freq;
+
+ if (!(dd->ipath_flags & IPATH_INITTED))
+ return;
+
+ /* First check if we are blinking. If not, use 1HZ polling */
+ timeoff = HZ;
+ freq = (val & LED_OVER_FREQ_MASK) >> LED_OVER_FREQ_SHIFT;
+
+ if (freq) {
+ /* For blink, set each phase from one nybble of val */
+ dd->ipath_led_override_vals[0] = val & 0xF;
+ dd->ipath_led_override_vals[1] = (val >> 4) & 0xF;
+ timeoff = (HZ << 4)/freq;
+ } else {
+ /* Non-blink set both phases the same. */
+ dd->ipath_led_override_vals[0] = val & 0xF;
+ dd->ipath_led_override_vals[1] = val & 0xF;
+ }
+ dd->ipath_led_override_timeoff = timeoff;
+
+ /*
+ * If the timer has not already been started, do so. Use a "quick"
+ * timeout so the function will be called soon, to look at our request.
+ */
+ if (atomic_inc_return(&dd->ipath_led_override_timer_active) == 1) {
+ /* Need to start timer */
+ init_timer(&dd->ipath_led_override_timer);
+ dd->ipath_led_override_timer.function =
+ ipath_run_led_override;
+ dd->ipath_led_override_timer.data = (unsigned long) dd;
+ dd->ipath_led_override_timer.expires = jiffies + 1;
+ add_timer(&dd->ipath_led_override_timer);
+ } else {
+ atomic_dec(&dd->ipath_led_override_timer_active);
+ }
+}
+
/**
* ipath_shutdown_device - shut down a device
* @dd: the infinipath device
@@ -1909,7 +1990,6 @@ void ipath_shutdown_device(struct ipath_devdata *dd)
* Turn the LEDs off explictly for the same reason.
*/
dd->ipath_f_quiet_serdes(dd);
- dd->ipath_f_setextled(dd, 0, 0);
if (dd->ipath_stats_timer_active) {
del_timer_sync(&dd->ipath_stats_timer);
@@ -2085,6 +2165,16 @@ int ipath_reset_device(int unit)
goto bail;
}
+ if (atomic_read(&dd->ipath_led_override_timer_active)) {
+ /* Need to stop LED timer, _then_ shut off LEDs */
+ del_timer_sync(&dd->ipath_led_override_timer);
+ atomic_set(&dd->ipath_led_override_timer_active, 0);
+ }
+
+ /* Shut off LEDs after we are sure timer is not running */
+ dd->ipath_led_override = LED_OVER_BOTH_OFF;
+ dd->ipath_f_setextled(dd, 0, 0);
+
dev_info(&dd->pcidev->dev, "Reset on unit %u requested\n", unit);
if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) {
diff --git a/drivers/infiniband/hw/ipath/ipath_iba6110.c b/drivers/infiniband/hw/ipath/ipath_iba6110.c
index ba73dd0a06c..4372c6c50ff 100644
--- a/drivers/infiniband/hw/ipath/ipath_iba6110.c
+++ b/drivers/infiniband/hw/ipath/ipath_iba6110.c
@@ -1065,6 +1065,16 @@ static void ipath_setup_ht_setextled(struct ipath_devdata *dd,
if (ipath_diag_inuse)
return;
+ /* Allow override of LED display for, e.g. Locating system in rack */
+ if (dd->ipath_led_override) {
+ ltst = (dd->ipath_led_override & IPATH_LED_PHYS)
+ ? INFINIPATH_IBCS_LT_STATE_LINKUP
+ : INFINIPATH_IBCS_LT_STATE_DISABLED;
+ lst = (dd->ipath_led_override & IPATH_LED_LOG)
+ ? INFINIPATH_IBCS_L_STATE_ACTIVE
+ : INFINIPATH_IBCS_L_STATE_DOWN;
+ }
+
/*
* start by setting both LED control bits to off, then turn
* on the appropriate bit(s).
