diff options
Diffstat (limited to 'drivers/ide/ide-tape.c')
| -rw-r--r-- | drivers/ide/ide-tape.c | 1240 |
1 files changed, 192 insertions, 1048 deletions
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c index 5aef63acf1e..bf40d8c824a 100644 --- a/drivers/ide/ide-tape.c +++ b/drivers/ide/ide-tape.c @@ -1,424 +1,18 @@ /* + * IDE ATAPI streaming tape driver. + * * Copyright (C) 1995-1999 Gadi Oxman <gadio@netvision.net.il> * Copyright (C) 2003-2005 Bartlomiej Zolnierkiewicz * - * $Header$ - * * This driver was constructed as a student project in the software laboratory * of the faculty of electrical engineering in the Technion - Israel's * Institute Of Technology, with the guide of Avner Lottem and Dr. Ilana David. * * It is hereby placed under the terms of the GNU general public license. * (See linux/COPYING). - */ - -/* - * IDE ATAPI streaming tape driver. - * - * This driver is a part of the Linux ide driver and works in co-operation - * with linux/drivers/block/ide.c. - * - * The driver, in co-operation with ide.c, basically traverses the - * request-list for the block device interface. The character device - * interface, on the other hand, creates new requests, adds them - * to the request-list of the block device, and waits for their completion. - * - * Pipelined operation mode is now supported on both reads and writes. - * - * The block device major and minor numbers are determined from the - * tape's relative position in the ide interfaces, as explained in ide.c. - * - * The character device interface consists of the following devices: - * - * ht0 major 37, minor 0 first IDE tape, rewind on close. - * ht1 major 37, minor 1 second IDE tape, rewind on close. - * ... - * nht0 major 37, minor 128 first IDE tape, no rewind on close. - * nht1 major 37, minor 129 second IDE tape, no rewind on close. - * ... - * - * Run linux/scripts/MAKEDEV.ide to create the above entries. - * - * The general magnetic tape commands compatible interface, as defined by - * include/linux/mtio.h, is accessible through the character device. - * - * General ide driver configuration options, such as the interrupt-unmask - * flag, can be configured by issuing an ioctl to the block device interface, - * as any other ide device. - * - * Our own ide-tape ioctl's can be issued to either the block device or - * the character device interface. - * - * Maximal throughput with minimal bus load will usually be achieved in the - * following scenario: - * - * 1. ide-tape is operating in the pipelined operation mode. - * 2. No buffering is performed by the user backup program. - * - * Testing was done with a 2 GB CONNER CTMA 4000 IDE ATAPI Streaming Tape Drive. - * - * Ver 0.1 Nov 1 95 Pre-working code :-) - * Ver 0.2 Nov 23 95 A short backup (few megabytes) and restore procedure - * was successful ! (Using tar cvf ... on the block - * device interface). - * A longer backup resulted in major swapping, bad - * overall Linux performance and eventually failed as - * we received non serial read-ahead requests from the - * buffer cache. - * Ver 0.3 Nov 28 95 Long backups are now possible, thanks to the - * character device interface. Linux's responsiveness - * and performance doesn't seem to be much affected - * from the background backup procedure. - * Some general mtio.h magnetic tape operations are - * now supported by our character device. As a result, - * popular tape utilities are starting to work with - * ide tapes :-) - * The following configurations were tested: - * 1. An IDE ATAPI TAPE shares the same interface - * and irq with an IDE ATAPI CDROM. - * 2. An IDE ATAPI TAPE shares the same interface - * and irq with a normal IDE disk. - * Both configurations seemed to work just fine ! - * However, to be on the safe side, it is meanwhile - * recommended to give the IDE TAPE its own interface - * and irq. - * The one thing which needs to be done here is to - * add a "request postpone" feature to ide.c, - * so that we won't have to wait for the tape to finish - * performing a long media access (DSC) request (such - * as a rewind) before we can access the other device - * on the same interface. This effect doesn't disturb - * normal operation most of the time because read/write - * requests are relatively fast, and once we are - * performing one tape r/w request, a lot of requests - * from the other device can be queued and ide.c will - * service all of them after this single tape request. - * Ver 1.0 Dec 11 95 Integrated into Linux 1.3.46 development tree. - * On each read / write request, we now ask the drive - * if we can transfer a constant number of bytes - * (a parameter of the drive) only to its buffers, - * without causing actual media access. If we can't, - * we just wait until we can by polling the DSC bit. - * This ensures that while we are not transferring - * more bytes than the constant referred to above, the - * interrupt latency will not become too high and - * we won't cause an interrupt timeout, as happened - * occasionally in the previous version. - * While polling for DSC, the current request is - * postponed and ide.c is free to handle requests from - * the other device. This is handled transparently to - * ide.c. The hwgroup locking method which was used - * in the previous version was removed. - * Use of new general features which are provided by - * ide.c for use with atapi devices. - * (Programming done by Mark Lord) - * Few potential bug fixes (Again, suggested by Mark) - * Single character device data transfers are now - * not limited in size, as they were before. - * We are asking the tape about its recommended - * transfer unit and send a larger data transfer - * as several transfers of the above size. - * For best results, use an integral number of this - * basic unit (which is shown during driver - * initialization). I will soon add an ioctl to get - * this important parameter. - * Our data transfer buffer is allocated on startup, - * rather than before each data transfer. This should - * ensure that we will indeed have a data buffer. - * Ver 1.1 Dec 14 95 Fixed random problems which occurred when the tape - * shared an interface with another device. - * (poll_for_dsc was a complete mess). - * Removed some old (non-active) code which had - * to do with supporting buffer cache originated - * requests. - * The block device interface can now be opened, so - * that general ide driver features like the unmask - * interrupts flag can be selected with an ioctl. - * This is the only use of the block device interface. - * New fast pipelined operation mode (currently only on - * writes). When using the pipelined mode, the - * throughput can potentially reach the maximum - * tape supported throughput, regardless of the - * user backup program. On my tape drive, it sometimes - * boosted performance by a factor of 2. Pipelined - * mode is enabled by default, but since it has a few - * downfalls as well, you may want to disable it. - * A short explanation of the pipelined operation mode - * is available below. - * Ver 1.2 Jan 1 96 Eliminated pipelined mode race condition. - * Added pipeline read mode. As a result, restores - * are now as fast as backups. - * Optimized shared interface behavior. The new behavior - * typically results in better IDE bus efficiency and - * higher tape throughput. - * Pre-calculation of the expected read/write request - * service time, based on the tape's parameters. In - * the pipelined operation mode, this allows us to - * adjust our polling frequency to a much lower value, - * and thus to dramatically reduce our load on Linux, - * without any decrease in performance. - * Implemented additional mtio.h operations. - * The recommended user block size is returned by - * the MTIOCGET ioctl. - * Additional minor changes. - * Ver 1.3 Feb 9 96 Fixed pipelined read mode bug which prevented the - * use of some block sizes during a restore procedure. - * The character device interface will now present a - * continuous view of the media - any mix of block sizes - * during a backup/restore procedure is supported. The - * driver will buffer the requests internally and - * convert them to the tape's recommended transfer - * unit, making performance almost independent of the - * chosen user block size. - * Some improvements in error recovery. - * By cooperating with ide-dma.c, bus mastering DMA can - * now sometimes be used with IDE tape drives as well. - * Bus mastering DMA has the potential to dramatically - * reduce the CPU's overhead when accessing the device, - * and can be enabled by using hdparm -d1 on the tape's - * block device interface. For more info, read the - * comments in ide-dma.c. - * Ver 1.4 Mar 13 96 Fixed serialize support. - * Ver 1.5 Apr 12 96 Fixed shared interface operation, broken in 1.3.85. - * Fixed pipelined read mode inefficiency. - * Fixed nasty null dereferencing bug. - * Ver 1.6 Aug 16 96 Fixed FPU usage in the driver. - * Fixed end of media bug. - * Ver 1.7 Sep 10 96 Minor changes for the CONNER CTT8000-A model. - * Ver 1.8 Sep 26 96 Attempt to find a better balance between good - * interactive response and high system throughput. - * Ver 1.9 Nov 5 96 Automatically cross encountered filemarks rather - * than requiring an explicit FSF command. - * Abort pending requests at end of media. - * MTTELL was sometimes returning incorrect results. - * Return the real block size in the MTIOCGET ioctl. - * Some error recovery bug fixes. - * Ver 1.10 Nov 5 96 Major reorganization. - * Reduced CPU overhead a bit by eliminating internal - * bounce buffers. - * Added module support. - * Added multiple tape drives support. - * Added partition support. - * Rewrote DSC handling. - * Some portability fixes. - * Removed ide-tape.h. - * Additional minor changes. - * Ver 1.11 Dec 2 96 Bug fix in previous DSC timeout handling. - * Use ide_stall_queue() for DSC