MERGE-via-pending-tracking-hist-MERGE-via-stable-tracking-MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040-1232632141

pending-tracking-hist top was MERGE-via-stable-tracking-MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040-1232632141 / fdf777a63bcb59e0dfd78bfe2c6242e01f6d4eb9 ... parent commitmessage:
From: merge <null@invalid>
MERGE-via-stable-tracking-hist-MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040

stable-tracking-hist top was MERGE-via-mokopatches-tracking-fix-stray-endmenu-patch-1232632040 / 90463bfd2d5a3c8b52f6e6d71024a00e052b0ced ... parent commitmessage:
From: merge <null@invalid>
MERGE-via-mokopatches-tracking-hist-fix-stray-endmenu-patch

mokopatches-tracking-hist top was fix-stray-endmenu-patch / 3630e0be570de8057e7f8d2fe501ed353cdf34e6 ... parent commitmessage:
From: Andy Green <andy@openmoko.com>
fix-stray-endmenu.patch

Signed-off-by: Andy Green <andy@openmoko.com>

35 files changed, 975 insertions, 205 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 5aafb2e2ca7..323b47f2b52 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -7,36 +7,43 @@ choice
 
 config ARCH_AT91RM9200
 	bool "AT91RM9200"
+	select CPU_ARM920T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
 config ARCH_AT91SAM9260
 	bool "AT91SAM9260 or AT91SAM9XE"
+	select CPU_ARM926T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
 config ARCH_AT91SAM9261
 	bool "AT91SAM9261"
+	select CPU_ARM926T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
 config ARCH_AT91SAM9263
 	bool "AT91SAM9263"
+	select CPU_ARM926T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
+	select CPU_ARM926T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
 config ARCH_AT91SAM9G20
 	bool "AT91SAM9G20"
+	select CPU_ARM926T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
 config ARCH_AT91CAP9
 	bool "AT91CAP9"
+	select CPU_ARM926T
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 
@@ -235,6 +242,12 @@ config MACH_USB_A9263
 	  Select this if you are using a Calao Systems USB-A9263.
 	  <http://www.calao-systems.com>
 
+config MACH_NEOCORE926
+	bool "Adeneo NEOCORE926"
+	depends on ARCH_AT91SAM9263
+	help
+	  Select this if you are using the Adeneo Neocore 926 board.
+
 endif
 
 # ----------------------------------------------------------
@@ -302,7 +315,7 @@ comment "AT91 Board Options"
 
 config MTD_AT91_DATAFLASH_CARD
 	bool "Enable DataFlash Card support"
-	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK)
+	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK || MACH_NEOCORE926)
 	help
 	  Enable support for the DataFlash card.
 
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index cca612d97ca..c69ff237fd1 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -11,12 +11,12 @@ obj-$(CONFIG_AT91_PMC_UNIT)	+= clock.o
 
 # CPU-specific support
 obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
-obj-$(CONFIG_ARCH_AT91CAP9)	+= at91cap9.o at91sam926x_time.o at91cap9_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o  sam9_smc.o
+obj-$(CONFIG_ARCH_AT91CAP9)	+= at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
 # AT91RM9200 board-specific support
@@ -47,6 +47,7 @@ obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
 # AT91SAM9263 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
 obj-$(CONFIG_MACH_USB_A9263)	+= board-usb-a9263.o
+obj-$(CONFIG_MACH_NEOCORE926)	+= board-neocore926.o
 
 # AT91SAM9RL board-specific support
 obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
diff --git a/arch/arm/mach-at91/at91cap9.c b/arch/arm/mach-at91/at91cap9.c
index 0fc0adaebd5..73376170fb9 100644
--- a/arch/arm/mach-at91/at91cap9.c
+++ b/arch/arm/mach-at91/at91cap9.c
@@ -15,8 +15,11 @@
 #include <linux/module.h>
 #include <linux/pm.h>
 
+#include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+
+#include <mach/cpu.h>
 #include <mach/at91cap9.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
@@ -317,6 +320,12 @@ void __init at91cap9_initialize(unsigned long main_clock)
 
 	/* Register GPIO subsystem */
 	at91_gpio_init(at91cap9_gpio, 4);
+
+	/* Remember the silicon revision */
+	if (cpu_is_at91cap9_revB())
+		system_rev = 0xB;
+	else if (cpu_is_at91cap9_revC())
+		system_rev = 0xC;
 }
 
 /* --------------------------------------------------------------------
diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c
index 5ebd4273d35..9eca2209cde 100644
--- a/arch/arm/mach-at91/at91cap9_devices.c
+++ b/arch/arm/mach-at91/at91cap9_devices.c
@@ -13,6 +13,7 @@
  */
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+#include <asm/mach/irq.h>
 
