aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/skge.h
diff options
context:
space:
mode:
authorStephen Hemminger <shemminger@osdl.org>2005-06-27 11:33:08 -0700
committerJeff Garzik <jgarzik@pobox.com>2005-06-27 18:05:06 -0400
commitb18f2091bc9f93548ea63752278fceaeacedab20 (patch)
tree6154380f95d261126525fc95eb149ddc8478eeea /drivers/net/skge.h
parent4707953454677f985289b4e4bcbea41f0cc651c2 (diff)
[PATCH] skge: remove unused declarations
Get rid of definitions for chip versions and PHY chips that this driver does not support. Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Diffstat (limited to 'drivers/net/skge.h')
-rw-r--r--drivers/net/skge.h402
1 files changed, 22 insertions, 380 deletions
diff --git a/drivers/net/skge.h b/drivers/net/skge.h
index e57a535c5c4..6f3a4b56a67 100644
--- a/drivers/net/skge.h
+++ b/drivers/net/skge.h
@@ -7,31 +7,6 @@
/* PCI config registers */
#define PCI_DEV_REG1 0x40
#define PCI_DEV_REG2 0x44
-#ifndef PCI_VPD
-#define PCI_VPD 0x50
-#endif
-
-/* PCI_OUR_REG_2 32 bit Our Register 2 */
-enum {
- PCI_VPD_WR_THR = 0xff<<24, /* Bit 31..24: VPD Write Threshold */
- PCI_DEV_SEL = 0x7f<<17, /* Bit 23..17: EEPROM Device Select */
- PCI_VPD_ROM_SZ = 7 <<14, /* Bit 16..14: VPD ROM Size */
- /* Bit 13..12: reserved */
- PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */
- PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */
- PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
-};
-
-/* PCI_VPD_ADR_REG 16 bit VPD Address Register */
-enum {
- PCI_VPD_FLAG = 1<<15, /* starts VPD rd/wr cycle */
- PCI_VPD_ADR_MSK =0x7fffL, /* Bit 14.. 0: VPD Address Mask */
- VPD_RES_ID = 0x82,
- VPD_RES_READ = 0x90,
- VPD_RES_WRITE = 0x81,
- VPD_RES_END = 0x78,
-};
-
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
@@ -39,7 +14,6 @@ enum {
PCI_STATUS_REC_TARGET_ABORT | \
PCI_STATUS_PARITY)
-
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
@@ -288,14 +262,6 @@ enum {
CHIP_REV_YU_LITE_A3 = 7, /* Chip Rev. for YUKON-Lite A3 */
};
-/* B2_LD_TEST 8 bit EPROM loader test register */
-enum {
- LD_T_ON = 1<<3, /* Loader Test mode on */
- LD_T_OFF = 1<<2, /* Loader Test mode off */
- LD_T_STEP = 1<<1, /* Decrement FPROM addr. Counter */
- LD_START = 1<<0, /* Start loading FPROM */
-};
-
/* B2_TI_CTRL 8 bit Timer control */
/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
enum {
@@ -313,16 +279,6 @@ enum {
TIM_T_STEP = 1<<0, /* Test step */
};
-/* B28_DPT_INI 32 bit Descriptor Poll Timer Init Val */
-/* B28_DPT_VAL 32 bit Descriptor Poll Timer Curr Val */
-/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */
-enum {
- DPT_MSK = 0x00ffffffL, /* Bit 23.. 0: Desc Poll Timer Bits */
-
- DPT_START = 1<<1, /* Start Descriptor Poll Timer */
- DPT_STOP = 1<<0, /* Stop Descriptor Poll Timer */
-};
-
/* B2_GP_IO 32 bit General Purpose I/O Register */
enum {
GP_DIR_9 = 1<<25, /* IO_9 direct, 0=In/1=Out */
@@ -348,30 +304,6 @@ enum {
GP_IO_0 = 1<<0, /* IO_0 pin */
};
-/* Rx/Tx Path related Arbiter Test Registers */
-/* B3_MA_TO_TEST 16 bit MAC Arbiter Timeout Test Reg */
-/* B3_MA_RC_TEST 16 bit MAC Arbiter Recovery Test Reg */
-/* B3_PA_TEST 16 bit Packet Arbiter Test Register */
-/* Bit 15, 11, 7, and 3 are reserved in B3_PA_TEST */
-enum {
- TX2_T_EV = 1<<15,/* TX2 Timeout/Recv Event occured */
- TX2_T_ON = 1<<14,/* TX2 Timeout/Recv Timer Test On */
