aboutsummaryrefslogtreecommitdiff
path: root/arch/powerpc/boot/dts/mpc832x_mds.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/powerpc/boot/dts/mpc832x_mds.dts')
-rw-r--r--arch/powerpc/boot/dts/mpc832x_mds.dts50
1 files changed, 50 insertions, 0 deletions
diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts
index 5093ef304ff..690252456d3 100644
--- a/arch/powerpc/boot/dts/mpc832x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -7,6 +7,18 @@
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+
+ * To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
+ * this:
+ *
+ * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
+ * 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
+ * next to the serial ports.
+ * 3) Solder a wire from U61-22 to P19K-22.
+ *
+ * Note that there's a typo in the schematic. The board labels the last column
+ * of pins "P19K", but in the schematic, that column is called "P19J". So if
+ * you're going by the schematic, the pin is called "P19J-K22".
*/
/ {
@@ -169,6 +181,23 @@
1 1e 1 0 1 0 /* TX_EN */
1 1f 2 0 1 0>;/* CRS */
};
+ pio5: ucc_pin@05 {
+ pio-map = <
+ /*
+ * open has
+ * port pin dir drain sel irq
+ */
+ 2 0 1 0 2 0 /* TxD5 */
+ 2 8 2 0 2 0 /* RxD5 */
+
+ 2 1d 2 0 0 0 /* CTS5 */
+ 2 1f 1 0 2 0 /* RTS5 */
+
+ 2 18 2 0 0 0 /* CD */
+
+ >;
+ };
+
};
};
@@ -176,6 +205,7 @@
#address-cells = <1>;
#size-cells = <1>;
device_type = "qe";
+ compatible = "fsl,qe";
model = "QE";
ranges = <0 e0100000 00100000>;
reg = <e0100000 480>;
@@ -249,6 +279,26 @@
pio-handle = < &pio4 >;
};
+ ucc@2400 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ model = "UCC";
+ device-id = <5>; /* The UCC number, 1-7*/
+ port-number = <0>; /* Which ttyQEx device */
+ soft-uart; /* We need Soft-UART */
+ reg = <2400 200>;
+ interrupts = <28>; /* From Table 18-12 */
+ interrupt-parent = < &qeic >;
+ /*
+ * For Soft-UART, we need to set TX to 1X, which
+ * means specifying separate clock sources.
+ */
+ rx-clock-name = "brg5";
+ tx-clock-name = "brg6";
+ pio-handle = < &pio5 >;
+ };
+
+
mdio@2320 {
#address-cells = <1>;
#size-cells = <0>;