 #include <linux/dma-mapping.h>
 #include <linux/platform_device.h>
@@ -21,6 +22,7 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
+#include <mach/cpu.h>
 #include <mach/gpio.h>
 #include <mach/at91cap9.h>
 #include <mach/at91cap9_matrix.h>
@@ -69,6 +71,9 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 	if (!data)
 		return;
 
+	if (cpu_is_at91cap9_revB())
+		set_irq_type(AT91CAP9_ID_UHP, IRQ_TYPE_LEVEL_HIGH);
+
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (data->vbus_pin[i])
@@ -151,8 +156,13 @@ static struct platform_device at91_usba_udc_device = {
 
 void __init at91_add_device_usba(struct usba_platform_data *data)
 {
-	at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS |
-					  AT91_MATRIX_UDPHS_BYPASS_LOCK);
+	if (cpu_is_at91cap9_revB()) {
+		set_irq_type(AT91CAP9_ID_UDPHS, IRQ_TYPE_LEVEL_HIGH);
+		at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS |
+						  AT91_MATRIX_UDPHS_BYPASS_LOCK);
+	}
+	else
+		at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS);
 
 	/*
 	 * Invalid pins are 0 on AT91, but the usba driver is shared
@@ -406,28 +416,13 @@ static struct platform_device at91cap9_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
 
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
-	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
-
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(1)
-			| AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(1));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(6)
-			| AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(6));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(8) | AT91_SMC_NRDCYCLE_(8));
-
-	if (data->bus_width_16)
-		mode = AT91_SMC_DBW_16;
-	else
-		mode = AT91_SMC_DBW_8;
-	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1));
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
 	if (data->enable_pin)
@@ -865,6 +860,9 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 	if (!data)
 		return;
 
+	if (cpu_is_at91cap9_revB())
+		set_irq_type(AT91CAP9_ID_LCDC, IRQ_TYPE_LEVEL_HIGH);
+
 	at91_set_A_periph(AT91_PIN_PC1, 0);	/* LCDHSYNC */
 	at91_set_A_periph(AT91_PIN_PC2, 0);	/* LCDDOTCK */
 	at91_set_A_periph(AT91_PIN_PC3, 0);	/* LCDDEN */
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 28594fcc88e..2e9ecad97f3 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -12,6 +12,7 @@
 
 #include <linux/module.h>
 
+#include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <mach/at91rm9200.h>
diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c
index a72e798a2a4..1ff1bda0a89 100644
--- a/arch/arm/mach-at91/at91rm9200_time.c
+++ b/arch/arm/mach-at91/at91rm9200_time.c
@@ -141,6 +141,15 @@ clkevt32k_next_event(unsigned long delta, struct clock_event_device *dev)
 	/* Use "raw" primitives so we behave correctly on RT kernels. */
 	raw_local_irq_save(flags);
 
+	/*
+	 * According to Thomas Gleixner irqs are already disabled here.  Simply
+	 * removing raw_local_irq_save above (and the matching
+	 * raw_local_irq_restore) was not accepted.  See
+	 * http://thread.gmane.org/gmane.linux.ports.arm.kernel/41174
+	 * So for now (2008-11-20) just warn once if irqs were not disabled ...
+	 */
+	WARN_ON_ONCE(!raw_irqs_disabled_flags(flags));
+
 	/* The alarm IRQ uses absolute time (now+delta), not the relative
 	 * time (delta) in our calling convention.  Like all clockevents
 	 * using such "match" hardware, we have a race to defend against.
@@ -169,7 +178,6 @@ static struct clock_event_device clkevt = {
 	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
 	.shift		= 32,
 	.rating		= 150,
-	.cpumask	= CPU_MASK_CPU0,
 	.set_next_event	= clkevt32k_next_event,
 	.set_mode	= clkevt32k_mode,
 };
@@ -197,7 +205,7 @@ void __init at91rm9200_timer_init(void)
 	clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift);
 	clkevt.max_delta_ns = clockevent_delta2ns(AT91_ST_ALMV, &clkevt);
 	clkevt.min_delta_ns = clockevent_delta2ns(2, &clkevt) + 1;
-	clkevt.cpumask = cpumask_of_cpu(0);
+	clkevt.cpumask = cpumask_of(0);
 	clockevents_register_device(&clkevt);
 
 	/* register clocksource */
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index accb69ec478..0894f1077be 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/pm.h>
 
+#include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <mach/cpu.h>
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 7774d17dde7..fdde1ea21b0 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -313,7 +313,7 @@ static struct platform_device at91sam9260_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
@@ -321,42 +321,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-	if (cpu_is_at91sam9260()) {
-		/* Timing for sam9260 */
-		/* set the bus interface characteristics */
-		at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-				| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-		at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-				| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-		at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-		if (data->bus_width_16)
-			mode = AT91_SMC_DBW_16;
-		else
-			mode = AT91_SMC_DBW_8;
-		at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-	}
-
-	if (cpu_is_at91sam9g20()) {
-		/* Timing for sam9g20 */
-		/* set the bus interface characteristics */
-		at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0)
-				| AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-
-		at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4)
-				| AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4));
-
-		at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
-
-		if (data->bus_width_16)
-			mode = AT91_SMC_DBW_16;
-		else
-			mode = AT91_SMC_DBW_8;
-		at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3));
-	}
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 7b51a59ae8b..3acd7d7e6a4 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/pm.h>
 
