diff options
Diffstat (limited to 'arch/arm')
24 files changed, 1018 insertions, 67 deletions
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h index 809ff9ab853..77764301844 100644 --- a/arch/arm/include/asm/memory.h +++ b/arch/arm/include/asm/memory.h @@ -44,10 +44,10 @@ * The module space lives between the addresses given by TASK_SIZE * and PAGE_OFFSET - it must be within 32MB of the kernel text. */ -#define MODULE_END (PAGE_OFFSET) -#define MODULE_START (MODULE_END - 16*1048576) +#define MODULES_END (PAGE_OFFSET) +#define MODULES_VADDR (MODULES_END - 16*1048576) -#if TASK_SIZE > MODULE_START +#if TASK_SIZE > MODULES_VADDR #error Top of user space clashes with start of module space #endif @@ -56,7 +56,7 @@ * Since we use sections to map it, this macro replaces the physical address * with its virtual address while keeping offset from the base section. */ -#define XIP_VIRT_ADDR(physaddr) (MODULE_START + ((physaddr) & 0x000fffff)) +#define XIP_VIRT_ADDR(physaddr) (MODULES_VADDR + ((physaddr) & 0x000fffff)) /* * Allow 16MB-aligned ioremap pages @@ -94,8 +94,8 @@ /* * The module can be at any place in ram in nommu mode. */ -#define MODULE_END (END_MEM) -#define MODULE_START (PHYS_OFFSET) +#define MODULES_END (END_MEM) +#define MODULES_VADDR (PHYS_OFFSET) #endif /* !CONFIG_MMU */ diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h index 7aad78420f1..568020b34e3 100644 --- a/arch/arm/include/asm/system.h +++ b/arch/arm/include/asm/system.h @@ -42,6 +42,10 @@ #define CR_U (1 << 22) /* Unaligned access operation */ #define CR_XP (1 << 23) /* Extended page tables */ #define CR_VE (1 << 24) /* Vectored interrupts */ +#define CR_EE (1 << 25) /* Exception (Big) Endian */ +#define CR_TRE (1 << 28) /* TEX remap enable */ +#define CR_AFE (1 << 29) /* Access flag enable */ +#define CR_TE (1 << 30) /* Thumb exception enable */ /* * This is used to ensure the compiler did actually allocate the register we diff --git a/arch/arm/kernel/elf.c b/arch/arm/kernel/elf.c index 513f332f040..84849098c8e 100644 --- a/arch/arm/kernel/elf.c +++ b/arch/arm/kernel/elf.c @@ -21,12 +21,16 @@ int elf_check_arch(const struct elf32_hdr *x) eflags = x->e_flags; if ((eflags & EF_ARM_EABI_MASK) == EF_ARM_EABI_UNKNOWN) { + unsigned int flt_fmt; + /* APCS26 is only allowed if the CPU supports it */ if ((eflags & EF_ARM_APCS_26) && !(elf_hwcap & HWCAP_26BIT)) return 0; + flt_fmt = eflags & (EF_ARM_VFP_FLOAT | EF_ARM_SOFT_FLOAT); + /* VFP requires the supporting code */ - if ((eflags & EF_ARM_VFP_FLOAT) && !(elf_hwcap & HWCAP_VFP)) + if (flt_fmt == EF_ARM_VFP_FLOAT && !(elf_hwcap & HWCAP_VFP)) return 0; } return 1; diff --git a/arch/arm/kernel/module.c b/arch/arm/kernel/module.c index 9203ba7d58e..b8d965dcd6f 100644 --- a/arch/arm/kernel/module.c +++ b/arch/arm/kernel/module.c @@ -26,12 +26,12 @@ /* * The XIP kernel text is mapped in the module area for modules and * some other stuff to work without any indirect relocations. - * MODULE_START is redefined here and not in asm/memory.h to avoid + * MODULES_VADDR is redefined here and not in asm/memory.h to avoid * recompiling the whole kernel when CONFIG_XIP_KERNEL is turned on/off. */ extern void _etext; -#undef MODULE_START -#define MODULE_START (((unsigned long)&_etext + ~PGDIR_MASK) & PGDIR_MASK) +#undef MODULES_VADDR +#define MODULES_VADDR (((unsigned long)&_etext + ~PGDIR_MASK) & PGDIR_MASK) #endif #ifdef CONFIG_MMU @@ -43,7 +43,7 @@ void *module_alloc(unsigned long size) if (!size) return NULL; - area = __get_vm_area(size, VM_ALLOC, MODULE_START, MODULE_END); + area = __get_vm_area(size, VM_ALLOC, MODULES_VADDR, MODULES_END); if (!area) return NULL; diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 763bdbeaf68..2249049c1d5 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -429,18 +429,16 @@ void __init gpmc_init(void) gpmc_l3_clk = clk_get(NULL, ck); if (IS_ERR(gpmc_l3_clk)) { printk(KERN_ERR "Could not get GPMC clock %s\n", ck); - return -ENODEV; + BUG(); } gpmc_base = ioremap(l, SZ_4K); if (!gpmc_base) { clk_put(gpmc_l3_clk); printk(KERN_ERR "Could not get GPMC register memory\n"); - return -ENOMEM; + BUG(); } - BUG_ON(IS_ERR(gpmc_l3_clk)); - l = gpmc_read_reg(GPMC_REVISION); printk(KERN_INFO "GPMC revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f); /* Set smart idle mode and automatic L3 clock gating */ diff --git a/arch/arm/mach-s3c6400/include/mach/map.h b/arch/arm/mach-s3c6400/include/mach/map.h index 4d5cd7ee8c1..cff27d813fc 100644 --- a/arch/arm/mach-s3c6400/include/mach/map.h +++ b/arch/arm/mach-s3c6400/include/mach/map.h @@ -38,6 +38,7 @@ #define S3C_VA_UART2 S3C_VA_UARTx(2) #define S3C_VA_UART3 S3C_VA_UARTx(3) +#define S3C64XX_PA_FB (0x77100000) #define S3C64XX_PA_SYSCON (0x7E00F000) #define S3C64XX_PA_TIMER (0x7F006000) #define S3C64XX_PA_IIC0 (0x7F004000) @@ -62,5 +63,6 @@ #define S3C_PA_HSMMC2 S3C64XX_PA_HSMMC2 #define S3C_PA_IIC S3C64XX_PA_IIC0 #define S3C_PA_IIC1 S3C64XX_PA_IIC1 +#define S3C_PA_FB S3C64XX_PA_FB #endif /* __ASM_ARCH_6400_MAP_H */ diff --git a/arch/arm/mach-s3c6400/include/mach/regs-fb.h b/arch/arm/mach-s3c6400/include/mach/regs-fb.h new file mode 100644 index 00000000000..47019795ce0 --- /dev/null +++ b/arch/arm/mach-s3c6400/include/mach/regs-fb.h @@ -0,0 +1,259 @@ +/* arch/arm/mach-s3c6400/include/mach/regs-fb.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C64XX - new-style framebuffer register definitions + * + * This is the register set for the new style framebuffer interface + * found from the S3C2443 onwards and specifically the S3C64XX series + * S3C6400 and S3C6410. + * + * The file contains the cpu specific items which change between whichever + * architecture is selected. See <plat/regs-fb.h> for the core definitions + * that are the same. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* include the core definitions here, in case we really do need to + * override them at a later date. +*/ + +#include <plat/regs-fb.h> + +#define S3C_FB_MAX_WIN (5) /* number of hardware windows available. */ +#define VIDCON1_FSTATUS_EVEN (1 << 15) + +/* Video timing controls */ +#define VIDTCON0 (0x10) +#define VIDTCON1 (0x14) +#define VIDTCON2 (0x18) + +/* Window position controls */ + +#define WINCON(_win) (0x20 + ((_win) * 4)) + +/* OSD1 and OSD4 do not have register D */ + +#define VIDOSD_A(_win) (0x40 + ((_win) * 16)) +#define VIDOSD_B(_win) (0x44 + ((_win) * 16)) +#define VIDOSD_C(_win) (0x48 + ((_win) * 16)) +#define VIDOSD_D(_win) (0x4C + ((_win) * 16)) + +/* Video buffer addresses */ + +#define VIDW_BUF_START(_buff) (0xA0 + ((_buff) * 8)) +#define VIDW_BUF_START1(_buff) (0xA4 + ((_buff) * 8)) +#define VIDW_BUF_END(_buff) (0xD0 + ((_buff) * 8)) +#define VIDW_BUF_END1(_buff) (0xD4 + ((_buff) * 8)) +#define VIDW_BUF_SIZE(_buff) (0x100 + ((_buff) * 4)) + +#define VIDINTCON0 (0x130) + +#define WxKEYCONy(_win, _con) ((0x140 + ((_win) * 8)) + ((_con) * 4)) + +/* WINCONx */ + +#define WINCONx_CSCWIDTH_MASK (0x3 << 26) +#define WINCONx_CSCWIDTH_SHIFT (26) +#define WINCONx_CSCWIDTH_WIDE (0x0 << 26) +#define WINCONx_CSCWIDTH_NARROW (0x3 << 26) + +#define WINCONx_ENLOCAL (1 << 22) +#define WINCONx_BUFSTATUS (1 << 21) +#define WINCONx_BUFSEL (1 << 20) +#define WINCONx_BUFAUTOEN (1 << 19) +#define WINCONx_YCbCr (1 << 13) + +#define WINCON1_LOCALSEL_CAMIF (1 << 23) + +#define WINCON2_LOCALSEL_CAMIF (1 << 23) +#define WINCON2_BLD_PIX (1 << 6) + +#define WINCON2_ALPHA_SEL (1 << 1) +#define WINCON2_BPPMODE_MASK (0xf << 2) +#define WINCON2_BPPMODE_SHIFT (2) +#define WINCON2_BPPMODE_1BPP (0x0 << 2) +#define WINCON2_BPPMODE_2BPP (0x1 << 2) +#define WINCON2_BPPMODE_4BPP (0x2 << 2) +#define WINCON2_BPPMODE_8BPP_1232 (0x4 << 2) +#define WINCON2_BPPMODE_16BPP_565 (0x5 << 2) +#define WINCON2_BPPMODE_16BPP_A1555 (0x6 << 2) +#define WINCON2_BPPMODE_16BPP_I1555 (0x7 << 2) +#define WINCON2_BPPMODE_18BPP_666 (0x8 << 2) +#define WINCON2_BPPMODE_18BPP_A1665 (0x9 << 2) +#define WINCON2_BPPMODE_19BPP_A1666 (0xa << 2) +#define WINCON2_BPPMODE_24BPP_888 (0xb << 2) +#define WINCON2_BPPMODE_24BPP_A1887 (0xc << 2) +#define WINCON2_BPPMODE_25BPP_A1888 (0xd << 2) +#define WINCON2_BPPMODE_28BPP_A4888 (0xd << 2) + +#define WINCON3_BLD_PIX (1 << 6) + +#define WINCON3_ALPHA_SEL (1 << 1) +#define WINCON3_BPPMODE_MASK (0xf << 2) +#define WINCON3_BPPMODE_SHIFT (2) +#define WINCON3_BPPMODE_1BPP (0x0 << 2) +#define WINCON3_BPPMODE_2BPP (0x1 << 2) +#define WINCON3_BPPMODE_4BPP (0x2 << 2) +#define WINCON3_BPPMODE_16BPP_565 (0x5 << 2) +#define WINCON3_BPPMODE_16BPP_A1555 (0x6 << 2) +#define WINCON3_BPPMODE_16BPP_I1555 (0x7 << 2) +#define WINCON3_BPPMODE_18BPP_666 (0x8 << 2) +#define WINCON3_BPPMODE_18BPP_A1665 (0x9 << 2) +#define WINCON3_BPPMODE_19BPP_A1666 (0xa << 2) +#define WINCON3_BPPMODE_24BPP_888 (0xb << 2) +#define WINCON3_BPPMODE_24BPP_A1887 (0xc << 2) +#define WINCON3_BPPMODE_25BPP_A1888 (0xd << 2) +#define WINCON3_BPPMODE_28BPP_A4888 (0xd << 2) + +#define VIDINTCON0_FIFIOSEL_WINDOW2 (0x10 << 5) +#define VIDINTCON0_FIFIOSEL_WINDOW3 (0x20 << 5) +#define VIDINTCON0_FIFIOSEL_WINDOW4 (0x40 << 5) + +#define DITHMODE (0x170) +#define WINxMAP(_win) (0x180 + ((_win) * 4)) + + +#define DITHMODE_R_POS_MASK (0x3 << 5) +#define DITHMODE_R_POS_SHIFT (5) +#define DITHMODE_R_POS_8BIT (0x0 << 5) +#define DITHMODE_R_POS_6BIT (0x1 << 5) +#define DITHMODE_R_POS_5BIT (0x2 << 5) + +#define DITHMODE_G_POS_MASK (0x3 << 3) +#define DITHMODE_G_POS_SHIFT (3) +#define DITHMODE_G_POS_8BIT (0x0 << 3) +#define DITHMODE_G_POS_6BIT (0x1 << 3) +#define DITHMODE_G_POS_5BIT (0x2 << 3) + +#define DITHMODE_B_POS_MASK (0x3 << 1) +#define DITHMODE_B_POS_SHIFT (1) +#define DITHMODE_B_POS_8BIT (0x0 << 1) +#define DITHMODE_B_POS_6BIT (0x1 << 1) +#define DITHMODE_B_POS_5BIT (0x2 << 1) + +#define DITHMODE_DITH_EN (1 << 0) + +#define WPALCON (0x1A0) + +#define WPALCON_W4PAL_16BPP_A555 (1 << 8) +#define WPALCON_W3PAL_16BPP_A555 (1 << 7) +#define WPALCON_W2PAL_16BPP_A555 (1 << 6) + +/* Palette registers */ + +#define WIN2_PAL(_entry) (0x300 + ((_entry) * 2)) +#define WIN3_PAL(_entry) (0x320 + ((_entry) * 2)) +#define WIN4_PAL(_entry) (0x340 + ((_entry) * 2)) +#define WIN0_PAL(_entry) (0x400 + ((_entry) * 4)) +#define WIN1_PAL(_entry) (0x800 + ((_entry) * 4)) + +/* system specific implementation code for palette sizes, and other + * information that changes depending on which architecture is being + * compiled. +*/ + +/* return true if window _win has OSD register D */ +#define s3c_fb_has_osd_d(_win) ((_win) != 4 && (_win) != 0) + +static inline unsigned int s3c_fb_win_pal_size(unsigned int win) +{ + if (win < 2) + return 256; + if (win < 4) + return 16; + if (win == 4) + return 4; + + BUG(); /* shouldn't get here */ +} + +static inline int s3c_fb_validate_win_bpp(unsigned int win, unsigned int bpp) +{ + /* all windows can do 1/2 bpp */ + + if ((bpp == 25 || bpp == 19) && win == 0) + return 0; /* win 0 does not have 19 or 25bpp modes */ + + if (bpp == 4 && win == 4) + return 0; + + if (bpp == 8 && (win >= 3)) + return 0; /* win 3/4 cannot do 8bpp in any mode */ + + return 1; +} + +static inline unsigned int s3c_fb_pal_reg(unsigned int window, int reg) +{ + switch (window) { + case 0: return WIN0_PAL(reg); + case 1: return WIN1_PAL(reg); + case 2: return WIN2_PAL(reg); + case 3: return WIN3_PAL(reg); + case 4: return WIN4_PAL(reg); + } + + BUG(); +} + +static inline int s3c_fb_pal_is16(unsigned int window) +{ + return window > 1; +} + +struct s3c_fb_palette { + struct fb_bitfield r; + struct fb_bitfield g; + struct fb_bitfield b; + struct fb_bitfield a; +}; + +static inline void s3c_fb_init_palette(unsigned int window, + struct s3c_fb_palette *palette) +{ + if (window < 2) { + /* Windows 0/1 are 8/8/8 or A/8/8/8 */ + palette->r.offset = 16; + palette->r.length = 