- TX2_T_OFF = 1<<13,/* TX2 Timeout/Recv Timer Tst Off */
- TX2_T_STEP = 1<<12,/* TX2 Timeout/Recv Timer Step */
- TX1_T_EV = 1<<11,/* TX1 Timeout/Recv Event occured */
- TX1_T_ON = 1<<10,/* TX1 Timeout/Recv Timer Test On */
- TX1_T_OFF = 1<<9, /* TX1 Timeout/Recv Timer Tst Off */
- TX1_T_STEP = 1<<8, /* TX1 Timeout/Recv Timer Step */
- RX2_T_EV = 1<<7, /* RX2 Timeout/Recv Event occured */
- RX2_T_ON = 1<<6, /* RX2 Timeout/Recv Timer Test On */
- RX2_T_OFF = 1<<5, /* RX2 Timeout/Recv Timer Tst Off */
- RX2_T_STEP = 1<<4, /* RX2 Timeout/Recv Timer Step */
- RX1_T_EV = 1<<3, /* RX1 Timeout/Recv Event occured */
- RX1_T_ON = 1<<2, /* RX1 Timeout/Recv Timer Test On */
- RX1_T_OFF = 1<<1, /* RX1 Timeout/Recv Timer Tst Off */
- RX1_T_STEP = 1<<0, /* RX1 Timeout/Recv Timer Step */
-};
-
/* Descriptor Bit Definition */
/* TxCtrl Transmit Buffer Control Field */
/* RxCtrl Receive Buffer Control Field */
@@ -428,14 +360,6 @@ enum {
RI_RST_SET = 1<<0, /* Set RAM Interface Reset */
};
-/* B3_RI_TEST 8 bit RAM Iface Test Register */
-enum {
- RI_T_EV = 1<<3, /* Timeout Event occured */
- RI_T_ON = 1<<2, /* Timeout Timer Test On */
- RI_T_OFF = 1<<1, /* Timeout Timer Test Off */
- RI_T_STEP = 1<<0, /* Timeout Timer Step */
-};
-
/* MAC Arbiter Registers */
/* B3_MA_TO_CTRL 16 bit MAC Arbiter Timeout Ctrl Reg */
enum {
@@ -452,19 +376,6 @@ enum {
#define SK_PKT_TO_MAX 0xffff /* Maximum value */
#define SK_RI_TO_53 36 /* RAM interface timeout */
-
-/* B3_MA_RC_CTRL 16 bit MAC Arbiter Recovery Ctrl Reg */
-enum {
- MA_ENA_REC_TX2 = 1<<7, /* Enable Recovery Timer TX2 */
- MA_DIS_REC_TX2 = 1<<6, /* Disable Recovery Timer TX2 */
- MA_ENA_REC_TX1 = 1<<5, /* Enable Recovery Timer TX1 */
- MA_DIS_REC_TX1 = 1<<4, /* Disable Recovery Timer TX1 */
- MA_ENA_REC_RX2 = 1<<3, /* Enable Recovery Timer RX2 */
- MA_DIS_REC_RX2 = 1<<2, /* Disable Recovery Timer RX2 */
- MA_ENA_REC_RX1 = 1<<1, /* Enable Recovery Timer RX1 */
- MA_DIS_REC_RX1 = 1<<0, /* Disable Recovery Timer RX1 */
-};
-
/* Packet Arbiter Registers */
/* B3_PA_CTRL 16 bit Packet Arbiter Ctrl Register */
enum {
@@ -618,8 +529,7 @@ enum {
enum {
PHY_ADDR_XMAC = 0<<8,
PHY_ADDR_BCOM = 1<<8,
- PHY_ADDR_LONE = 3<<8,
- PHY_ADDR_NAT = 0<<8,
+
/* GPHY address (bits 15..11 of SMI control reg) */
PHY_ADDR_MARV = 0,
};
@@ -1151,54 +1061,6 @@ enum {
PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
};
-/* Level One-PHY Registers, indirect addressed over XMAC */
-enum {
- PHY_LONE_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
- PHY_LONE_STAT = 0x01,/* 16 bit r/o PHY Status Register */
- PHY_LONE_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
- PHY_LONE_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
- PHY_LONE_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
- PHY_LONE_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
- PHY_LONE_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_LONE_NEPG = 0x07,/* 16 bit r/w Next Page Register */
- PHY_LONE_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
- /* Level One-specific registers */
- PHY_LONE_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
- PHY_LONE_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
- PHY_LONE_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
- PHY_LONE_PORT_CFG = 0x10,/* 16 bit r/w Port Configuration Reg*/