+#include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <mach/at91sam9261.h>
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 6b89172310c..17289756f80 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -223,7 +223,7 @@ static struct platform_device atmel_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
@@ -231,21 +231,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-			| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-	if (data->bus_width_16)
-		mode = AT91_SMC_DBW_16;
-	else
-		mode = AT91_SMC_DBW_8;
-	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index ada4b676910..942792d630d 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/pm.h>
 
+#include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <mach/at91sam9263.h>
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 8b884083f76..b753cb879d8 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -382,7 +382,7 @@ static struct platform_device at91sam9263_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
@@ -390,21 +390,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
 	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-			| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-	if (data->bus_width_16)
-		mode = AT91_SMC_DBW_16;
-	else
-		mode = AT91_SMC_DBW_8;
-	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);
diff --git a/arch/arm/mach-at91/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c
index 122fd77ed58..b63e1d5f1ba 100644
--- a/arch/arm/mach-at91/at91sam926x_time.c
+++ b/arch/arm/mach-at91/at91sam926x_time.c
@@ -91,7 +91,6 @@ static struct clock_event_device pit_clkevt = {
 	.features	= CLOCK_EVT_FEAT_PERIODIC,
 	.shift		= 32,
 	.rating		= 100,
-	.cpumask	= CPU_MASK_CPU0,
 	.set_mode	= pit_clkevt_mode,
 };
 
@@ -173,6 +172,7 @@ static void __init at91sam926x_pit_init(void)
 
 	/* Set up and register clockevents */
 	pit_clkevt.mult = div_sc(pit_rate, NSEC_PER_SEC, pit_clkevt.shift);
+	pit_clkevt.cpumask = cpumask_of(0);
 	clockevents_register_device(&pit_clkevt);
 }
 
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index 252e954b49f..211c5c14a1e 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -12,6 +12,7 @@
 #include <linux/module.h>
 #include <linux/pm.h>
 
+#include <asm/irq.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <mach/cpu.h>
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index 87deb1e1b52..145324f4ec5 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -232,17 +232,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-			| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-	at91_sys_write(AT91_SMC_MODE(3), AT91_SMC_DBW_8 | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);
diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index cdddca54b93..d3ba29c5d8c 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -39,7 +39,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -151,6 +153,32 @@ static struct atmel_nand_data __initdata cam60_nand_data = {
 	.partition_info	= nand_partitions,
 };
 
+static struct sam9_smc_config __initdata cam60_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init cam60_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &cam60_nand_smc_config);
+
+	at91_add_device_nand(&cam60_nand_data);
+}
+
 
 static void __init cam60_board_init(void)
 {
@@ -165,7 +193,7 @@ static void __init cam60_board_init(void)
 	at91_set_gpio_output(AT91_PIN_PB18, 1);
 	at91_add_device_usbh(&cam60_usbh_data);
 	/* NAND */
-	at91_add_device_nand(&cam60_nand_data);
+	cam60_add_device_nand();
 }
 
 MACHINE_START(CAM60, "KwikByte CAM60")
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c
index 201b89392dc..83a1a0fef47 100644
--- a/arch/arm/mach-at91/board-cap9adk.c
+++ b/arch/arm/mach-at91/board-cap9adk.c
@@ -36,17 +36,16 @@
 #include <mach/hardware.h>
 #include <asm/setup.h>
 #include <asm/mach-types.h>
-#include <asm/irq.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
-#include <asm/mach/irq.h>
 
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -195,6 +194,43 @@ static struct atmel_nand_data __initdata cap9adk_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata cap9adk_nand_smc_config = {
+	.ncs_read_setup		= 1,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 1,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 6,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 6,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 8,
+	.write_cycle		= 8,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 1,
+};
+
+static void __init cap9adk_add_device_nand(void)
+{
+	unsigned long csa;
+
+	csa = at91_sys_read(AT91_MATRIX_EBICSA);
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
+
+	/* setup bus-width (8 or 16) */
+	if (cap9adk_nand_data.bus_width_16)
+		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &cap9adk_nand_smc_config);
+
+	at91_add_device_nand(&cap9adk_nand_data);
+}
+
 
 /*
  * NOR flash
@@ -234,6 +270,24 @@ static struct platform_device cap9adk_nor_flash = {
 	.num_resources	= ARRAY_SIZE(nor_flash_resources),
 };
 
