aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/arm/mach-omap2/board-overo.c1
-rw-r--r--arch/arm/mach-omap2/cm.h6
-rw-r--r--arch/arm/mach-omap2/pm.h3
-rw-r--r--arch/arm/mach-omap2/pm24xx.c2
-rw-r--r--arch/arm/mach-omap2/pm34xx.c51
-rw-r--r--arch/arm/mach-omap2/serial.c197
-rw-r--r--arch/arm/plat-omap/cpu-omap.c8
-rw-r--r--arch/arm/plat-omap/gpio.c6
-rw-r--r--arch/arm/plat-omap/include/mach/serial.h1
9 files changed, 197 insertions, 78 deletions
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index a76e6b7afe6..6bce23004aa 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -52,6 +52,7 @@
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
+#define OVERO_GPIO_PENDOWN 114
#define OVERO_GPIO_BT_NRESET 164
#define OVERO_GPIO_USBH_CPEN 168
#define OVERO_GPIO_USBH_NRESET 183
diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h
index 1d3c93bf86d..f3c91a1ca39 100644
--- a/arch/arm/mach-omap2/cm.h
+++ b/arch/arm/mach-omap2/cm.h
@@ -29,9 +29,9 @@
* These registers appear once per CM module.
*/
-#define OMAP3430_CM_REVISION OMAP_CM_REGADDR(OCP_MOD, 0x0000)
-#define OMAP3430_CM_SYSCONFIG OMAP_CM_REGADDR(OCP_MOD, 0x0010)
-#define OMAP3430_CM_POLCTRL OMAP_CM_REGADDR(OCP_MOD, 0x009c)
+#define OMAP3430_CM_REVISION OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000)
+#define OMAP3430_CM_SYSCONFIG OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010)
+#define OMAP3430_CM_POLCTRL OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c)
#define OMAP3_CM_CLKOUT_CTRL_OFFSET 0x0070
#define OMAP3430_CM_CLKOUT_CTRL OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070)
diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
index f7b3baf7667..21201cd4117 100644
--- a/arch/arm/mach-omap2/pm.h
+++ b/arch/arm/mach-omap2/pm.h
@@ -11,9 +11,6 @@
#ifndef __ARCH_ARM_MACH_OMAP2_PM_H
#define __ARCH_ARM_MACH_OMAP2_PM_H
-extern int omap2_pm_init(void);
-extern int omap3_pm_init(void);
-
#ifdef CONFIG_PM_DEBUG
extern void omap2_pm_dump(int mode, int resume, unsigned int us);
extern int omap2_pm_debug;
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index db1025562fb..528dbdc26e2 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -470,7 +470,7 @@ static void __init prcm_setup_regs(void)
WKUP_MOD, PM_WKEN);
}
-int __init omap2_pm_init(void)
+static int __init omap2_pm_init(void)
{
u32 l;
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 841d4c5ed8b..488d595d8e4 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -39,7 +39,9 @@
struct power_state {
struct powerdomain *pwrdm;
u32 next_state;
+#ifdef CONFIG_SUSPEND
u32 saved_state;
+#endif
struct list_head node;
};
@@ -293,6 +295,9 @@ out:
local_irq_enable();
}
+#ifdef CONFIG_SUSPEND
+static suspend_state_t suspend_state;
+
static int omap3_pm_prepare(void)
{
disable_hlt();
@@ -321,7 +326,6 @@ static int omap3_pm_suspend(void)
restore:
/* Restore next_pwrsts */
list_for_each_entry(pwrst, &pwrst_list, node) {
- set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
if (state > pwrst->next_state) {
printk(KERN_INFO "Powerdomain (%s) didn't enter "
@@ -329,6 +333,7 @@ restore:
pwrst->pwrdm->name, pwrst->next_state);
ret = -1;
}
+ set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
}
if (ret)
printk(KERN_ERR "Could not enter target state in pm_suspend\n");
@@ -339,11 +344,11 @@ restore:
return ret;
}
-static int omap3_pm_enter(suspend_state_t state)
+static int omap3_pm_enter(suspend_state_t unused)
{
int ret = 0;
- switch (state) {
+ switch (suspend_state) {
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
ret = omap3_pm_suspend();
@@ -360,12 +365,30 @@ static void omap3_pm_finish(void)
enable_hlt();
}
+/* Hooks to enable / disable UART interrupts during suspend */
+static int omap3_pm_begin(suspend_state_t state)