- PHY_LONE_Q_STAT = 0x11,/* 16 bit r/o Quick Status Reg */
- PHY_LONE_INT_ENAB = 0x12,/* 16 bit r/w Interrupt Enable Reg */
- PHY_LONE_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
- PHY_LONE_LED_CFG = 0x14,/* 16 bit r/w LED Configuration Reg */
- PHY_LONE_PORT_CTRL = 0x15,/* 16 bit r/w Port Control Reg */
- PHY_LONE_CIM = 0x16,/* 16 bit r/o CIM Reg */
-};
-
-/* National-PHY Registers, indirect addressed over XMAC */
-enum {
- PHY_NAT_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
- PHY_NAT_STAT = 0x01,/* 16 bit r/w PHY Status Register */
- PHY_NAT_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
- PHY_NAT_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
- PHY_NAT_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
- PHY_NAT_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Ability Reg */
- PHY_NAT_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_NAT_NEPG = 0x07,/* 16 bit r/w Next Page Register */
- PHY_NAT_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner Reg */
- /* National-specific registers */
- PHY_NAT_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
- PHY_NAT_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
- PHY_NAT_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Register */
- PHY_NAT_EXT_CTRL1 = 0x10,/* 16 bit r/o Extended Control Reg1 */
- PHY_NAT_Q_STAT1 = 0x11,/* 16 bit r/o Quick Status Reg1 */
- PHY_NAT_10B_OP = 0x12,/* 16 bit r/o 10Base-T Operations Reg */
- PHY_NAT_EXT_CTRL2 = 0x13,/* 16 bit r/o Extended Control Reg1 */
- PHY_NAT_Q_STAT2 = 0x14,/* 16 bit r/o Quick Status Reg2 */
-
- PHY_NAT_PHY_ADDR = 0x19,/* 16 bit r/o PHY Address Register */
-};
-
enum {
PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
@@ -1253,8 +1115,29 @@ enum {
PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
};
+/* Advertisement register bits */
enum {
PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
+ PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
+ PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */
+
+ PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */
+ PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */
+ PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */
+ PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */
+ PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */
+ PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */
+ PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */
+ PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */
+ PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
+ PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
+ PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL |
+ PHY_AN_100HALF | PHY_AN_100FULL,
+};
+
+/* Xmac Specific */
+enum {
+ PHY_X_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
PHY_X_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
PHY_X_AN_RFB = 3<<12,/* Bit 13..12: Remote Fault Bits */
@@ -1263,82 +1146,6 @@ enum {
PHY_X_AN_FD = 1<<5, /* Bit 5: Full Duplex */
};
-enum {
- PHY_B_AN_RF = 1<<13, /* Bit 13: Remote Fault */
-
- PHY_B_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
- PHY_B_AN_PC = 1<<10, /* Bit 10: Pause Capable */
- PHY_B_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
-};
-
-enum {
- PHY_L_AN_RF = 1<<13, /* Bit 13: Remote Fault */