+static struct sam9_smc_config __initdata cap9adk_nor_smc_config = {
+	.ncs_read_setup		= 2,
+	.nrd_setup		= 4,
+	.ncs_write_setup	= 2,
+	.nwe_setup		= 4,
+
+	.ncs_read_pulse		= 10,
+	.nrd_pulse		= 8,
+	.ncs_write_pulse	= 10,
+	.nwe_pulse		= 8,
+
+	.read_cycle		= 16,
+	.write_cycle		= 16,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+	.tdf_cycles		= 1,
+};
+
 static __init void cap9adk_add_device_nor(void)
 {
 	unsigned long csa;
@@ -241,18 +295,8 @@ static __init void cap9adk_add_device_nor(void)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(0), AT91_SMC_NWESETUP_(4) | AT91_SMC_NCS_WRSETUP_(2)
-			| AT91_SMC_NRDSETUP_(4) | AT91_SMC_NCS_RDSETUP_(2));
-
-	at91_sys_write(AT91_SMC_PULSE(0), AT91_SMC_NWEPULSE_(8) | AT91_SMC_NCS_WRPULSE_(10)
-			| AT91_SMC_NRDPULSE_(8) | AT91_SMC_NCS_RDPULSE_(10));
-
-	at91_sys_write(AT91_SMC_CYCLE(0), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
-
-	at91_sys_write(AT91_SMC_MODE(0), AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-			| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE
-			| AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+	/* configure chip-select 0 (NOR) */
+	sam9_smc_configure(0, &cap9adk_nor_smc_config);
 
