Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

Conflicts:
	arch/sh/kernel/vmlinux.lds.S

1 files changed, 110 insertions, 65 deletions

diff --git a/drivers/net/igb/e1000_mac.c b/drivers/net/igb/e1000_mac.c
index 472f3f12484..a0231cd079f 100644
--- a/drivers/net/igb/e1000_mac.c
+++ b/drivers/net/igb/e1000_mac.c
@@ -37,20 +37,6 @@
 static s32 igb_set_default_fc(struct e1000_hw *hw);
 static s32 igb_set_fc_watermarks(struct e1000_hw *hw);
 
-static s32 igb_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value)
-{
-	struct igb_adapter *adapter = hw->back;
-	u16 cap_offset;
-
-	cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
-	if (!cap_offset)
-		return -E1000_ERR_CONFIG;
-
-	pci_read_config_word(adapter->pdev, cap_offset + reg, value);
-
-	return 0;
-}
-
 /**
  *  igb_get_bus_info_pcie - Get PCIe bus information
  *  @hw: pointer to the HW structure
@@ -118,6 +104,31 @@ static void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
 }
 
 /**
+ *  igb_init_rx_addrs - Initialize receive address's
+ *  @hw: pointer to the HW structure
+ *  @rar_count: receive address registers
+ *
+ *  Setups the receive address registers by setting the base receive address
+ *  register to the devices MAC address and clearing all the other receive
+ *  address registers to 0.
+ **/
+void igb_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
+{
+	u32 i;
+	u8 mac_addr[ETH_ALEN] = {0};
+
+	/* Setup the receive address */
+	hw_dbg("Programming MAC Address into RAR[0]\n");
+
+	hw->mac.ops.rar_set(hw, hw->mac.addr, 0);
+
+	/* Zero out the other (rar_entry_count - 1) receive addresses */
+	hw_dbg("Clearing RAR[1-%u]\n", rar_count-1);
+	for (i = 1; i < rar_count; i++)
+		hw->mac.ops.rar_set(hw, mac_addr, i);
+}
+
+/**
  *  igb_vfta_set - enable or disable vlan in VLAN filter table
  *  @hw: pointer to the HW structure
  *  @vid: VLAN id to add or remove
@@ -275,6 +286,41 @@ void igb_mta_set(struct e1000_hw *hw, u32 hash_value)
 }
 
 /**
+ *  igb_update_mc_addr_list - Update Multicast addresses
+ *  @hw: pointer to the HW structure
+ *  @mc_addr_list: array of multicast addresses to program
+ *  @mc_addr_count: number of multicast addresses to program
+ *
+ *  Updates entire Multicast Table Array.
+ *  The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+void igb_update_mc_addr_list(struct e1000_hw *hw,
+                             u8 *mc_addr_list, u32 mc_addr_count)
+{
+	u32 hash_value, hash_bit, hash_reg;
+	int i;
+
+	/* clear mta_shadow */
+	memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
+
+	/* update mta_shadow from mc_addr_list */
+	for (i = 0; (u32) i < mc_addr_count; i++) {
+		hash_value = igb_hash_mc_addr(hw, mc_addr_list);
+
+		hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+		hash_bit = hash_value & 0x1F;
+
+		hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
+		mc_addr_list += (ETH_ALEN);
+	}
+
+	/* replace the entire MTA table */
+	for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
+		array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
+	wrfl();
+}
+
+/**
  *  igb_hash_mc_addr - Generate a multicast hash value
  *  @hw: pointer to the HW structure
  *  @mc_addr: pointer to a multicast address
@@ -490,18 +536,24 @@ s32 igb_setup_link(struct e1000_hw *hw)
 	if (igb_check_reset_block(hw))
 		goto out;
 
-	ret_val = igb_set_default_fc(hw);
-	if (ret_val)
-		goto out;
+	/*
+	 * If requested flow control is set to default, set flow control
+	 * based on the EEPROM flow control settings.
+	 */
+	if (hw->fc.requested_mode == e1000_fc_default) {
+		ret_val = igb_set_default_fc(hw);
+		if (ret_val)
+			goto out;
+	}
 