- /* Bit 12: reserved */
- PHY_L_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
- PHY_L_AN_PC = 1<<10, /* Bit 10: Pause Capable */
-
- PHY_L_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
-};
-
-/* PHY_NAT_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement */
-/* PHY_NAT_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/
-/* PHY_AN_NXT_PG (see XMAC) Bit 15: Request Next Page */
-enum {
- PHY_N_AN_RF = 1<<13, /* Bit 13: Remote Fault */
-
- PHY_N_AN_100F = 1<<11, /* Bit 11: 100Base-T2 FD Support */
- PHY_N_AN_100H = 1<<10, /* Bit 10: 100Base-T2 HD Support */
-
- PHY_N_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
-};
-
-/* field type definition for PHY_x_AN_SEL */
-enum {
- PHY_SEL_TYPE = 1, /* 00001 = Ethernet */
-};
-
-enum {
- PHY_ANE_LP_NP = 1<<3, /* Bit 3: Link Partner can Next Page */
- PHY_ANE_LOC_NP = 1<<2, /* Bit 2: Local PHY can Next Page */
- PHY_ANE_RX_PG = 1<<1, /* Bit 1: Page Received */
-};
-
-enum {
- PHY_ANE_PAR_DF = 1<<4, /* Bit 4: Parallel Detection Fault */
-
- PHY_ANE_LP_CAP = 1<<0, /* Bit 0: Link Partner Auto-Neg. Cap. */
-};
-
-enum {
- PHY_NP_MORE = 1<<15, /* Bit 15: More, Next Pages to follow */
- PHY_NP_ACK1 = 1<<14, /* Bit 14: (ro) Ack1, for receiving a message */
- PHY_NP_MSG_VAL = 1<<13, /* Bit 13: Message Page valid */
- PHY_NP_ACK2 = 1<<12, /* Bit 12: Ack2, comply with msg content */
- PHY_NP_TOG = 1<<11, /* Bit 11: Toggle Bit, ensure sync */
- PHY_NP_MSG = 0x07ff, /* Bit 10..0: Message from/to Link Partner */
-};
-
-enum {
- PHY_X_EX_FD = 1<<15, /* Bit 15: Device Supports Full Duplex */
- PHY_X_EX_HD = 1<<14, /* Bit 14: Device Supports Half Duplex */
-};
-
-enum {
- PHY_X_RS_PAUSE = 3<<7,/* Bit 8..7: selected Pause Mode */
- PHY_X_RS_HD = 1<<6, /* Bit 6: Half Duplex Mode selected */
- PHY_X_RS_FD = 1<<5, /* Bit 5: Full Duplex Mode selected */
- PHY_X_RS_ABLMIS = 1<<4, /* Bit 4: duplex or pause cap mismatch */
- PHY_X_RS_PAUMIS = 1<<3, /* Bit 3: pause capability mismatch */
-};
-
-/** Remote Fault Bits (PHY_X_AN_RFB) encoding */
-enum {
- X_RFB_OK = 0<<12,/* Bit 13..12 No errors, Link OK */
- X_RFB_LF = 1<<12, /* Bit 13..12 Link Failure */
- X_RFB_OFF = 2<<12,/* Bit 13..12 Offline */
- X_RFB_AN_ERR = 3<<12,/* Bit 13..12 Auto-Negotiation Error */
-};
-
/* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
enum {
PHY_X_P_NO_PAUSE = 0<<7,/* Bit 8..7: no Pause Mode */
@@ -1495,166 +1302,6 @@ enum {
PHY_B_RES_1000HD = 6<<8,/* Bit 10..8: 1000Base-T Half Dup. */
};
-/*
- * Level One-Specific
- */
-/***** PHY_LONE_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
-enum {
- PHY_L_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
- PHY_L_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
- PHY_L_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
- PHY_L_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
- PHY_L_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
- PHY_L_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
-};
-
-/***** PHY_LONE_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
-enum {
- PHY_L_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
- PHY_L_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
- PHY_L_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
- PHY_L_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
- PHY_L_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