 	platform_device_register(&cap9adk_nor_flash);
 }
@@ -330,10 +374,8 @@ static void __init cap9adk_board_init(void)
 	/* Serial */
 	at91_add_device_serial();
 	/* USB Host */
-	set_irq_type(AT91CAP9_ID_UHP, IRQ_TYPE_LEVEL_HIGH);
 	at91_add_device_usbh(&cap9adk_usbh_data);
 	/* USB HS */
-	set_irq_type(AT91CAP9_ID_UDPHS, IRQ_TYPE_LEVEL_HIGH);
 	at91_add_device_usba(&cap9adk_usba_udc_data);
 	/* SPI */
 	at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices));
@@ -344,13 +386,12 @@ static void __init cap9adk_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&cap9adk_macb_data);
 	/* NAND */
-	at91_add_device_nand(&cap9adk_nand_data);
+	cap9adk_add_device_nand();
 	/* NOR Flash */
 	cap9adk_add_device_nor();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* LCD Controller */
-	set_irq_type(AT91CAP9_ID_LCDC, IRQ_TYPE_LEVEL_HIGH);
 	at91_add_device_lcdc(&cap9adk_lcdc_data);
 	/* AC97 */
 	at91_add_device_ac97(&cap9adk_ac97_data);
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
new file mode 100644
index 00000000000..9ba7ba2cc3b
--- /dev/null
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -0,0 +1,397 @@
+/*
+ * linux/arch/arm/mach-at91/board-neocore926.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2007 Atmel Corporation
+ *  Copyright (C) 2008 ADENEO.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init neocore926_map_io(void)
+{
+	/* Initialize processor: 20 MHz crystal */
+	at91sam9263_initialize(20000000);
+
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init neocore926_init_irq(void)
+{
+	at91sam9263_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata neocore926_usbh_data = {
+	.ports		= 2,
+	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata neocore926_udc_data = {
+	.vbus_pin	= AT91_PIN_PA25,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * ADS7846 Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+static int ads7843_pendown_state(void)
+{
+	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+	.model			= 7843,
+	.x_min			= 150,
+	.x_max			= 3830,
+	.y_min			= 190,
+	.y_max			= 3830,
+	.vref_delay_usecs	= 100,
+	.x_plate_ohms		= 450,
+	.y_plate_ohms		= 250,
+	.pressure_max		= 15000,
+	.debounce_max		= 1,
+	.debounce_rep		= 0,
+	.debounce_tol		= (~0),
+	.get_pendown_state	= ads7843_pendown_state,
+};
+
+static void __init neocore926_add_device_ts(void)
+{
+	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
+	at91_set_gpio_input(AT91_PIN_PC13, 1);	/* Touchscreen BUSY signal */
+}
+#else
+static void __init neocore926_add_device_ts(void) {}
+#endif
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info neocore926_spi_devices[] = {
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+	{
+		.modalias	= "ads7846",
+		.chip_select	= 1,
+		.max_speed_hz	= 125000 * 16,
+		.bus_num	= 0,
+		.platform_data	= &ads_info,
+		.irq		= AT91SAM9263_ID_IRQ1,
+	},
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata neocore926_mmc_data = {
+	.wire4		= 1,
+	.det_pin	= AT91_PIN_PE18,
+	.wp_pin		= AT91_PIN_PE19,
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata neocore926_macb_data = {
+	.phy_irq_pin	= AT91_PIN_PE31,
+	.is_rmii	= 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata neocore926_nand_partition[] = {
+	{
+		.name	= "Linux Kernel",	/* "Partition 1", */
+		.offset	= 0,
+		.size	= SZ_8M,
+	},
+	{
+		.name	= "Filesystem",		/* "Partition 2", */
+		.offset	= MTDPART_OFS_NXTBLK,
+		.size	= SZ_32M,
+	},
+	{
+		.name	= "Free",		/* "Partition 3", */
+		.offset	= MTDPART_OFS_NXTBLK,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(neocore926_nand_partition);
+	return neocore926_nand_partition;
+}
+
+static struct atmel_nand_data __initdata neocore926_nand_data = {
+	.ale			= 21,
+	.cle			= 22,
+	.rdy_pin		= AT91_PIN_PB19,
+	.rdy_pin_active_low	= 1,
+	.enable_pin		= AT91_PIN_PD15,
+	.partition_info		= nand_partitions,
+};
+
+static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 6,
+	.write_cycle		= 6,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init neocore926_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &neocore926_nand_smc_config);
+
+	at91_add_device_nand(&neocore926_nand_data);
+}
+
+
+/*
+ * LCD Controller
+ */
+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+static struct fb_videomode at91_tft_vga_modes[] = {
+	{
+		.name		= "TX09D50VM1CCA @ 60",
+		.refresh	= 60,
+		.xres		= 240,		.yres		= 320,
+		.pixclock	= KHZ2PICOS(5000),
+
+		.left_margin	= 1,		.right_margin	= 33,
+		.upper_margin	= 1,		.lower_margin	= 0,
+		.hsync_len	= 5,		.vsync_len	= 1,
+
+		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+};
+
+static struct fb_monspecs at91fb_default_monspecs = {
+	.manufacturer	= "HIT",
+	.monitor	= "TX09D70VM1CCA",
+
+	.modedb		= at91_tft_vga_modes,
+	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
+	.hfmin		= 15000,
+	.hfmax		= 64000,
+	.vfmin		= 50,
+	.vfmax		= 150,
+};
+
+#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+					| ATMEL_LCDC_DISTYPE_TFT \
+					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
+
+static void at91_lcdc_power_control(int on)
+{
+	at91_set_gpio_value(AT91_PIN_PA30, on);
+}
+
+/* Driver datas */
+static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
+	.lcdcon_is_backlight		= true,
+	.default_bpp			= 16,
+	.default_dmacon			= ATMEL_LCDC_DMAEN,
+	.default_lcdcon2		= AT91SAM9263_DEFAULT_LCDCON2,
+	.default_monspecs		= &at91fb_default_monspecs,
+	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
+	.guard_time			= 1,
+	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB555,
+};
+
+#else
+static struct atmel_lcdfb_info __initdata neocore926_lcdc_data;
+#endif
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button neocore926_buttons[] = {
+	{	/* BP1, "leftclic" */
+		.code		= BTN_LEFT,
+		.gpio		= AT91_PIN_PC5,
+		.active_low	= 1,
+		.desc		= "left_click",
+		.wakeup		= 1,
+	},
+	{	/* BP2, "rightclic" */
+		.code		= BTN_RIGHT,
+		.gpio		= AT91_PIN_PC4,
+		.active_low	= 1,
+		.desc		= "right_click",
+		.wakeup		= 1,
+	},
+};
+
+static struct gpio_keys_platform_data neocore926_button_data = {
+	.buttons	= neocore926_buttons,
+	.nbuttons	= ARRAY_SIZE(neocore926_buttons),
+};
+
+static struct platform_device neocore926_button_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &neocore926_button_data,
+	}
+};
+
+static void __init neocore926_add_device_buttons(void)
+{
+	at91_set_GPIO_periph(AT91_PIN_PC5, 0);	/* left button */
+	at91_set_deglitch(AT91_PIN_PC5, 1);
+	at91_set_GPIO_periph(AT91_PIN_PC4, 0);	/* right button */
+	at91_set_deglitch(AT91_PIN_PC4, 1);
+
+	platform_device_register(&neocore926_button_device);
+}
+#else
+static void __init neocore926_add_device_buttons(void) {}
+#endif
+
+
+/*
+ * AC97
+ */
+static struct atmel_ac97_data neocore926_ac97_data = {
+	.reset_pin	= AT91_PIN_PA13,
+};
+
+
+static void __init neocore926_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+
+	/* USB Host */
+	at91_add_device_usbh(&neocore926_usbh_data);
+
+	/* USB Device */
+	at91_add_device_udc(&neocore926_udc_data);
+
+	/* SPI */
+	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
+	at91_add_device_spi(neocore926_spi_devices, ARRAY_SIZE(neocore926_spi_devices));
+
+	/* Touchscreen */
+	neocore926_add_device_ts();
+
+	/* MMC */
+	at91_add_device_mmc(1, &neocore926_mmc_data);
+
+	/* Ethernet */
+	at91_add_device_eth(&neocore926_macb_data);
+
+	/* NAND */
+	neocore926_add_device_nand();
+
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+
+	/* LCD Controller */
+	at91_add_device_lcdc(&neocore926_lcdc_data);
+
+	/* Push Buttons */
+	neocore926_add_device_buttons();
+
+	/* AC97 */
+	at91_add_device_ac97(&neocore926_ac97_data);
+}
+
+MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926")
+	/* Maintainer: ADENEO */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= neocore926_map_io,
+	.init_irq	= neocore926_init_irq,
+	.init_machine	= neocore926_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index cfb4571a2e2..4cff9a7e61d 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -41,8 +41,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -147,13 +149,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 /*
  * MCI (SD/MMC)
  */
@@ -227,7 +250,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Ethernet */
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index 99bb4cc23a0..b4834697753 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -38,7 +38,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -148,13 +150,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -178,7 +201,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index b49eb6e4918..93a0f8b100e 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -42,7 +42,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -195,6 +198,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -303,7 +338,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 4977409d4fc..d5266da5531 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -47,7 +47,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -76,7 +78,7 @@ static void __init ek_init_irq(void)
  * DM9000 ethernet device
  */
 #if defined(CONFIG_DM9000)
-static struct resource at91sam9261_dm9000_resource[] = {
+static struct resource dm9000_resource[] = {
 	[0] = {
 		.start	= AT91_CHIPSELECT_2,
 		.end	= AT91_CHIPSELECT_2 + 3,
@@ -98,27 +100,42 @@ static struct dm9000_plat_data dm9000_platdata = {
 	.flags		= DM9000_PLATF_16BITONLY,
 };
 