 	/*
 	 * We want to save off the original Flow Control configuration just
 	 * in case we get disconnected and then reconnected into a different
 	 * hub or switch with different Flow Control capabilities.
 	 */
-	hw->fc.original_type = hw->fc.type;
+	hw->fc.current_mode = hw->fc.requested_mode;
 
-	hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.type);
+	hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode);
 
 	/* Call the necessary media_type subroutine to configure the link. */
 	ret_val = hw->mac.ops.setup_physical_interface(hw);
@@ -568,7 +620,7 @@ static s32 igb_set_fc_watermarks(struct e1000_hw *hw)
 	 * ability to transmit pause frames is not enabled, then these
 	 * registers will be set to 0.
 	 */
-	if (hw->fc.type & e1000_fc_tx_pause) {
+	if (hw->fc.current_mode & e1000_fc_tx_pause) {
 		/*
 		 * We need to set up the Receive Threshold high and low water
 		 * marks as well as (optionally) enabling the transmission of
@@ -615,12 +667,12 @@ static s32 igb_set_default_fc(struct e1000_hw *hw)
 	}
 
 	if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
-		hw->fc.type = e1000_fc_none;
+		hw->fc.requested_mode = e1000_fc_none;
 	else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
 		 NVM_WORD0F_ASM_DIR)
-		hw->fc.type = e1000_fc_tx_pause;
+		hw->fc.requested_mode = e1000_fc_tx_pause;
 	else
-		hw->fc.type = e1000_fc_full;
+		hw->fc.requested_mode = e1000_fc_full;
 
 out:
 	return ret_val;
@@ -650,7 +702,7 @@ s32 igb_force_mac_fc(struct e1000_hw *hw)
 	 * receive flow control.
 	 *
 	 * The "Case" statement below enables/disable flow control
-	 * according to the "hw->fc.type" parameter.
+	 * according to the "hw->fc.current_mode" parameter.
 	 *
 	 * The possible values of the "fc" parameter are:
 	 *      0:  Flow control is completely disabled
@@ -661,9 +713,9 @@ s32 igb_force_mac_fc(struct e1000_hw *hw)
 	 *      3:  Both Rx and TX flow control (symmetric) is enabled.
 	 *  other:  No other values should be possible at this point.
 	 */
-	hw_dbg("hw->fc.type = %u\n", hw->fc.type);
+	hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
 
-	switch (hw->fc.type) {
+	switch (hw->fc.current_mode) {
 	case e1000_fc_none:
 		ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
 		break;
@@ -713,8 +765,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
 	 * configuration of the MAC to match the "fc" parameter.
 	 */
 	if (mac->autoneg_failed) {
-		if (hw->phy.media_type == e1000_media_type_fiber ||
-		    hw->phy.media_type == e1000_media_type_internal_serdes)
+		if (hw->phy.media_type == e1000_media_type_internal_serdes)
 			ret_val = igb_force_mac_fc(hw);
 	} else {
 		if (hw->phy.media_type == e1000_media_type_copper)
@@ -812,11 +863,11 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
 			 * ONLY. Hence, we must now check to see if we need to
 			 * turn OFF  the TRANSMISSION of PAUSE frames.
 			 */
-			if (hw->fc.original_type == e1000_fc_full) {
-				hw->fc.type = e1000_fc_full;
+			if (hw->fc.requested_mode == e1000_fc_full) {
+				hw->fc.current_mode = e1000_fc_full;
 				hw_dbg("Flow Control = FULL.\r\n");
 			} else {
-				hw->fc.type = e1000_fc_rx_pause;
+				hw->fc.current_mode = e1000_fc_rx_pause;
 				hw_dbg("Flow Control = "
 				       "RX PAUSE frames only.\r\n");
 			}
@@ -833,7 +884,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
 			  (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
 			  (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
 			  (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
-			hw->fc.type = e1000_fc_tx_pause;
+			hw->fc.current_mode = e1000_fc_tx_pause;
 			hw_dbg("Flow Control = TX PAUSE frames only.\r\n");
 		}
 		/*
@@ -848,7 +899,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
 			 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
 			 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
 			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
-			hw->fc.type = e1000_fc_rx_pause;
+			hw->fc.current_mode = e1000_fc_rx_pause;
 			hw_dbg("Flow Control = RX PAUSE frames only.\r\n");
 		}
 		/*
@@ -872,13 +923,13 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
 		 * be asked to delay transmission of packets than asking
 		 * our link partner to pause transmission of frames.
 		 */
-		else if ((hw->fc.original_type == e1000_fc_none ||
-			  hw->fc.original_type == e1000_fc_tx_pause) ||
+		else if ((hw->fc.requested_mode == e1000_fc_none ||
+			  hw->fc.requested_mode == e1000_fc_tx_pause) ||
 			 hw->fc.strict_ieee) {
-			hw->fc.type = e1000_fc_none;
+			hw->fc.current_mode = e1000_fc_none;
 			hw_dbg("Flow Control = NONE.\r\n");
 		} else {
-			hw->fc.type = e1000_fc_rx_pause;
+			hw->fc.current_mode = e1000_fc_rx_pause;
 			hw_dbg("Flow Control = RX PAUSE frames only.\r\n");
 		}
 