8; + palette->g.offset = 8; + palette->g.length = 8; + palette->b.offset = 0; + palette->b.length = 8; + } else { + /* currently we assume RGB 5/6/5 */ + palette->r.offset = 11; + palette->r.length = 5; + palette->g.offset = 5; + palette->g.length = 6; + palette->b.offset = 0; + palette->b.length = 5; + } +} + +/* Notes on per-window bpp settings + * + * Value Win0 Win1 Win2 Win3 Win 4 + * 0000 1(P) 1(P) 1(P) 1(P) 1(P) + * 0001 2(P) 2(P) 2(P) 2(P) 2(P) + * 0010 4(P) 4(P) 4(P) 4(P) -none- + * 0011 8(P) 8(P) -none- -none- -none- + * 0100 -none- 8(A232) 8(A232) -none- -none- + * 0101 16(565) 16(565) 16(565) 16(565) 16(565) + * 0110 -none- 16(A555) 16(A555) 16(A555) 16(A555) + * 0111 16(I555) 16(I565) 16(I555) 16(I555) 16(I555) + * 1000 18(666) 18(666) 18(666) 18(666) 18(666) + * 1001 -none- 18(A665) 18(A665) 18(A665) 16(A665) + * 1010 -none- 19(A666) 19(A666) 19(A666) 19(A666) + * 1011 24(888) 24(888) 24(888) 24(888) 24(888) + * 1100 -none- 24(A887) 24(A887) 24(A887) 24(A887) + * 1101 -none- 25(A888) 25(A888) 25(A888) 25(A888) + * 1110 -none- -none- -none- -none- -none- + * 1111 -none- -none- -none- -none- -none- +*/ diff --git a/arch/arm/mach-s3c6410/Kconfig b/arch/arm/mach-s3c6410/Kconfig index d00b5605100..1d501007002 100644 --- a/arch/arm/mach-s3c6410/Kconfig +++ b/arch/arm/mach-s3c6410/Kconfig @@ -25,8 +25,10 @@ config MACH_SMDK6410 select S3C_DEV_HSMMC select S3C_DEV_HSMMC1 select S3C_DEV_I2C1 + select S3C_DEV_FB select S3C6410_SETUP_SDHCI select S3C64XX_SETUP_I2C1 + select S3C64XX_SETUP_FB_24BPP help Machine support for the Samsung SMDK6410 diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c index 15c24d00a49..3c4d47145c8 100644 --- a/arch/arm/mach-s3c6410/mach-smdk6410.c +++ b/arch/arm/mach-s3c6410/mach-smdk6410.c @@ -21,12 +21,18 @@ #include <linux/platform_device.h> #include <linux/io.h> #include <linux/i2c.h> +#include <linux/fb.h> +#include <linux/gpio.h> +#include <linux/delay.h> + +#include <video/platform_lcd.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/irq.h> #include <mach/hardware.h> +#include <mach/regs-fb.h> #include <mach/map.h> #include <asm/irq.h> @@ -34,6 +40,7 @@ #include <plat/regs-serial.h> #include <plat/iic.h> +#include <plat/fb.h> #include <plat/s3c6410.h> #include <plat/clock.h> @@ -61,6 +68,67 @@ static struct s3c2410_uartcfg smdk6410_uartcfgs[] __initdata = { }, }; +/* framebuffer and LCD setup. */ + +/* GPF15 = LCD backlight control + * GPF13 => Panel power + * GPN5 = LCD nRESET signal + * PWM_TOUT1 => backlight brightness + */ + +static void smdk6410_lcd_power_set(struct plat_lcd_data *pd, + unsigned int power) +{ + if (power) { + gpio_direction_output(S3C64XX_GPF(13), 1); + gpio_direction_output(S3C64XX_GPF(15), 1); + + /* fire nRESET on power up */ + gpio_direction_output(S3C64XX_GPN(5), 0); + msleep(10); + gpio_direction_output(S3C64XX_GPN(5), 1); + msleep(1); + } else { + gpio_direction_output(S3C64XX_GPF(15), 0); + gpio_direction_output(S3C64XX_GPF(13), 0); + } +} + +static struct plat_lcd_data smdk6410_lcd_power_data = { + .set_power = smdk6410_lcd_power_set, +}; + +static struct platform_device smdk6410_lcd_powerdev = { + .name = "platform-lcd", + .dev.parent = &s3c_device_fb.dev, + .dev.platform_data = &smdk6410_lcd_power_data, +}; + +static struct s3c_fb_pd_win smdk6410_fb_win0 = { + /* this is to ensure we use win0 */ + .win_mode = { + .pixclock = 41094, + .left_margin = 8, + .right_margin = 13, + .upper_margin = 7, + .lower_margin = 5, + .hsync_len = 3, + .vsync_len = 1, + .xres = 800, + .yres = 480, + }, + .max_bpp = 32, + .default_bpp = 16, +}; + +/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */ +static struct s3c_fb_platdata smdk6410_lcd_pdata __initdata = { + .setup_gpio = s3c64xx_fb_gpio_setup_24bpp, + .win[0] = &smdk6410_fb_win0, + .vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB, + .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC, +}; + struct map_desc smdk6410_iodesc[] = {}; static struct platform_device *smdk6410_devices[] __initdata = { @@ -72,6 +140,8 @@ static struct platform_device *smdk6410_devices[] __initdata = { #endif &s3c_device_i2c0, &s3c_device_i2c1, + &s3c_device_fb, + &smdk6410_lcd_powerdev, }; static struct i2c_board_info i2c_devs0[] __initdata = { @@ -94,6 +164,7 @@ static void __init smdk6410_machine_init(void) { s3c_i2c0_set_platdata(NULL); s3c_i2c1_set_platdata(NULL); + s3c_fb_set_platdata(&smdk6410_lcd_pdata); i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0)); i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1)); diff --git a/arch/arm/mm/cache-xsc3l2.c b/arch/arm/mm/cache-xsc3l2.c index 10b1bae1a25..464de893a98 100644 --- a/arch/arm/mm/cache-xsc3l2.c +++ b/arch/arm/mm/cache-xsc3l2.c @@ -98,7 +98,7 @@ static void xsc3_l2_inv_range(unsigned long start, unsigned long end) /* * Clean and invalidate partial last cache line. */ - if (end & (CACHE_LINE_SIZE - 1)) { + if (start < end && (end & (CACHE_LINE_SIZE - 1))) { xsc3_l2_clean_pa(end & ~(CACHE_LINE_SIZE - 1)); xsc3_l2_inv_pa(end & ~(CACHE_LINE_SIZE - 1)); end &= ~(CACHE_LINE_SIZE - 1); @@ -107,7 +107,7 @@ static void xsc3_l2_inv_range(unsigned long start, unsigned long end) /* * Invalidate all full cache lines between 'start' and 'end'. */ - while (start != end) { + while (start < end) { xsc3_l2_inv_pa(start); start += CACHE_LINE_SIZE; } diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 8ba75406455..e63db11f16a 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -180,20 +180,20 @@ void adjust_cr(unsigned long mask, unsigned long set) #endif #define PROT_PTE_DEVICE L_PTE_PRESENT|L_PTE_YOUNG|L_PTE_DIRTY|L_PTE_WRITE -#define PROT_SECT_DEVICE PMD_TYPE_SECT|PMD_SECT_XN|PMD_SECT_AP_WRITE +#define PROT_SECT_DEVICE PMD_TYPE_SECT|PMD_SECT_AP_WRITE static struct mem_type mem_types[] = { [MT_DEVICE] = { /* Strongly ordered / ARMv6 shared device */ .prot_pte = PROT_PTE_DEVICE | L_PTE_MT_DEV_SHARED | L_PTE_SHARED, .prot_l1 = PMD_TYPE_TABLE, - .prot_sect = PROT_SECT_DEVICE | PMD_SECT_UNCACHED, + .prot_sect = PROT_SECT_DEVICE | PMD_SECT_S, .domain = DOMAIN_IO, }, [MT_DEVICE_NONSHARED] = { /* ARMv6 non-shared device */ .prot_pte = PROT_PTE_DEVICE | L_PTE_MT_DEV_NONSHARED, .prot_l1 = PMD_TYPE_TABLE, - .prot_sect = PROT_SECT_DEVICE | PMD_SECT_TEX(2), + .prot_sect = PROT_SECT_DEVICE, .domain = DOMAIN_IO, }, [MT_DEVICE_CACHED] = { /* ioremap_cached */ @@ -205,7 +205,7 @@ static struct mem_type mem_types[] = { [MT_DEVICE_WC] = { /* ioremap_wc */ .prot_pte = PROT_PTE_DEVICE | L_PTE_MT_DEV_WC, .prot_l1 = PMD_TYPE_TABLE, - .prot_sect = PROT_SECT_DEVICE | PMD_SECT_BUFFERABLE, + .prot_sect = PROT_SECT_DEVICE, .domain = DOMAIN_IO, }, [MT_CACHECLEAN] = { @@ -273,22 +273,23 @@ static void __init build_mem_type_table(void) #endif /* - * On non-Xscale3 ARMv5-and-older systems, use CB=01 - * (Uncached/Buffered) for ioremap_wc() mappings. On XScale3 - * and ARMv6+, use TEXCB=00100 mappings (Inner/Outer Uncacheable - * in xsc3 parlance, Uncached Normal in ARMv6 parlance). + * Strip out features not present on earlier architectures. + * Pre-ARMv5 CPUs don't have TEX bits. Pre-ARMv6 CPUs or those + * without extended page tables don't have the 'Shared' bit. */ - if (cpu_is_xsc3() || cpu_arch >= CPU_ARCH_ARMv6) { - mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_TEX(1); - mem_types[MT_DEVICE_WC].prot_sect &= ~PMD_SECT_BUFFERABLE; - } + if (cpu_arch < CPU_ARCH_ARMv5) + for (i = 0; i < ARRAY_SIZE(mem_types); i++) + mem_types[i].prot_sect &= ~PMD_SECT_TEX(7); + if ((cpu_arch < CPU_ARCH_ARMv6 || !(cr & CR_XP)) && !cpu_is_xsc3()) + for (i = 0; i < ARRAY_SIZE(mem_types); i++) + mem_types[i].prot_sect &= ~PMD_SECT_S; /* - * ARMv5 and lower, bit 4 must be set for page tables. - * (was: cache "update-able on write" bit on ARM610) - * However, Xscale cores require this bit to be cleared. + * ARMv5 and lower, bit 4 must be set for page tables (was: cache + * "update-able on write" bit on ARM610). However, Xscale and + * Xscale3 require this bit to be cleared. */ - if (cpu_is_xscale()) { + if (cpu_is_xscale() || cpu_is_xsc3()) { for (i = 0; i < ARRAY_SIZE(mem_types); i++) { mem_types[i].prot_sect &= ~PMD_BIT4; mem_types[i].prot_l1 &= ~PMD_BIT4; @@ -302,6 +303,64 @@ static void __init build_mem_type_table(void) } } + /* + * Mark the device areas according to the CPU/architecture. + */ + if (cpu_is_xsc3() || (cpu_arch >= CPU_ARCH_ARMv6 && (cr & CR_XP))) { + if (!cpu_is_xsc3()) { + /* + * Mark device regions on ARMv6+ as execute-never + * to prevent speculative instruction fetches. + */ + mem_types[MT_DEVICE].prot_sect |= PMD_SECT_XN; + mem_types[MT_DEVICE_NONSHARED].prot_sect |= PMD_SECT_XN; + mem_types[MT_DEVICE_CACHED].prot_sect |= PMD_SECT_XN; + mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_XN; + } + if (cpu_arch >= CPU_ARCH_ARMv7 && (cr & CR_TRE)) { + /* + * For ARMv7 with TEX remapping, + * - shared device is SXCB=1100 + * - nonshared device is SXCB=0100 + * - write combine device mem is SXCB=0001 + * (Uncached Normal memory) + */ + mem_types[MT_DEVICE].prot_sect |= PMD_SECT_TEX(1); + mem_types[MT_DEVICE_NONSHARED].prot_sect |= PMD_SECT_TEX(1); + mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_BUFFERABLE; + } else if (cpu_is_xsc3()) { + /* + * For Xscale3, + * - shared device is TEXCB=00101 + * - nonshared device is TEXCB=01000 + * - write combine device mem is TEXCB=00100 + * (Inner/Outer Uncacheable in xsc3 parlance) + */ + mem_types[MT_DEVICE].prot_sect |= PMD_SECT_TEX(1) | PMD_SECT_BUFFERED; + mem_types[MT_DEVICE_NONSHARED].prot_sect |= PMD_SECT_TEX(2); + mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_TEX(1); + } else { + /* + * For ARMv6 and ARMv7 without TEX remapping, + * - shared device is TEXCB=00001 + * - nonshared device is TEXCB=01000 + * - write combine device mem is TEXCB=00100 + * (Uncached Normal in ARMv6 parlance). + */ + mem_types[MT_DEVICE].prot_sect |= PMD_SECT_BUFFERED; + mem_types[MT_DEVICE_NONSHARED].prot_sect |= PMD_SECT_TEX(2); + mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_TEX(1); + } + } else { + /* + * On others, write combining is "Uncached/Buffered" + */ + mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_BUFFERABLE; + } + + /* + * Now deal with the memory-type mappings + */ cp = &cache_policies[cachepolicy]; vecs_pgprot = kern_pgprot = user_pgprot = cp->pte; @@ -317,12 +376,8 @@ static void __init build_mem_type_table(void) * Enable CPU-specific coherency if supported. * (Only available on XSC3 at the moment.) */ - if (arch_is_coherent()) { - if (cpu_is_xsc3()) { - mem_types[MT_MEMORY].prot_sect |= PMD_SECT_S; - mem_types[MT_MEMORY].prot_pte |= L_PTE_SHARED; - } - } + if (arch_is_coherent() && cpu_is_xsc3()) + mem_types[MT_MEMORY].prot_sect |= PMD_SECT_S; /* * ARMv6 and above have extended page tables. @@ -336,11 +391,6 @@ static void __init build_mem_type_table(void) mem_types[MT_MINICLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE; mem_types[MT_CACHECLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE; - /* - * Mark the device area as "shared device" - */ - mem_types[MT_DEVICE].prot_sect |= PMD_SECT_BUFFERED; - #ifdef CONFIG_SMP /* * Mark memory with the "shared" attribute for SMP systems @@ -360,9 +410,6 @@ static void __init build_mem_type_table(void) mem_types[MT_LOW_VECTORS].prot_pte |= vecs_pgprot; mem_types[MT_HIGH_VECTORS].prot_pte |= vecs_pgprot; - if (cpu_arch < CPU_ARCH_ARMv5) - mem_types[MT_MINICLEAN].prot_sect &= ~PMD_SECT_TEX(1); - pgprot_user = __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | user_pgprot); pgprot_kernel = __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY | L_PTE_WRITE | @@ -654,7 +701,7 @@ static inline void prepare_page_table(struct meminfo *mi) /* * Clear out all the mappings below the kernel