-static struct platform_device at91sam9261_dm9000_device = {
+static struct platform_device dm9000_device = {
 	.name		= "dm9000",
 	.id		= 0,
-	.num_resources	= ARRAY_SIZE(at91sam9261_dm9000_resource),
-	.resource	= at91sam9261_dm9000_resource,
+	.num_resources	= ARRAY_SIZE(dm9000_resource),
+	.resource	= dm9000_resource,
 	.dev		= {
 		.platform_data	= &dm9000_platdata,
 	}
 };
 
+/*
+ * SMC timings for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
+ */
+static struct sam9_smc_config __initdata dm9000_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 8,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 8,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 16,
+	.write_cycle		= 16,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+	.tdf_cycles		= 1,
+};
+
 static void __init ek_add_device_dm9000(void)
 {
-	/*
-	 * Configure Chip-Select 2 on SMC for the DM9000.
-	 * Note: These timings were calculated for MASTER_CLOCK = 100000000
-	 *  according to the DM9000 timings.
-	 */
-	at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-	at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
-	at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
-	at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+	/* Configure chip-select 2 (DM9000) */
+	sam9_smc_configure(2, &dm9000_smc_config);
 
 	/* Configure Reset signal as output */
 	at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -126,7 +143,7 @@ static void __init ek_add_device_dm9000(void)
 	/* Configure Interrupt pin as input, no pull-up */
 	at91_set_gpio_input(AT91_PIN_PC11, 0);
 
-	platform_device_register(&at91sam9261_dm9000_device);
+	platform_device_register(&dm9000_device);
 }
 #else
 static void __init ek_add_device_dm9000(void) {}
@@ -197,6 +214,39 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
 /*
  * ADS7846 Touchscreen
  */
@@ -525,7 +575,7 @@ static void __init ek_board_init(void)
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* DM9000 ethernet */
 	ek_add_device_dm9000();
 