@@ -894,7 +945,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
 		}
 
 		if (duplex == HALF_DUPLEX)
-			hw->fc.type = e1000_fc_none;
+			hw->fc.current_mode = e1000_fc_none;
 
 		/*
 		 * Now we call a subroutine to actually force the MAC
@@ -1065,9 +1116,17 @@ static s32 igb_valid_led_default(struct e1000_hw *hw, u16 *data)
 		goto out;
 	}
 
-	if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF)
-		*data = ID_LED_DEFAULT;
-
+	if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) {
+		switch(hw->phy.media_type) {
+		case e1000_media_type_internal_serdes:
+			*data = ID_LED_DEFAULT_82575_SERDES;
+			break;
+		case e1000_media_type_copper:
+		default:
+			*data = ID_LED_DEFAULT;
+			break;
+		}
+	}
 out:
 	return ret_val;
 }
@@ -1161,22 +1220,16 @@ s32 igb_blink_led(struct e1000_hw *hw)
 	u32 ledctl_blink = 0;
 	u32 i;
 
-	if (hw->phy.media_type == e1000_media_type_fiber) {
-		/* always blink LED0 for PCI-E fiber */
-		ledctl_blink = E1000_LEDCTL_LED0_BLINK |
-		     (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
-	} else {
-		/*
-		 * set the blink bit for each LED that's "on" (0x0E)
-		 * in ledctl_mode2
-		 */
-		ledctl_blink = hw->mac.ledctl_mode2;
-		for (i = 0; i < 4; i++)
-			if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
-			    E1000_LEDCTL_MODE_LED_ON)
-				ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
-						 (i * 8));
-	}
+	/*
+	 * set the blink bit for each LED that's "on" (0x0E)
+	 * in ledctl_mode2
+	 */
+	ledctl_blink = hw->mac.ledctl_mode2;
+	for (i = 0; i < 4; i++)
+		if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+		    E1000_LEDCTL_MODE_LED_ON)
+			ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
+					 (i * 8));
 
 	wr32(E1000_LEDCTL, ledctl_blink);
 
@@ -1191,15 +1244,7 @@ s32 igb_blink_led(struct e1000_hw *hw)
  **/
 s32 igb_led_off(struct e1000_hw *hw)
 {
-	u32 ctrl;
-
 	switch (hw->phy.media_type) {
-	case e1000_media_type_fiber:
-		ctrl = rd32(E1000_CTRL);
-		ctrl |= E1000_CTRL_SWDPIN0;
-		ctrl |= E1000_CTRL_SWDPIO0;
-		wr32(E1000_CTRL, ctrl);
-		break;
 	case e1000_media_type_copper:
 		wr32(E1000_LEDCTL, hw->mac.ledctl_mode1);
 		break;