+{
+ suspend_state = state;
+ omap_uart_enable_irqs(0);
+ return 0;
+}
+
+static void omap3_pm_end(void)
+{
+ suspend_state = PM_SUSPEND_ON;
+ omap_uart_enable_irqs(1);
+ return;
+}
+
static struct platform_suspend_ops omap_pm_ops = {
+ .begin = omap3_pm_begin,
+ .end = omap3_pm_end,
.prepare = omap3_pm_prepare,
.enter = omap3_pm_enter,
.finish = omap3_pm_finish,
.valid = suspend_valid_only_mem,
};
+#endif /* CONFIG_SUSPEND */
/**
@@ -613,6 +636,24 @@ static void __init prcm_setup_regs(void)
/* Clear any pending PRCM interrupts */
prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ /* Don't attach IVA interrupts */
+ prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
+ prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
+ prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
+ prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
+
+ /* Clear any pending 'reset' flags */
+ prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST);
+
+ /* Clear any pending PRCM interrupts */
+ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
omap3_iva_idle();
omap3_d2d_idle();
}
@@ -652,7 +693,7 @@ static int __init clkdms_setup(struct clockdomain *clkdm)
return 0;
}
-int __init omap3_pm_init(void)
+static int __init omap3_pm_init(void)
{
struct power_state *pwrst, *tmp;
int ret;
@@ -692,7 +733,9 @@ int __init omap3_pm_init(void)
_omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
omap34xx_cpu_suspend_sz);
+#ifdef CONFIG_SUSPEND
suspend_set_ops(&omap_pm_ops);
+#endif /* CONFIG_SUSPEND */
pm_idle = omap3_pm_idle;
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index b094c15bfe4..a7421a50410 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -54,6 +54,7 @@ struct omap_uart_state {
struct plat_serial8250_port *p;
struct list_head node;
+ struct platform_device pdev;
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
int context_valid;
@@ -68,10 +69,9 @@ struct omap_uart_state {
#endif
};
-static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS];
static LIST_HEAD(uart_list);
-static struct plat_serial8250_port serial_platform_data[] = {
+static struct plat_serial8250_port serial_platform_data0[] = {
{
.membase = IO_ADDRESS(OMAP_UART1_BASE),
.mapbase = OMAP_UART1_BASE,
@@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
+ .flags = 0
+ }
+};
+
+static struct plat_serial8250_port serial_platform_data1[] = {
+ {
.membase = IO_ADDRESS(OMAP_UART2_BASE),
.mapbase = OMAP_UART2_BASE,
.irq = 73,
@@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
+ .flags = 0
+ }
+};
+
+static struct plat_serial8250_port serial_platform_data2[] = {
+ {
.membase = IO_ADDRESS(OMAP_UART3_BASE),
.mapbase = OMAP_UART3_BASE,
.irq = 74,
@@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
clk_disable(uart->fck);
}
+static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
+{
+ /* Set wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ u32 v = __raw_readl(uart->wk_en);
+ v |= uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are set */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v = omap_ctrl_readw(uart->padconf);
+ v |= OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+}
+
+static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
+{
+ /* Clear wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ u32 v = __raw_readl(uart->wk_en);
+ v &= ~uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are cleared */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v = omap_ctrl_readw(uart->padconf);
+ v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+}
+
static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
int enable)
{
@@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
static void omap_uart_allow_sleep(struct omap_uart_state *uart)