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 8354015c6a2..57d52528f22 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -46,7 +46,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -203,6 +205,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * I2C devices
@@ -385,7 +419,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
 	/* LCD Controller */
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index b588ead14d6..81439fe6fb3 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -37,7 +37,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -156,6 +158,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 7,
+	.write_cycle		= 7,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 3,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -195,7 +229,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index 27085186430..35e12a49d1a 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -30,7 +30,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -103,9 +105,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.partition_info	= nand_partitions,
-	.bus_width_16	= 0,
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * SPI devices
@@ -188,7 +215,7 @@ static void __init ek_board_init(void)
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* MMC */
diff --git a/arch/arm/mach-at91/board-usb-a9260.c b/arch/arm/mach-at91/board-usb-a9260.c
index 7c350357333..d13304c0bc4 100644
--- a/arch/arm/mach-at91/board-usb-a9260.c
+++ b/arch/arm/mach-at91/board-usb-a9260.c
@@ -41,8 +41,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -121,13 +123,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 /*
  * GPIO Buttons
  */
@@ -189,7 +212,7 @@ static void __init ek_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&ek_udc_data);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Ethernet */
diff --git a/arch/arm/mach-at91/board-usb-a9263.c b/arch/arm/mach-at91/board-usb-a9263.c
index 391b566c457..d96405b7d57 100644
--- a/arch/arm/mach-at91/board-usb-a9263.c
+++ b/arch/arm/mach-at91/board-usb-a9263.c
@@ -40,8 +40,10 @@
 #include <mach/hardware.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -134,13 +136,35 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
 /*
  * GPIO Buttons
  */
@@ -206,7 +230,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Push Buttons */
diff --git a/arch/arm/mach-at91/include/mach/at91_pmc.h b/arch/arm/mach-at91/include/mach/at91_pmc.h
index 2e3f2894b70..9561e33b8a9 100644
--- a/arch/arm/mach-at91/include/mach/at91_pmc.h
+++ b/arch/arm/mach-at91/include/mach/at91_pmc.h
@@ -23,6 +23,7 @@
 #define		AT91_PMC_PCK		(1 <<  0)		/* Processor Clock */
 #define		AT91RM9200_PMC_UDP	(1 <<  1)		/* USB Devcice Port Clock [AT91RM9200 only] */
 #define		AT91RM9200_PMC_MCKUDP	(1 <<  2)		/* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */
+#define		AT91CAP9_PMC_DDR	(1 <<  2)		/* DDR Clock [AT91CAP9 revC only] */
 #define		AT91RM9200_PMC_UHP	(1 <<  4)		/* USB Host Port Clock [AT91RM9200 only] */
 #define		AT91SAM926x_PMC_UHP	(1 <<  6)		/* USB Host Port Clock [AT91SAM926x only] */
 #define		AT91CAP9_PMC_UHP	(1 <<  6)		/* USB Host Port Clock [AT91CAP9 only] */
@@ -102,10 +103,16 @@
 #define		AT91_PMC_LOCKB		(1 <<  2)		/* PLLB Lock */
 #define		AT91_PMC_MCKRDY		(1 <<  3)		/* Master Clock */
 #define		AT91_PMC_LOCKU		(1 <<  6)		/* UPLL Lock [AT91CAP9 only] */
+#define		AT91_PMC_OSCSEL		(1 <<  7)		/* Slow Clock Oscillator [AT91CAP9 revC only] */
 #define		AT91_PMC_PCK0RDY	(1 <<  8)		/* Programmable Clock 0 */
 #define		AT91_PMC_PCK1RDY	(1 <<  9)		/* Programmable Clock 1 */
 #define		AT91_PMC_PCK2RDY	(1 << 10)		/* Programmable Clock 2 */
 #define		AT91_PMC_PCK3RDY	(1 << 11)		/* Programmable Clock 3 */
 #define	AT91_PMC_IMR		(AT91_PMC + 0x6c)	/* Interrupt Mask Register */
 
+#define AT91_PMC_PROT		(AT91_PMC + 0xe4)	/* Protect Register [AT91CAP9 revC only] */
+#define		AT91_PMC_PROTKEY	0x504d4301	/* Activation Code */
+
+#define AT91_PMC_VER		(AT91_PMC + 0xfc)	/* PMC Module Version [AT91CAP9 only] */
+
 #endif
diff --git a/arch/arm/mach-at91/include/mach/at91cap9.h b/arch/arm/mach-at91/include/mach/at91cap9.h
index 4a4b64135a9..d8c1ededaa7 100644
--- a/arch/arm/mach-at91/include/mach/at91cap9.h
+++ b/arch/arm/mach-at91/include/mach/at91cap9.h
@@ -101,7 +101,9 @@
 #define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
 #define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
 #define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
-#define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
+#define AT91_GPBR	(cpu_is_at91cap9_revB() ?	\
+			(0xfffffd50 - AT91_BASE_SYS) :	\
+			(0xfffffd60 - AT91_BASE_SYS))
 
 #define AT91_USART0	AT91CAP9_BASE_US0
 #define AT91_USART1	AT91CAP9_BASE_US1
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index dbfd9f73f80..c554c3e4d55 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -49,6 +49,17 @@ static inline unsigned long at91_arch_identify(void)
 	return (at91_sys_read(AT91_DBGU_CIDR) & AT91_CIDR_ARCH);
 }
 
+#ifdef CONFIG_ARCH_AT91CAP9
+#include <mach/at91_pmc.h>
+
+#define ARCH_REVISION_CAP9_B	0x399
+#define ARCH_REVISION_CAP9_C	0x601
+
+static inline unsigned long at91cap9_rev_identify(void)
+{
+	return (at91_sys_read(AT91_PMC_VER));
+}
+#endif
 
 #ifdef CONFIG_ARCH_AT91RM9200
 #define cpu_is_at91rm9200()	(at91_cpu_identify() == ARCH_ID_AT91RM9200)
@@ -90,8 +101,12 @@ static inline unsigned long at91_arch_identify(void)
 
 #ifdef CONFIG_ARCH_AT91CAP9
 #define cpu_is_at91cap9()	(at91_cpu_identify() == ARCH_ID_AT91CAP9)
+#define cpu_is_at91cap9_revB()	(at91cap9_rev_identify() == ARCH_REVISION_CAP9_B)
+#define cpu_is_at91cap9_revC()	(at91cap9_rev_identify() == ARCH_REVISION_CAP9_C)
 #else
 #define cpu_is_at91cap9()	(0)
+#define cpu_is_at91cap9_revB()	(0)
+#define cpu_is_at91cap9_revC()	(0)
 #endif
 