image. */ - for (addr = 0; addr < MODULE_START; addr += PGDIR_SIZE) + for (addr = 0; addr < MODULES_VADDR; addr += PGDIR_SIZE) pmd_clear(pmd_off_k(addr)); #ifdef CONFIG_XIP_KERNEL @@ -766,7 +813,7 @@ static void __init devicemaps_init(struct machine_desc *mdesc) */ #ifdef CONFIG_XIP_KERNEL map.pfn = __phys_to_pfn(CONFIG_XIP_PHYS_ADDR & SECTION_MASK); - map.virtual = MODULE_START; + map.virtual = MODULES_VADDR; map.length = ((unsigned long)&_etext - map.virtual + ~SECTION_MASK) & SECTION_MASK; map.type = MT_ROM; create_mapping(&map); diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index 07f82db7094..4d3c0a73e7f 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -115,7 +115,7 @@ ENTRY(cpu_v7_set_pte_ext) orr r3, r3, r2 orr r3, r3, #PTE_EXT_AP0 | 2 - tst r2, #1 << 4 + tst r1, #1 << 4 orrne r3, r3, #PTE_EXT_TEX(1) tst r1, #L_PTE_WRITE @@ -192,11 +192,11 @@ __v7_setup: mov pc, lr @ return to head.S:__ret ENDPROC(__v7_setup) - /* - * V X F I D LR - * .... ...E PUI. .T.T 4RVI ZFRS BLDP WCAM - * rrrr rrrx xxx0 0101 xxxx xxxx x111 xxxx < forced - * 0 110 0011 1.00 .111 1101 < we want + /* AT + * TFR EV X F I D LR + * .EEE ..EE PUI. .T.T 4RVI ZFRS BLDP WCAM + * rxxx rrxx xxx0 0101 xxxx xxxx x111 xxxx < forced + * 1 0 110 0011 1.00 .111 1101 < we want */ .type v7_crval, #object v7_crval: diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c index bf6a10c5fc4..be6aab9c683 100644 --- a/arch/arm/plat-omap/clock.c +++ b/arch/arm/plat-omap/clock.c @@ -428,23 +428,23 @@ static int clk_debugfs_register_one(struct clk *c) if (c->id != 0) sprintf(p, ":%d", c->id); d = debugfs_create_dir(s, pa ? pa->dent : clk_debugfs_root); - if (IS_ERR(d)) - return PTR_ERR(d); + if (!d) + return -ENOMEM; c->dent = d; d = debugfs_create_u8("usecount", S_IRUGO, c->dent, (u8 *)&c->usecount); - if (IS_ERR(d)) { - err = PTR_ERR(d); + if (!d) { + err = -ENOMEM; goto err_out; } d = debugfs_create_u32("rate", S_IRUGO, c->dent, (u32 *)&c->rate); - if (IS_ERR(d)) { - err = PTR_ERR(d); + if (!d) { + err = -ENOMEM; goto err_out; } d = debugfs_create_x32("flags", S_IRUGO, c->dent, (u32 *)&c->flags); - if (IS_ERR(d)) { - err = PTR_ERR(d); + if (!d) { + err = -ENOMEM; goto err_out; } return 0; @@ -483,8 +483,8 @@ static int __init clk_debugfs_init(void) int err; d = debugfs_create_dir("clock", NULL); - if (IS_ERR(d)) - return PTR_ERR(d); + if (!d) + return -ENOMEM; clk_debugfs_root = d; list_for_each_entry(c, &clocks, node) { diff --git a/arch/arm/plat-omap/include/mach/entry-macro.S b/arch/arm/plat-omap/include/mach/entry-macro.S index 030118ee204..2276f89671d 100644 --- a/arch/arm/plat-omap/include/mach/entry-macro.S +++ b/arch/arm/plat-omap/include/mach/entry-macro.S @@ -65,7 +65,8 @@ #include <mach/omap34xx.h> #endif -#define INTCPS_SIR_IRQ_OFFSET 0x0040 /* Active interrupt number */ +#define INTCPS_SIR_IRQ_OFFSET 0x0040 /* Active interrupt offset */ +#define ACTIVEIRQ_MASK 0x7f /* Active interrupt bits */ .macro disable_fiq .endm @@ -88,6 +89,7 @@ cmp \irqnr, #0x0 2222: ldrne \irqnr, [\base, #INTCPS_SIR_IRQ_OFFSET] + and \irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */ .endm diff --git a/arch/arm/plat-omap/include/mach/irqs.h b/arch/arm/plat-omap/include/mach/irqs.h index a2929ac8c68..bed5274c910 100644 --- a/arch/arm/plat-omap/include/mach/irqs.h +++ b/arch/arm/plat-omap/include/mach/irqs.h @@ -372,7 +372,7 @@ /* External TWL4030 gpio interrupts are optional */ #define TWL4030_GPIO_IRQ_BASE TWL4030_PWR_IRQ_END -#ifdef CONFIG_TWL4030_GPIO +#ifdef CONFIG_GPIO_TWL4030 #define TWL4030_GPIO_NR_IRQS 18 #else #define TWL4030_GPIO_NR_IRQS 0 diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig index d7a6e487f21..e80a32822d8 100644 --- a/arch/arm/plat-s3c/Kconfig +++ b/arch/arm/plat-s3c/Kconfig @@ -166,3 +166,9 @@ config S3C_DEV_I2C1 depends on PLAT_S3C help Compile in platform device definitions for I2C channel 1 + +config S3C_DEV_FB + bool + depends on PLAT_S3C + help + Compile in platform device definition for framebuffer diff --git a/arch/arm/plat-s3c/Makefile b/arch/arm/plat-s3c/Makefile index 3fcee0c44e1..39195f972d5 100644 --- a/arch/arm/plat-s3c/Makefile +++ b/arch/arm/plat-s3c/Makefile @@ -24,3 +24,4 @@ obj-$(CONFIG_S3C_DEV_HSMMC) += dev-hsmmc.o obj-$(CONFIG_S3C_DEV_HSMMC1) += dev-hsmmc1.o obj-y += dev-i2c0.o obj-$(CONFIG_S3C_DEV_I2C1) += dev-i2c1.o +obj-$(CONFIG_S3C_DEV_FB) += dev-fb.o diff --git a/arch/arm/plat-s3c/dev-fb.c b/arch/arm/plat-s3c/dev-fb.c new file mode 100644 index 00000000000..0454b8ec02e --- /dev/null +++ b/arch/arm/plat-s3c/dev-fb.c @@ -0,0 +1,72 @@ +/* linux/arch/arm/plat-s3c/dev-fb.c + * + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * S3C series device definition for framebuffer device + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/platform_device.h> +#include <linux/fb.h> + +#include <mach/map.h> +#include <mach/regs-fb.h> + +#include <plat/fb.h> +#include <plat/devs.h> +#include <plat/cpu.h> + +static struct resource s3c_fb_resource[] = { + [0] = { + .start = S3C_PA_FB, + .end = S3C_PA_FB + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_LCD_VSYNC, + .end = IRQ_LCD_VSYNC, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .start = IRQ_LCD_FIFO, + .end = IRQ_LCD_FIFO, + .flags = IORESOURCE_IRQ, + }, + [3] = { + .start = IRQ_LCD_SYSTEM, + .end = IRQ_LCD_SYSTEM, + .flags = IORESOURCE_IRQ, + }, +}; + +struct platform_device s3c_device_fb = { + .name = "s3c-fb", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_fb_resource), + .resource = s3c_fb_resource, + .dev.dma_mask = &s3c_device_fb.dev.coherent_dma_mask, + .dev.coherent_dma_mask = 0xffffffffUL, +}; + +void __init s3c_fb_set_platdata(struct s3c_fb_platdata *pd) +{ + struct s3c_fb_platdata *npd; + + if (!pd) { + printk(KERN_ERR "%s: no platform data\n", __func__); + return; + } + + npd = kmemdup(pd, sizeof(struct s3c_fb_platdata), GFP_KERNEL); + if (!npd) + printk(KERN_ERR "%s: no memory for platform data\n", __func__); + + s3c_device_fb.dev.platform_data = npd; +} diff --git a/arch/arm/plat-s3c/include/plat/devs.h b/arch/arm/plat-s3c/include/plat/devs.h index 0e342d1fafb..6b1b5231511 100644 --- a/arch/arm/plat-s3c/include/plat/devs.h +++ b/arch/arm/plat-s3c/include/plat/devs.h @@ -24,6 +24,7 @@ extern struct platform_device *s3c24xx_uart_src[]; extern struct platform_device s3c_device_timer[]; +extern struct platform_device s3c_device_fb; extern struct platform_device s3c_device_usb; extern struct platform_device s3c_device_lcd; extern struct platform_device s3c_device_wdt; diff --git a/arch/arm/plat-s3c/include/plat/fb.h b/arch/arm/plat-s3c/include/plat/fb.h new file mode 100644 index 00000000000..214ff561b0d --- /dev/null +++ b/arch/arm/plat-s3c/include/plat/fb.h @@ -0,0 +1,73 @@ +/* linux/arch/arm/plat-s3c/include/plat/fb.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C - FB platform data definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_S3C_FB_H +#define __PLAT_S3C_FB_H __FILE__ + +/** + * struct s3c_fb_pd_win - per window setup data + * @win_mode: The display parameters to initialise (not for window 0) + * @virtual_x: The virtual X size. + * @virtual_y: The virtual Y size. + */ +struct s3c_fb_pd_win { + struct fb_videomode win_mode; + + unsigned short default_bpp; + unsigned short max_bpp; + unsigned short virtual_x; + unsigned short virtual_y; +}; + +/** + * struct s3c_fb_platdata - S3C driver platform specific information + * @setup_gpio: Setup the external GPIO pins to the right state to transfer + * the data from the display system to the connected display + * device. + * @vidcon0: The base vidcon0 values to control the panel data format. + * @vidcon1: The base vidcon1 values to control the panel data output. + * @win: The setup data for each hardware window, or NULL for unused. + * @display_mode: The LCD output display mode. + * + * The platform data supplies the video driver with all the information + * it requires to work with the display(s) attached to the machine. It + * controls the initial mode, the number of display windows (0 is always + * the base framebuffer) that are initialised etc. + * + */ +struct s3c_fb_platdata { + void (*setup_gpio)(void); + + struct s3c_fb_pd_win *win[S3C_FB_MAX_WIN]; + + u32 vidcon0; + u32 vidcon1; +}; + +/** + * s3c_fb_set_platdata() - Setup the FB device with platform data. + * @pd: The platform data to set. The data is copied from the passed structure + * so the machine data can mark the data __initdata so that any unused + * machines will end up dumping their data at runtime. + */ +extern void s3c_fb_set_platdata(struct s3c_fb_platdata *pd); + +/** + * s3c64xx_fb_gpio_setup_24bpp() - S3C64XX setup function for 24bpp LCD + * + * Initialise the GPIO for an 24bpp LCD display on the RGB interface. + */ +extern void s3c64xx_fb_gpio_setup_24bpp(void); + +#endif /* __PLAT_S3C_FB_H */ diff --git a/arch/arm/plat-s3c/include/plat/regs-fb.h b/arch/arm/plat-s3c/include/plat/regs-fb.h new file mode 100644 index 00000000000..e9ee599d430 --- /dev/null +++ b/arch/arm/plat-s3c/include/plat/regs-fb.h @@ -0,0 +1,366 @@ +/* arch/arm/plat-s3c/include/plat/regs-fb.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C Platform - new-style framebuffer register definitions + * + * This is the register set for the new style framebuffer interface + * found from the S3C2443 onwards into the S3C2416, S3C2450 and the + * S3C64XX series such as the S3C6400 and S3C6410. + * + * The file does not contain the cpu specific items which are based on + * whichever architecture is selected, it only contains the core of the + * register set. See <mach/regs-fb.h> to get the specifics. + * + * Note, we changed to using regs-fb.h as it avoids any clashes with + * the original regs-lcd.h so out of the way of regs-lcd.h as well as + * indicating the newer block is much more than just an LCD interface. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* Please do not include this file directly, use <mach/regs-fb.h> to + * ensure all the localised SoC support is included as necessary. +*/ + +/* VIDCON0 */ + +#define VIDCON0 (0x00) +#define VIDCON0_INTERLACE (1 << 29) +#define VIDCON0_VIDOUT_MASK (0x3 << 26) +#define VIDCON0_VIDOUT_SHIFT (26) +#define VIDCON0_VIDOUT_RGB (0x0 << 26) +#define VIDCON0_VIDOUT_TV (0x1 << 26) +#define VIDCON0_VIDOUT_I80_LDI0 (0x2 << 26) +#define VIDCON0_VIDOUT_I80_LDI1 (0x3 << 26) + +#define VIDCON0_L1_DATA_MASK (0x7 << 23) +#define VIDCON0_L1_DATA_SHIFT (23) +#define VIDCON0_L1_DATA_16BPP (0x0 << 23) +#define VIDCON0_L1_DATA_18BPP16 (0x1 << 23) +#define VIDCON0_L1_DATA_18BPP9 (0x2 << 23) +#define VIDCON0_L1_DATA_24BPP (0x3 << 23) +#define VIDCON0_L1_DATA_18BPP (0x4 << 23) +#define VIDCON0_L1_DATA_16BPP8 (0x5 << 23) + +#define VIDCON0_L0_DATA_MASK (0x7 << 20) +#define VIDCON0_L0_DATA_SHIFT (20) +#define VIDCON0_L0_DATA_16BPP (0x0 << 20) +#define VIDCON0_L0_DATA_18BPP16 (0x1 << 20) +#define VIDCON0_L0_DATA_18BPP9 (0x2 << 20) +#define VIDCON0_L0_DATA_24BPP (0x3 << 20) +#define VIDCON0_L0_DATA_18BPP (0x4 << 20) +#define VIDCON0_L0_DATA_16BPP8 (0x5 << 20) + +#define VIDCON0_PNRMODE_MASK (0x3 << 17) +#define VIDCON0_PNRMODE_SHIFT (17) +#define VIDCON0_PNRMODE_RGB (0x0 << 17) +#define VIDCON0_PNRMODE_BGR (0x1 << 17) +#define VIDCON0_PNRMODE_SERIAL_RGB (0x2 << 17) +#define VIDCON0_PNRMODE_SERIAL_BGR (0x3 << 17) + +#define VIDCON0_CLKVALUP (1 << 16) +#define VIDCON0_CLKVAL_F_MASK (0xff << 6) +#define VIDCON0_CLKVAL_F_SHIFT (6) +#define VIDCON0_CLKVAL_F_LIMIT (0xff) +#define VIDCON0_CLKVAL_F(_x) ((_x) << 6) +#define VIDCON0_VLCKFREE (1 << 5) +#define VIDCON0_CLKDIR (1 << 4) + +#define VIDCON0_CLKSEL_MASK (0x3 << 2) +#define VIDCON0_CLKSEL_SHIFT (2) +#define VIDCON0_CLKSEL_HCLK (0x0 << 2) +#define VIDCON0_CLKSEL_LCD (0x1 << 2) +#define