- PHY_L_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
-
- PHY_L_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
-
-/***** PHY_LONE_EXT_STAT 16 bit r/o Extended Status Register *****/
- PHY_L_ES_X_FD_CAP = 1<<15, /* Bit 15: 1000Base-X FD capable */
- PHY_L_ES_X_HD_CAP = 1<<14, /* Bit 14: 1000Base-X HD capable */
- PHY_L_ES_T_FD_CAP = 1<<13, /* Bit 13: 1000Base-T FD capable */
- PHY_L_ES_T_HD_CAP = 1<<12, /* Bit 12: 1000Base-T HD capable */
-};
-
-/***** PHY_LONE_PORT_CFG 16 bit r/w Port Configuration Reg *****/
-enum {
- PHY_L_PC_REP_MODE = 1<<15, /* Bit 15: Repeater Mode */
-
- PHY_L_PC_TX_DIS = 1<<13, /* Bit 13: Tx output Disabled */
- PHY_L_PC_BY_SCR = 1<<12, /* Bit 12: Bypass Scrambler */
- PHY_L_PC_BY_45 = 1<<11, /* Bit 11: Bypass 4B5B-Decoder */
- PHY_L_PC_JAB_DIS = 1<<10, /* Bit 10: Jabber Disabled */
- PHY_L_PC_SQE = 1<<9, /* Bit 9: Enable Heartbeat */
- PHY_L_PC_TP_LOOP = 1<<8, /* Bit 8: TP Loopback */
- PHY_L_PC_SSS = 1<<7, /* Bit 7: Smart Speed Selection */
- PHY_L_PC_FIFO_SIZE = 1<<6, /* Bit 6: FIFO Size */
- PHY_L_PC_PRE_EN = 1<<5, /* Bit 5: Preamble Enable */
- PHY_L_PC_CIM = 1<<4, /* Bit 4: Carrier Integrity Mon */
- PHY_L_PC_10_SER = 1<<3, /* Bit 3: Use Serial Output */
- PHY_L_PC_ANISOL = 1<<2, /* Bit 2: Unisolate Port */
- PHY_L_PC_TEN_BIT = 1<<1, /* Bit 1: 10bit iface mode on */
- PHY_L_PC_ALTCLOCK = 1<<0, /* Bit 0: (ro) ALTCLOCK Mode on */
-};
-
-/***** PHY_LONE_Q_STAT 16 bit r/o Quick Status Reg *****/
-enum {
- PHY_L_QS_D_RATE = 3<<14,/* Bit 15..14: Data Rate */
- PHY_L_QS_TX_STAT = 1<<13, /* Bit 13: Transmitting */
- PHY_L_QS_RX_STAT = 1<<12, /* Bit 12: Receiving */
- PHY_L_QS_COL_STAT = 1<<11, /* Bit 11: Collision */
- PHY_L_QS_L_STAT = 1<<10, /* Bit 10: Link is up */
- PHY_L_QS_DUP_MOD = 1<<9, /* Bit 9: Full/Half Duplex */
- PHY_L_QS_AN = 1<<8, /* Bit 8: AutoNeg is On */
- PHY_L_QS_AN_C = 1<<7, /* Bit 7: AN is Complete */
- PHY_L_QS_LLE = 7<<4,/* Bit 6..4: Line Length Estim. */
- PHY_L_QS_PAUSE = 1<<3, /* Bit 3: LP advertised Pause */
- PHY_L_QS_AS_PAUSE = 1<<2, /* Bit 2: LP adv. asym. Pause */
- PHY_L_QS_ISOLATE = 1<<1, /* Bit 1: CIM Isolated */
- PHY_L_QS_EVENT = 1<<0, /* Bit 0: Event has occurred */
-};
-
-/***** PHY_LONE_INT_ENAB 16 bit r/w Interrupt Enable Reg *****/
-/***** PHY_LONE_INT_STAT 16 bit r/o Interrupt Status Reg *****/
-enum {
- PHY_L_IS_AN_F = 1<<13, /* Bit 13: Auto-Negotiation fault */
- PHY_L_IS_CROSS = 1<<11, /* Bit 11: Crossover used */
- PHY_L_IS_POL = 1<<10, /* Bit 10: Polarity correct. used */
- PHY_L_IS_SS = 1<<9, /* Bit 9: Smart Speed Downgrade */
- PHY_L_IS_CFULL = 1<<8, /* Bit 8: Counter Full */
- PHY_L_IS_AN_C = 1<<7, /* Bit 7: AutoNeg Complete */
- PHY_L_IS_SPEED = 1<<6, /* Bit 6: Speed Changed */
- PHY_L_IS_DUP = 1<<5, /* Bit 5: Duplex Changed */
- PHY_L_IS_LS = 1<<4, /* Bit 4: Link Status Changed */
- PHY_L_IS_ISOL = 1<<3, /* Bit 3: Isolate Occured */
- PHY_L_IS_MDINT = 1<<2, /* Bit 2: (ro) STAT: MII Int Pending */
- PHY_L_IS_INTEN = 1<<1, /* Bit 1: ENAB: Enable IRQs */
- PHY_L_IS_FORCE = 1<<0, /* Bit 0: ENAB: Force Interrupt */
-};
-
-/* int. mask */
-#define PHY_L_DEF_MSK (PHY_L_IS_LS | PHY_L_IS_ISOL | PHY_L_IS_INTEN)
-
-/***** PHY_LONE_LED_CFG 16 bit r/w LED Configuration Reg *****/
-enum {
- PHY_L_LC_LEDC = 3<<14,/* Bit 15..14: Col/Blink/On/Off */