 /*
diff --git a/arch/arm/mach-at91/include/mach/dma.h b/arch/arm/mach-at91/include/mach/dma.h
deleted file mode 100644
index e4f90c17761..00000000000
--- a/arch/arm/mach-at91/include/mach/dma.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/dma.h
- *
- *  Copyright (C) 2003 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
diff --git a/arch/arm/mach-at91/include/mach/io.h b/arch/arm/mach-at91/include/mach/io.h
index 1611bd03f52..0b0cccc46e6 100644
--- a/arch/arm/mach-at91/include/mach/io.h
+++ b/arch/arm/mach-at91/include/mach/io.h
@@ -23,8 +23,8 @@
 
 #define IO_SPACE_LIMIT		0xFFFFFFFF
 
-#define __io(a)			((void __iomem *)(a))
-#define __mem_pci(a)		(a)
+#define __io(a)		__typesafe_io(a)
+#define __mem_pci(a)	(a)
 
 
 #ifndef __ASSEMBLY__
diff --git a/arch/arm/mach-at91/include/mach/memory.h b/arch/arm/mach-at91/include/mach/memory.h
index 9dd1b8c79b0..14f4ef4b6a9 100644
--- a/arch/arm/mach-at91/include/mach/memory.h
+++ b/arch/arm/mach-at91/include/mach/memory.h
@@ -25,15 +25,4 @@
 
 #define PHYS_OFFSET	(AT91_SDRAM_BASE)
 
-
-/*
- * Virtual view <-> DMA view memory address translations
- * virt_to_bus: Used to translate the virtual address to an
- *              address suitable to be passed to set_dma_addr
- * bus_to_virt: Used to convert an address for DMA operations
- *              to an address that the kernel can use.
- */
-#define __virt_to_bus(x) __virt_to_phys(x)
-#define __bus_to_virt(x) __phys_to_virt(x)
-
 #endif
diff --git a/arch/arm/mach-at91/sam9_smc.c b/arch/arm/mach-at91/sam9_smc.c
new file mode 100644
index 00000000000..5eab6aa621d
--- /dev/null
+++ b/arch/arm/mach-at91/sam9_smc.c
@@ -0,0 +1,47 @@
+/*
+ * linux/arch/arm/mach-at91/sam9_smc.c
+ *
+ * Copyright (C) 2008 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/io.h>
+
+#include <mach/at91sam9_smc.h>
+
+#include "sam9_smc.h"
+
+void __init sam9_smc_configure(int cs, struct sam9_smc_config* config)
+{
+	/* Setup register */
+	at91_sys_write(AT91_SMC_SETUP(cs),
+		  AT91_SMC_NWESETUP_(config->nwe_setup)
+		| AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
+		| AT91_SMC_NRDSETUP_(config->nrd_setup)
+		| AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup)
+	);
+
+	/* Pulse register */
+	at91_sys_write(AT91_SMC_PULSE(cs),
+		  AT91_SMC_NWEPULSE_(config->nwe_pulse)
+		| AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
+                | AT91_SMC_NRDPULSE_(config->nrd_pulse)
+		| AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse)
+	);
+
+	/* Cycle register */
+	at91_sys_write(AT91_SMC_CYCLE(cs),
+		  AT91_SMC_NWECYCLE_(config->write_cycle)
+		| AT91_SMC_NRDCYCLE_(config->read_cycle)
+	);
+
+	/* Mode register */
+	at91_sys_write(AT91_SMC_MODE(cs),
+		  config->mode
+		| AT91_SMC_TDF_(config->tdf_cycles)
+	);
+}
diff --git a/arch/arm/mach-at91/sam9_smc.h b/arch/arm/mach-at91/sam9_smc.h
new file mode 100644
index 00000000000..bf72cfb3455
--- /dev/null
+++ b/arch/arm/mach-at91/sam9_smc.h
@@ -0,0 +1,33 @@
+/*
+ * linux/arch/arm/mach-at91/sam9_smc.
+ *
+ * Copyright (C) 2008 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+struct sam9_smc_config {
+	/* Setup register */
+	u8 ncs_read_setup;
+	u8 nrd_setup;
+	u8 ncs_write_setup;
+	u8 nwe_setup;
+
+	/* Pulse register */
+	u8 ncs_read_pulse;
+	u8 nrd_pulse;
+	u8 ncs_write_pulse;
+	u8 nwe_pulse;
+
+	/* Cycle register */
+	u16 read_cycle;
+	u16 write_cycle;
+
+	/* Mode register */
+	u32 mode;
+	u8 tdf_cycles:4;
+};
+
+extern void __init sam9_smc_configure(int cs, struct sam9_smc_config* config);