VIDCON0_CLKSEL_27M (0x3 << 2) + +#define VIDCON0_ENVID (1 << 1) +#define VIDCON0_ENVID_F (1 << 0) + +#define VIDCON1 (0x04) +#define VIDCON1_LINECNT_MASK (0x7ff << 16) +#define VIDCON1_LINECNT_SHIFT (16) +#define VIDCON1_LINECNT_GET(_v) (((_v) >> 16) & 0x7ff) +#define VIDCON1_VSTATUS_MASK (0x3 << 13) +#define VIDCON1_VSTATUS_SHIFT (13) +#define VIDCON1_VSTATUS_VSYNC (0x0 << 13) +#define VIDCON1_VSTATUS_BACKPORCH (0x1 << 13) +#define VIDCON1_VSTATUS_ACTIVE (0x2 << 13) +#define VIDCON1_VSTATUS_FRONTPORCH (0x0 << 13) + +#define VIDCON1_INV_VCLK (1 << 7) +#define VIDCON1_INV_HSYNC (1 << 6) +#define VIDCON1_INV_VSYNC (1 << 5) +#define VIDCON1_INV_VDEN (1 << 4) + +/* VIDCON2 */ + +#define VIDCON2 (0x08) +#define VIDCON2_EN601 (1 << 23) +#define VIDCON2_TVFMTSEL_SW (1 << 14) + +#define VIDCON2_TVFMTSEL1_MASK (0x3 << 12) +#define VIDCON2_TVFMTSEL1_SHIFT (12) +#define VIDCON2_TVFMTSEL1_RGB (0x0 << 12) +#define VIDCON2_TVFMTSEL1_YUV422 (0x1 << 12) +#define VIDCON2_TVFMTSEL1_YUV444 (0x2 << 12) + +#define VIDCON2_ORGYCbCr (1 << 8) +#define VIDCON2_YUVORDCrCb (1 << 7) + +/* VIDTCON0 */ + +#define VIDTCON0_VBPDE_MASK (0xff << 24) +#define VIDTCON0_VBPDE_SHIFT (24) +#define VIDTCON0_VBPDE_LIMIT (0xff) +#define VIDTCON0_VBPDE(_x) ((_x) << 24) + +#define VIDTCON0_VBPD_MASK (0xff << 16) +#define VIDTCON0_VBPD_SHIFT (16) +#define VIDTCON0_VBPD_LIMIT (0xff) +#define VIDTCON0_VBPD(_x) ((_x) << 16) + +#define VIDTCON0_VFPD_MASK (0xff << 8) +#define VIDTCON0_VFPD_SHIFT (8) +#define VIDTCON0_VFPD_LIMIT (0xff) +#define VIDTCON0_VFPD(_x) ((_x) << 8) + +#define VIDTCON0_VSPW_MASK (0xff << 0) +#define VIDTCON0_VSPW_SHIFT (0) +#define VIDTCON0_VSPW_LIMIT (0xff) +#define VIDTCON0_VSPW(_x) ((_x) << 0) + +/* VIDTCON1 */ + +#define VIDTCON1_VFPDE_MASK (0xff << 24) +#define VIDTCON1_VFPDE_SHIFT (24) +#define VIDTCON1_VFPDE_LIMIT (0xff) +#define VIDTCON1_VFPDE(_x) ((_x) << 24) + +#define VIDTCON1_HBPD_MASK (0xff << 16) +#define VIDTCON1_HBPD_SHIFT (16) +#define VIDTCON1_HBPD_LIMIT (0xff) +#define VIDTCON1_HBPD(_x) ((_x) << 16) + +#define VIDTCON1_HFPD_MASK (0xff << 8) +#define VIDTCON1_HFPD_SHIFT (8) +#define VIDTCON1_HFPD_LIMIT (0xff) +#define VIDTCON1_HFPD(_x) ((_x) << 8) + +#define VIDTCON1_HSPW_MASK (0xff << 0) +#define VIDTCON1_HSPW_SHIFT (0) +#define VIDTCON1_HSPW_LIMIT (0xff) +#define VIDTCON1_HSPW(_x) ((_x) << 0) + +#define VIDTCON2 (0x18) +#define VIDTCON2_LINEVAL_MASK (0x7ff << 11) +#define VIDTCON2_LINEVAL_SHIFT (11) +#define VIDTCON2_LINEVAL_LIMIT (0x7ff) +#define VIDTCON2_LINEVAL(_x) ((_x) << 11) + +#define VIDTCON2_HOZVAL_MASK (0x7ff << 0) +#define VIDTCON2_HOZVAL_SHIFT (0) +#define VIDTCON2_HOZVAL_LIMIT (0x7ff) +#define VIDTCON2_HOZVAL(_x) ((_x) << 0) + +/* WINCONx */ + + +#define WINCONx_BITSWP (1 << 18) +#define WINCONx_BYTSWP (1 << 17) +#define WINCONx_HAWSWP (1 << 16) +#define WINCONx_BURSTLEN_MASK (0x3 << 9) +#define WINCONx_BURSTLEN_SHIFT (9) +#define WINCONx_BURSTLEN_16WORD (0x0 << 9) +#define WINCONx_BURSTLEN_8WORD (0x1 << 9) +#define WINCONx_BURSTLEN_4WORD (0x2 << 9) + +#define WINCONx_ENWIN (1 << 0) +#define WINCON0_BPPMODE_MASK (0xf << 2) +#define WINCON0_BPPMODE_SHIFT (2) +#define WINCON0_BPPMODE_1BPP (0x0 << 2) +#define WINCON0_BPPMODE_2BPP (0x1 << 2) +#define WINCON0_BPPMODE_4BPP (0x2 << 2) +#define WINCON0_BPPMODE_8BPP_PALETTE (0x3 << 2) +#define WINCON0_BPPMODE_16BPP_565 (0x5 << 2) +#define WINCON0_BPPMODE_16BPP_1555 (0x7 << 2) +#define WINCON0_BPPMODE_18BPP_666 (0x8 << 2) +#define WINCON0_BPPMODE_24BPP_888 (0xb << 2) + +#define WINCON1_BLD_PIX (1 << 6) + +#define WINCON1_ALPHA_SEL (1 << 1) +#define WINCON1_BPPMODE_MASK (0xf << 2) +#define WINCON1_BPPMODE_SHIFT (2) +#define WINCON1_BPPMODE_1BPP (0x0 << 2) +#define WINCON1_BPPMODE_2BPP (0x1 << 2) +#define WINCON1_BPPMODE_4BPP (0x2 << 2) +#define WINCON1_BPPMODE_8BPP_PALETTE (0x3 << 2) +#define WINCON1_BPPMODE_8BPP_1232 (0x4 << 2) +#define WINCON1_BPPMODE_16BPP_565 (0x5 << 2) +#define WINCON1_BPPMODE_16BPP_A1555 (0x6 << 2) +#define WINCON1_BPPMODE_16BPP_I1555 (0x7 << 2) +#define WINCON1_BPPMODE_18BPP_666 (0x8 << 2) +#define WINCON1_BPPMODE_18BPP_A1665 (0x9 << 2) +#define WINCON1_BPPMODE_19BPP_A1666 (0xa << 2) +#define WINCON1_BPPMODE_24BPP_888 (0xb << 2) +#define WINCON1_BPPMODE_24BPP_A1887 (0xc << 2) +#define WINCON1_BPPMODE_25BPP_A1888 (0xd << 2) +#define WINCON1_BPPMODE_28BPP_A4888 (0xd << 2) + + +#define VIDOSDxA_TOPLEFT_X_MASK (0x7ff << 11) +#define VIDOSDxA_TOPLEFT_X_SHIFT (11) +#define VIDOSDxA_TOPLEFT_X_LIMIT (0x7ff) +#define VIDOSDxA_TOPLEFT_X(_x) ((_x) << 11) + +#define VIDOSDxA_TOPLEFT_Y_MASK (0x7ff << 0) +#define VIDOSDxA_TOPLEFT_Y_SHIFT (0) +#define VIDOSDxA_TOPLEFT_Y_LIMIT (0x7ff) +#define VIDOSDxA_TOPLEFT_Y(_x) ((_x) << 0) + +#define VIDOSDxB_BOTRIGHT_X_MASK (0x7ff << 11) +#define VIDOSDxB_BOTRIGHT_X_SHIFT (11) +#define VIDOSDxB_BOTRIGHT_X_LIMIT (0x7ff) +#define VIDOSDxB_BOTRIGHT_X(_x) ((_x) << 11) + +#define VIDOSDxB_BOTRIGHT_Y_MASK (0x7ff << 0) +#define VIDOSDxB_BOTRIGHT_Y_SHIFT (0) +#define VIDOSDxB_BOTRIGHT_Y_LIMIT (0x7ff) +#define VIDOSDxB_BOTRIGHT_Y(_x) ((_x) << 0) + +/* For VIDOSD[1..4]C */ +#define VIDISD14C_ALPHA0_R(_x) ((_x) << 20) +#define VIDISD14C_ALPHA0_G_MASK (0xf << 16) +#define VIDISD14C_ALPHA0_G_SHIFT (16) +#define VIDISD14C_ALPHA0_G_LIMIT (0xf) +#define VIDISD14C_ALPHA0_G(_x) ((_x) << 16) +#define VIDISD14C_ALPHA0_B_MASK (0xf << 12) +#define VIDISD14C_ALPHA0_B_SHIFT (12) +#define VIDISD14C_ALPHA0_B_LIMIT (0xf) +#define VIDISD14C_ALPHA0_B(_x) ((_x) << 12) +#define VIDISD14C_ALPHA1_R_MASK (0xf << 8) +#define VIDISD14C_ALPHA1_R_SHIFT (8) +#define VIDISD14C_ALPHA1_R_LIMIT (0xf) +#define VIDISD14C_ALPHA1_R(_x) ((_x) << 8) +#define VIDISD14C_ALPHA1_G_MASK (0xf << 4) +#define VIDISD14C_ALPHA1_G_SHIFT (4) +#define VIDISD14C_ALPHA1_G_LIMIT (0xf) +#define VIDISD14C_ALPHA1_G(_x) ((_x) << 4) +#define VIDISD14C_ALPHA1_B_MASK (0xf << 0) +#define VIDISD14C_ALPHA1_B_SHIFT (0) +#define VIDISD14C_ALPHA1_B_LIMIT (0xf) +#define VIDISD14C_ALPHA1_B(_x) ((_x) << 0) + +/* Video buffer addresses */ +#define VIDW_BUF_START(_buff) (0xA0 + ((_buff) * 8)) +#define VIDW_BUF_START1(_buff) (0xA4 + ((_buff) * 8)) +#define VIDW_BUF_END(_buff) (0xD0 + ((_buff) * 8)) +#define VIDW_BUF_END1(_buff) (0xD4 + ((_buff) * 8)) +#define VIDW_BUF_SIZE(_buff) (0x100 + ((_buff) * 4)) + +#define VIDW_BUF_SIZE_OFFSET_MASK (0x1fff << 13) +#define VIDW_BUF_SIZE_OFFSET_SHIFT (13) +#define VIDW_BUF_SIZE_OFFSET_LIMIT (0x1fff) +#define VIDW_BUF_SIZE_OFFSET(_x) ((_x) << 13) + +#define VIDW_BUF_SIZE_PAGEWIDTH_MASK (0x1fff << 0) +#define VIDW_BUF_SIZE_PAGEWIDTH_SHIFT (0) +#define VIDW_BUF_SIZE_PAGEWIDTH_LIMIT (0x1fff) +#define VIDW_BUF_SIZE_PAGEWIDTH(_x) ((_x) << 0) + +/* Interrupt controls and status */ + +#define VIDINTCON0_FIFOINTERVAL_MASK (0x3f << 20) +#define VIDINTCON0_FIFOINTERVAL_SHIFT (20) +#define VIDINTCON0_FIFOINTERVAL_LIMIT (0x3f) +#define VIDINTCON0_FIFOINTERVAL(_x) ((_x) << 20) + +#define VIDINTCON0_INT_SYSMAINCON (1 << 19) +#define VIDINTCON0_INT_SYSSUBCON (1 << 18) +#define VIDINTCON0_INT_I80IFDONE (1 << 17) + +#define VIDINTCON0_FRAMESEL0_MASK (0x3 << 15) +#define VIDINTCON0_FRAMESEL0_SHIFT (15) +#define VIDINTCON0_FRAMESEL0_BACKPORCH (0x0 << 15) +#define VIDINTCON0_FRAMESEL0_VSYNC (0x1 << 15) +#define VIDINTCON0_FRAMESEL0_ACTIVE (0x2 << 15) +#define VIDINTCON0_FRAMESEL0_FRONTPORCH (0x3 << 15) + +#define VIDINTCON0_FRAMESEL1 (1 << 14) +#define VIDINTCON0_FRAMESEL1_NONE (0x0 << 14) +#define VIDINTCON0_FRAMESEL1_BACKPORCH (0x1 << 14) +#define VIDINTCON0_FRAMESEL1_VSYNC (0x2 << 14) +#define VIDINTCON0_FRAMESEL1_FRONTPORCH (0x3 << 14) + +#define VIDINTCON0_INT_FRAME (1 << 12) +#define VIDINTCON0_FIFIOSEL_MASK (0x7f << 5) +#define VIDINTCON0_FIFIOSEL_SHIFT (5) +#define VIDINTCON0_FIFIOSEL_WINDOW0 (0x1 << 5) +#define VIDINTCON0_FIFIOSEL_WINDOW1 (0x2 << 5) + +#define VIDINTCON0_FIFOLEVEL_MASK (0x7 << 2) +#define VIDINTCON0_FIFOLEVEL_SHIFT (2) +#define VIDINTCON0_FIFOLEVEL_TO25PC (0x0 << 2) +#define VIDINTCON0_FIFOLEVEL_TO50PC (0x1 << 2) +#define VIDINTCON0_FIFOLEVEL_TO75PC (0x2 << 2) +#define VIDINTCON0_FIFOLEVEL_EMPTY (0x3 << 2) +#define VIDINTCON0_FIFOLEVEL_FULL (0x4 << 2) + +#define VIDINTCON0_INT_FIFO_MASK (0x3 << 0) +#define VIDINTCON0_INT_FIFO_SHIFT (0) +#define VIDINTCON0_INT_ENABLE (1 << 0) + +#define VIDINTCON1 (0x134) +#define VIDINTCON1_INT_I180 (1 << 2) +#define VIDINTCON1_INT_FRAME (1 << 1) +#define VIDINTCON1_INT_FIFO (1 << 0) + +/* Window colour-key control registers */ + +#define WxKEYCON0_KEYBL_EN (1 << 26) +#define WxKEYCON0_KEYEN_F (1 << 25) +#define WxKEYCON0_DIRCON (1 << 24) +#define WxKEYCON0_COMPKEY_MASK (0xffffff << 0) +#define WxKEYCON0_COMPKEY_SHIFT (0) +#define WxKEYCON0_COMPKEY_LIMIT (0xffffff) +#define WxKEYCON0_COMPKEY(_x) ((_x) << 0) +#define WxKEYCON1_COLVAL_MASK (0xffffff << 0) +#define WxKEYCON1_COLVAL_SHIFT (0) +#define WxKEYCON1_COLVAL_LIMIT (0xffffff) +#define WxKEYCON1_COLVAL(_x) ((_x) << 0) + + +/* Window blanking (MAP) */ + +#define WINxMAP_MAP (1 << 24) +#define WINxMAP_MAP_COLOUR_MASK (0xffffff << 0) +#define WINxMAP_MAP_COLOUR_SHIFT (0) +#define WINxMAP_MAP_COLOUR_LIMIT (0xffffff) +#define WINxMAP_MAP_COLOUR(_x) ((_x) << 0) + +#define WPALCON_PAL_UPDATE (1 << 9) +#define WPALCON_W1PAL_MASK (0x7 << 3) +#define WPALCON_W1PAL_SHIFT (3) +#define WPALCON_W1PAL_25BPP_A888 (0x0 << 3) +#define WPALCON_W1PAL_24BPP (0x1 << 3) +#define WPALCON_W1PAL_19BPP_A666 (0x2 << 3) +#define WPALCON_W1PAL_18BPP_A665 (0x3 << 3) +#define WPALCON_W1PAL_18BPP (0x4 << 3) +#define WPALCON_W1PAL_16BPP_A555 (0x5 << 3) +#define WPALCON_W1PAL_16BPP_565 (0x6 << 3) + +#define WPALCON_W0PAL_MASK (0x7 << 0) +#define WPALCON_W0PAL_SHIFT (0) +#define WPALCON_W0PAL_25BPP_A888 (0x0 << 0) +#define WPALCON_W0PAL_24BPP (0x1 << 0) +#define WPALCON_W0PAL_19BPP_A666 (0x2 << 0) +#define WPALCON_W0PAL_18BPP_A665 (0x3 << 0) +#define WPALCON_W0PAL_18BPP (0x4 << 0) +#define WPALCON_W0PAL_16BPP_A555 (0x5 << 0) +#define WPALCON_W0PAL_16BPP_565 (0x6 << 0) + diff --git a/arch/arm/plat-s3c64xx/Kconfig b/arch/arm/plat-s3c64xx/Kconfig index 9037eb47076..203dd730d1c 100644 --- a/arch/arm/plat-s3c64xx/Kconfig +++ b/arch/arm/plat-s3c64xx/Kconfig @@ -53,4 +53,9 @@ config S3C64XX_SETUP_I2C1 help Common setup code for i2c bus 1. +config S3C64XX_SETUP_FB_24BPP + bool + help + Common setup code for S3C64XX with an 24bpp RGB display helper. + endif diff --git a/arch/arm/plat-s3c64xx/Makefile b/arch/arm/plat-s3c64xx/Makefile index 0a0b8c48a3e..2e6d79bf8f3 100644 --- a/arch/arm/plat-s3c64xx/Makefile +++ b/arch/arm/plat-s3c64xx/Makefile @@ -28,3 +28,4 @@ obj-$(CONFIG_CPU_S3C6400_CLOCK) += s3c6400-clock.o obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0.o obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o +obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o diff --git a/arch/arm/plat-s3c64xx/setup-fb-24bpp.c b/arch/arm/plat-s3c64xx/setup-fb-24bpp.c new file mode 100644 index 00000000000..8e28e448dd2 --- /dev/null +++ b/arch/arm/plat-s3c64xx/setup-fb-24bpp.c @@ -0,0 +1,37 @@ +/* linux/arch/arm/plat-s3c64xx/setup-fb-24bpp.c + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * Base S3C64XX setup information for 24bpp LCD framebuffer + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/fb.h> + +#include <mach/regs-fb.h> +#include <mach/gpio.h> +#include <plat/fb.h> +#include <plat/gpio-cfg.h> + +extern void s3c64xx_fb_gpio_setup_24bpp(void) +{ + unsigned int gpio; + + for (gpio = S3C64XX_GPI(0); gpio <= S3C64XX_GPI(15); gpio++) { + s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); + s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE); + } + + for (gpio = S3C64XX_GPJ(0); gpio <= S3C64XX_GPJ(11); gpio++) { + s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); + s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE); + } +} |