- PHY_L_LC_LEDR = 3<<12,/* Bit 13..12: Rx/Blink/On/Off */
- PHY_L_LC_LEDT = 3<<10,/* Bit 11..10: Tx/Blink/On/Off */
- PHY_L_LC_LEDG = 3<<8,/* Bit 9..8: Giga/Blink/On/Off */
- PHY_L_LC_LEDS = 3<<6,/* Bit 7..6: 10-100/Blink/On/Off */
- PHY_L_LC_LEDL = 3<<4,/* Bit 5..4: Link/Blink/On/Off */
- PHY_L_LC_LEDF = 3<<2,/* Bit 3..2: Duplex/Blink/On/Off */
- PHY_L_LC_PSTRECH= 1<<1, /* Bit 1: Strech LED Pulses */
- PHY_L_LC_FREQ = 1<<0, /* Bit 0: 30/100 ms */
-};
-
-/***** PHY_LONE_PORT_CTRL 16 bit r/w Port Control Reg *****/
-enum {
- PHY_L_PC_TX_TCLK = 1<<15, /* Bit 15: Enable TX_TCLK */
- PHY_L_PC_ALT_NP = 1<<13, /* Bit 14: Alternate Next Page */
- PHY_L_PC_GMII_ALT= 1<<12, /* Bit 13: Alternate GMII driver */
- PHY_L_PC_TEN_CRS = 1<<10, /* Bit 10: Extend CRS*/
-};
-
-/***** PHY_LONE_CIM 16 bit r/o CIM Reg *****/
-enum {
- PHY_L_CIM_ISOL = 0xff<<8,/* Bit 15..8: Isolate Count */
- PHY_L_CIM_FALSE_CAR = 0xff, /* Bit 7..0: False Carrier Count */
-};
-
-/*
- * Pause Bits (PHY_L_AN_ASP and PHY_L_AN_PC) encoding
- */
-enum {
- PHY_L_P_NO_PAUSE= 0<<10,/* Bit 11..10: no Pause Mode */
- PHY_L_P_SYM_MD = 1<<10, /* Bit 11..10: symmetric Pause Mode */
- PHY_L_P_ASYM_MD = 2<<10,/* Bit 11..10: asymmetric Pause Mode */
- PHY_L_P_BOTH_MD = 3<<10,/* Bit 11..10: both Pause Mode */
-};
-
-/*
- * National-Specific
- */
-/***** PHY_NAT_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
-enum {
- PHY_N_1000C_TEST= 7<<13,/* Bit 15..13: Test Modes */
- PHY_N_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
- PHY_N_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
- PHY_N_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
- PHY_N_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
- PHY_N_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
- PHY_N_1000C_APC = 1<<7, /* Bit 7: Asymmetric Pause Cap. */};
-
-
-/***** PHY_NAT_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
-enum {
- PHY_N_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
- PHY_N_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
- PHY_N_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
- PHY_N_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status*/
- PHY_N_1000S_LP_FD= 1<<11, /* Bit 11: Link Partner can FD */
- PHY_N_1000S_LP_HD= 1<<10, /* Bit 10: Link Partner can HD */
- PHY_N_1000C_LP_APC= 1<<9, /* Bit 9: LP Asym. Pause Cap. */
- PHY_N_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
-};
-
-/***** PHY_NAT_EXT_STAT 16 bit r/o Extended Status Register *****/
-enum {
- PHY_N_ES_X_FD_CAP= 1<<15, /* Bit 15: 1000Base-X FD capable */
- PHY_N_ES_X_HD_CAP= 1<<14, /* Bit 14: 1000Base-X HD capable */
- PHY_N_ES_T_FD_CAP= 1<<13, /* Bit 13: 1000Base-T FD capable */
- PHY_N_ES_T_HD_CAP= 1<<12, /* Bit 12: 1000Base-T HD capable */
-};
-
/** Marvell-Specific */
enum {
PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
@@ -2540,10 +2187,6 @@ enum {
};
-/* XM_PHY_ADDR 16 bit r/w PHY Address Register */
-#define XM_PHY_ADDR_SZ 0x1f /* Bit 4..0: PHY Address bits */
-
-
/* XM_GP_PORT 32 bit r/w General Purpose Port Register */
enum {
XM_GP_ANIP = 1<<6, /* Bit 6: (ro) Auto-Neg. in progress */
@@ -2855,7 +2498,6 @@ struct skge_port {
static inline u32 skge_read32(const struct skge_hw *hw, int reg)
{
return readl(hw->regs + reg);
-
}
static inline u16 skge_read16(const struct skge_hw *hw, int reg)