{
+ if (device_may_wakeup(&uart->pdev.dev))
+ omap_uart_enable_wakeup(uart);
+ else
+ omap_uart_disable_wakeup(uart);
+
if (!uart->clocked)
return;
@@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num)
/* Check for normal UART wakeup */
if (__raw_readl(uart->wk_st) & uart->wk_mask)
omap_uart_block_sleep(uart);
-
return;
}
}
@@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
return IRQ_NONE;
}
-static u32 sleep_timeout = DEFAULT_TIMEOUT;
-
static void omap_uart_idle_init(struct omap_uart_state *uart)
{
- u32 v;
struct plat_serial8250_port *p = uart->p;
int ret;
uart->can_sleep = 0;
- uart->timeout = sleep_timeout;
+ uart->timeout = DEFAULT_TIMEOUT;
setup_timer(&uart->timer, omap_uart_idle_timer,
(unsigned long) uart);
mod_timer(&uart->timer, jiffies + uart->timeout);
@@ -413,76 +460,101 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
uart->padconf = 0;
}
- /* Set wake-enable bit */
- if (uart->wk_en && uart->wk_mask) {
- v = __raw_readl(uart->wk_en);
- v |= uart->wk_mask;
- __raw_writel(v, uart->wk_en);
- }
-
- /* Ensure IOPAD wake-enables are set */
- if (cpu_is_omap34xx() && uart->padconf) {
- u16 v;
-
- v = omap_ctrl_readw(uart->padconf);
- v |= OMAP3_PADCONF_WAKEUPENABLE0;
- omap_ctrl_writew(v, uart->padconf);
- }
-
p->flags |= UPF_SHARE_IRQ;
ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED,
"serial idle", (void *)uart);
WARN_ON(ret);
}
-static ssize_t sleep_timeout_show(struct kobject *kobj,
- struct kobj_attribute *attr,
+void omap_uart_enable_irqs(int enable)
+{
+ int ret;
+ struct omap_uart_state *uart;
+
+ list_for_each_entry(uart, &uart_list, node) {
+ if (enable)
+ ret = request_irq(uart->p->irq, omap_uart_interrupt,
+ IRQF_SHARED, "serial idle", (void *)uart);
+ else
+ free_irq(uart->p->irq, (void *)uart);
+ }
+}
+
+static ssize_t sleep_timeout_show(struct device *dev,
+ struct device_attribute *attr,
char *buf)
{
- return sprintf(buf, "%u\n", sleep_timeout / HZ);
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_uart_state *uart = container_of(pdev,
+ struct omap_uart_state, pdev);
+
+ return sprintf(buf, "%u\n", uart->timeout / HZ);
}
-static ssize_t sleep_timeout_store(struct kobject *kobj,
- struct kobj_attribute *attr,
+static ssize_t sleep_timeout_store(struct device *dev,
+ struct device_attribute *attr,
const char *buf, size_t n)
{
- struct omap_uart_state *uart;
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_uart_state *uart = container_of(pdev,
+ struct omap_uart_state, pdev);
unsigned int value;
if (sscanf(buf, "%u", &value) != 1) {
printk(KERN_ERR "sleep_timeout_store: Invalid value\n");
return -EINVAL;
}
- sleep_timeout = value * HZ;
- list_for_each_entry(uart, &uart_list, node) {
- uart->timeout = sleep_timeout;
- if (uart->timeout)
- mod_timer(&uart->timer, jiffies + uart->timeout);
- else
- /* A zero value means disable timeout feature */
- omap_uart_block_sleep(uart);
- }
+
+ uart->timeout = value * HZ;
+ if (uart->timeout)
+ mod_timer(&uart->timer, jiffies + uart->timeout);
+ else
+ /* A zero value means disable timeout feature */
+ omap_uart_block_sleep(uart);
+
return n;
}
-static struct kobj_attribute sleep_timeout_attr =
- __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
-
+DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
+#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
#else
static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
+#define DEV_CREATE_FILE(dev, attr)
#endif /* CONFIG_PM */
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
+static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = {
+ {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = serial_platform_data0,
+ },
+ },
+ }, {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM1,
