aboutsummaryrefslogtreecommitdiff
path: root/Documentation/i2c/chips/gl518sm
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/i2c/chips/gl518sm')
-rw-r--r--Documentation/i2c/chips/gl518sm74
1 files changed, 0 insertions, 74 deletions
diff --git a/Documentation/i2c/chips/gl518sm b/Documentation/i2c/chips/gl518sm
deleted file mode 100644
index ce0881883bc..00000000000
--- a/Documentation/i2c/chips/gl518sm
+++ /dev/null
@@ -1,74 +0,0 @@
-Kernel driver gl518sm
-=====================
-
-Supported chips:
- * Genesys Logic GL518SM release 0x00
- Prefix: 'gl518sm'
- Addresses scanned: I2C 0x2c and 0x2d
- Datasheet: http://www.genesyslogic.com/pdf
- * Genesys Logic GL518SM release 0x80
- Prefix: 'gl518sm'
- Addresses scanned: I2C 0x2c and 0x2d
- Datasheet: http://www.genesyslogic.com/pdf
-
-Authors:
- Frodo Looijaard <frodol@dds.nl>,
- Kyösti Mälkki <kmalkki@cc.hut.fi>
- Hong-Gunn Chew <hglinux@gunnet.org>
- Jean Delvare <khali@linux-fr.org>
-
-Description
------------
-
-IMPORTANT:
-
-For the revision 0x00 chip, the in0, in1, and in2 values (+5V, +3V,
-and +12V) CANNOT be read. This is a limitation of the chip, not the driver.
-
-This driver supports the Genesys Logic GL518SM chip. There are at least
-two revision of this chip, which we call revision 0x00 and 0x80. Revision
-0x80 chips support the reading of all voltages and revision 0x00 only
-for VIN3.
-
-The GL518SM implements one temperature sensor, two fan rotation speed
-sensors, and four voltage sensors. It can report alarms through the
-computer speakers.
-
-Temperatures are measured in degrees Celsius. An alarm goes off while the
-temperature is above the over temperature limit, and has not yet dropped
-below the hysteresis limit. The alarm always reflects the current
-situation. Measurements are guaranteed between -10 degrees and +110
-degrees, with a accuracy of +/-3 degrees.
-
-Rotation speeds are reported in RPM (rotations per minute). An alarm is
-triggered if the rotation speed has dropped below a programmable limit. In
-case when you have selected to turn fan1 off, no fan1 alarm is triggered.
-
-Fan readings can be divided by a programmable divider (1, 2, 4 or 8) to
-give the readings more range or accuracy. Not all RPM values can
-accurately be represented, so some rounding is done. With a divider
-of 2, the lowest representable value is around 1900 RPM.
-
-Voltage sensors (also known as VIN sensors) report their values in volts.
-An alarm is triggered if the voltage has crossed a programmable minimum or
-maximum limit. Note that minimum in this case always means 'closest to
-zero'; this is important for negative voltage measurements. The VDD input
-measures voltages between 0.000 and 5.865 volt, with a resolution of 0.023
-volt. The other inputs measure voltages between 0.000 and 4.845 volt, with
-a resolution of 0.019 volt. Note that revision 0x00 chips do not support
-reading the current voltage of any input except for VIN3; limit setting and
-alarms work fine, though.
-
-When an alarm is triggered, you can be warned by a beeping signal through your
-computer speaker. It is possible to enable all beeping globally, or only the
-beeping for some alarms.
-
-If an alarm triggers, it will remain triggered until the hardware register
-is read at least once (except for temperature alarms). This means that the
-cause for the alarm may already have disappeared! Note that in the current
-implementation, all hardware registers are read whenever any data is read
-(unless it is less than 1.5 seconds since the last update). This means that
-you can easily miss once-only alarms.
-
-The GL518SM only updates its values each 1.5 seconds; reading it more often
-will do no harm, but will return 'old' values.