diff --git a/drivers/infiniband/hw/ipath/ipath_iba6120.c b/drivers/infiniband/hw/ipath/ipath_iba6120.c
index 4e2e3dfeb2c..bcb70d67dbb 100644
--- a/drivers/infiniband/hw/ipath/ipath_iba6120.c
+++ b/drivers/infiniband/hw/ipath/ipath_iba6120.c
@@ -797,6 +797,16 @@ static void ipath_setup_pe_setextled(struct ipath_devdata *dd, u64 lst,
if (ipath_diag_inuse)
return;
+ /* Allow override of LED display for, e.g. Locating system in rack */
+ if (dd->ipath_led_override) {
+ ltst = (dd->ipath_led_override & IPATH_LED_PHYS)
+ ? INFINIPATH_IBCS_LT_STATE_LINKUP
+ : INFINIPATH_IBCS_LT_STATE_DISABLED;
+ lst = (dd->ipath_led_override & IPATH_LED_LOG)
+ ? INFINIPATH_IBCS_L_STATE_ACTIVE
+ : INFINIPATH_IBCS_L_STATE_DOWN;
+ }
+
extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
INFINIPATH_EXTC_LED2PRIPORT_ON);
diff --git a/drivers/infiniband/hw/ipath/ipath_kernel.h b/drivers/infiniband/hw/ipath/ipath_kernel.h
index 12194f3dd8c..2f39db7df31 100644
--- a/drivers/infiniband/hw/ipath/ipath_kernel.h
+++ b/drivers/infiniband/hw/ipath/ipath_kernel.h
@@ -575,6 +575,16 @@ struct ipath_devdata {
u16 ipath_gpio_scl_num;
u64 ipath_gpio_sda;
u64 ipath_gpio_scl;
+
+ /* used to override LED behavior */
+ u8 ipath_led_override; /* Substituted for normal value, if non-zero */
+ u16 ipath_led_override_timeoff; /* delta to next timer event */
+ u8 ipath_led_override_vals[2]; /* Alternates per blink-frame */
+ u8 ipath_led_override_phase; /* Just counts, LSB picks from vals[] */
+ atomic_t ipath_led_override_timer_active;
+ /* Used to flash LEDs in override mode */
+ struct timer_list ipath_led_override_timer;
+
};
/* Private data for file operations */
@@ -717,6 +727,15 @@ u64 ipath_snap_cntr(struct ipath_devdata *, ipath_creg);
void ipath_disarm_senderrbufs(struct ipath_devdata *, int);
/*
+ * Set LED override, only the two LSBs have "public" meaning, but
+ * any non-zero value substitutes them for the Link and LinkTrain
+ * LED states.
+ */
+#define IPATH_LED_PHYS 1 /* Physical (linktraining) GREEN LED */
+#define IPATH_LED_LOG 2 /* Logical (link) YELLOW LED */
+void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val);
+
+/*
* number of words used for protocol header if not set by ipath_userinit();
*/
#define IPATH_DFLT_RCVHDRSIZE 9
diff --git a/drivers/infiniband/hw/ipath/ipath_sysfs.c b/drivers/infiniband/hw/ipath/ipath_sysfs.c
index 4dc398d5e01..17ec1457172 100644
--- a/drivers/infiniband/hw/ipath/ipath_sysfs.c
+++ b/drivers/infiniband/hw/ipath/ipath_sysfs.c
@@ -596,6 +596,23 @@ bail:
return ret;
}
+static ssize_t store_led_override(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf,
+ size_t count)
+{
+ struct ipath_devdata *dd = dev_get_drvdata(dev);
+ int ret;
+ u16 val;
+
+ ret = ipath_parse_ushort(buf, &val);
+ if (ret > 0)
+ ipath_set_led_override(dd, val);
+ else
+ ipath_dev_err(dd, "attempt to set invalid LED override\n");
+ return ret;
+}
+
static DRIVER_ATTR(num_units, S_IRUGO, show_num_units, NULL);
static DRIVER_ATTR(version, S_IRUGO, show_version, NULL);
@@ -625,6 +642,7 @@ static DEVICE_ATTR(status_str, S_IRUGO, show_status_str, NULL);
static DEVICE_ATTR(boardversion, S_IRUGO, show_boardversion, NULL);
static DEVICE_ATTR(unit, S_IRUGO, show_unit, NULL);
static DEVICE_ATTR(rx_pol_inv, S_IWUSR, NULL, store_rx_pol_inv);
+static DEVICE_ATTR(led_override, S_IWUSR, NULL, store_led_override);
static struct attribute *dev_attributes[] = {
&dev_attr_guid.attr,
@@ -641,6 +659,7 @@ static struct attribute *dev_attributes[] = {
&dev_attr_unit.attr,
&dev_attr_enabled.attr,
&dev_attr_rx_pol_inv.attr,
+ &dev_attr_led_override.attr,
NULL
};