+ .dev = {
+ .platform_data = serial_platform_data1,
+ },
+ },
+ }, {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM2,
+ .dev = {
+ .platform_data = serial_platform_data2,
+ },
+ },
},
};
void __init omap_serial_init(void)
{
- int i, err;
+ int i;
const struct omap_uart_config *info;
char name[16];
@@ -496,14 +568,12 @@ void __init omap_serial_init(void)
if (info == NULL)
return;
- if (cpu_is_omap44xx()) {
- for (i = 0; i < OMAP_MAX_NR_PORTS; i++)
- serial_platform_data[i].irq += 32;
- }
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
- struct plat_serial8250_port *p = serial_platform_data + i;
struct omap_uart_state *uart = &omap_uart[i];
+ struct platform_device *pdev = &uart->pdev;
+ struct device *dev = &pdev->dev;
+ struct plat_serial8250_port *p = dev->platform_data;
if (!(info->enabled_uarts & (1 << i))) {
p->membase = NULL;
@@ -531,20 +601,21 @@ void __init omap_serial_init(void)
uart->num = i;
p->private_data = uart;
uart->p = p;
- list_add(&uart->node, &uart_list);
+ list_add_tail(&uart->node, &uart_list);
+
+ if (cpu_is_omap44xx())
+ p->irq += 32;
omap_uart_enable_clocks(uart);
omap_uart_reset(uart);
omap_uart_idle_init(uart);
- }
-
- err = platform_device_register(&serial_device);
-
-#ifdef CONFIG_PM
- if (!err)
- err = sysfs_create_file(&serial_device.dev.kobj,
- &sleep_timeout_attr.attr);
-#endif
+ if (WARN_ON(platform_device_register(pdev)))
+ continue;
+ if ((cpu_is_omap34xx() && uart->padconf) ||
+ (uart->wk_en && uart->wk_mask)) {
+ device_init_wakeup(dev, true);
+ DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout);
+ }
+ }
}
-
diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c
index 843e8af6406..1868c0d8f9b 100644
--- a/arch/arm/plat-omap/cpu-omap.c
+++ b/arch/arm/plat-omap/cpu-omap.c
@@ -78,10 +78,10 @@ static int omap_target(struct cpufreq_policy *policy,
/* Ensure desired rate is within allowed range. Some govenors
* (ondemand) will just pass target_freq=0 to get the minimum. */
- if (target_freq < policy->cpuinfo.min_freq)
- target_freq = policy->cpuinfo.min_freq;
- if (target_freq > policy->cpuinfo.max_freq)
- target_freq = policy->cpuinfo.max_freq;
+ if (target_freq < policy->min)
+ target_freq = policy->min;
+ if (target_freq > policy->max)
+ target_freq = policy->max;
freqs.old = omap_getspeed(0);
freqs.new = clk_round_rate(mpu_clk, target_freq * 1000) / 1000;
diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c
index 9c16ca8d293..9298bc0ab17 100644
--- a/arch/arm/plat-omap/gpio.c
+++ b/arch/arm/plat-omap/gpio.c
@@ -1234,6 +1234,7 @@ static void gpio_mask_irq(unsigned int irq)
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 0);
+ _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
}
static void gpio_unmask_irq(unsigned int irq)
@@ -1241,6 +1242,11 @@ static void gpio_unmask_irq(unsigned int irq)
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
unsigned int irq_mask = 1 << get_gpio_index(gpio);
+ struct irq_desc *desc = irq_to_desc(irq);
+ u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK;
+
+ if (trigger)
+ _set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
/* For level-triggered GPIOs, the clearing must be done after
* the HW source is cleared, thus after the handler has run */
diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h
index 13abd02d152..def0529c75e 100644
--- a/arch/arm/plat-omap/include/mach/serial.h
+++ b/arch/arm/plat-omap/include/mach/serial.h
@@ -59,6 +59,7 @@ extern void omap_uart_check_wakeup(void);
extern void omap_uart_prepare_suspend(void);
extern void omap_uart_prepare_idle(int num);
extern void omap_uart_resume_idle(int num);
+extern void omap_uart_enable_irqs(int enable);
#endif
#endif
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 12:59:31 +0000