overlap. - * Use the maximum speed rather than the current speed - * to compute the request service time. - * Ver 1.12 Dec 7 97 Fix random memory overwriting and/or last block data - * corruption, which could occur if the total number - * of bytes written to the tape was not an integral - * number of tape blocks. - * Add support for INTERRUPT DRQ devices. - * Ver 1.13 Jan 2 98 Add "speed == 0" work-around for HP COLORADO 5GB - * Ver 1.14 Dec 30 98 Partial fixes for the Sony/AIWA tape drives. - * Replace cli()/sti() with hwgroup spinlocks. - * Ver 1.15 Mar 25 99 Fix SMP race condition by replacing hwgroup - * spinlock with private per-tape spinlock. - * Ver 1.16 Sep 1 99 Add OnStream tape support. - * Abort read pipeline on EOD. - * Wait for the tape to become ready in case it returns - * "in the process of becoming ready" on open(). - * Fix zero padding of the last written block in - * case the tape block size is larger than PAGE_SIZE. - * Decrease the default disconnection time to tn. - * Ver 1.16e Oct 3 99 Minor fixes. - * Ver 1.16e1 Oct 13 99 Patches by Arnold Niessen, - * niessen@iae.nl / arnold.niessen@philips.com - * GO-1) Undefined code in idetape_read_position - * according to Gadi's email - * AJN-1) Minor fix asc == 11 should be asc == 0x11 - * in idetape_issue_packet_command (did effect - * debugging output only) - * AJN-2) Added more debugging output, and - * added ide-tape: where missing. I would also - * like to add tape->name where possible - * AJN-3) Added different debug_level's - * via /proc/ide/hdc/settings - * "debug_level" determines amount of debugging output; - * can be changed using /proc/ide/hdx/settings - * 0 : almost no debugging output - * 1 : 0+output errors only - * 2 : 1+output all sensekey/asc - * 3 : 2+follow all chrdev related procedures - * 4 : 3+follow all procedures - * 5 : 4+include pc_stack rq_stack info - * 6 : 5+USE_COUNT updates - * AJN-4) Fixed timeout for retension in idetape_queue_pc_tail - * from 5 to 10 minutes - * AJN-5) Changed maximum number of blocks to skip when - * reading tapes with multiple consecutive write - * errors from 100 to 1000 in idetape_get_logical_blk - * Proposed changes to code: - * 1) output "logical_blk_num" via /proc - * 2) output "current_operation" via /proc - * 3) Either solve or document the fact that `mt rewind' is - * required after reading from /dev/nhtx to be - * able to rmmod the idetape module; - * Also, sometimes an application finishes but the - * device remains `busy' for some time. Same cause ? - * Proposed changes to release-notes: - * 4) write a simple `quickstart' section in the - * release notes; I volunteer if you don't want to - * 5) include a pointer to video4linux in the doc - * to stimulate video applications - * 6) release notes lines 331 and 362: explain what happens - * if the application data rate is higher than 1100 KB/s; - * similar approach to lower-than-500 kB/s ? - * 7) 6.6 Comparison; wouldn't it be better to allow different - * strategies for read and write ? - * Wouldn't it be better to control the tape buffer - * contents instead of the bandwidth ? - * 8) line 536: replace will by would (if I understand - * this section correctly, a hypothetical and unwanted situation - * is being described) - * Ver 1.16f Dec 15 99 Change place of the secondary OnStream header frames. - * Ver 1.17 Nov 2000 / Jan 2001 Marcel Mol, marcel@mesa.nl - * - Add idetape_onstream_mode_sense_tape_parameter_page - * function to get tape capacity in frames: tape->capacity. - * - Add support for DI-50 drives( or any DI- drive). - * - 'workaround' for read error/blank block around block 3000. - * - Implement Early warning for end of media for Onstream. - * - Cosmetic code changes for readability. - * - Idetape_position_tape should not use SKIP bit during - * Onstream read recovery. - * - Add capacity, logical_blk_num and first/last_frame_position - * to /proc/ide/hd?/settings. - * - Module use count was gone in the Linux 2.4 driver. - * Ver 1.17a Apr 2001 Willem Riede osst@riede.org - * - Get drive's actual block size from mode sense block descriptor - * - Limit size of pipeline - * Ver 1.17b Oct 2002 Alan Stern <stern@rowland.harvard.edu> - * Changed IDETAPE_MIN_PIPELINE_STAGES to 1 and actually used - * it in the code! - * Actually removed aborted stages in idetape_abort_pipeline - * instead of just changing the command code. - * Made the transfer byte count for Request Sense equal to the - * actual length of the data transfer. - * Changed handling of partial data transfers: they do not - * cause DMA errors. - * Moved initiation of DMA transfers to the correct place. - * Removed reference to unallocated memory. - * Made __idetape_discard_read_pipeline return the number of - * sectors skipped, not the number of stages. - * Replaced errant kfree() calls with __idetape_kfree_stage(). - * Fixed off-by-one error in testing the pipeline length. - * Fixed handling of filemarks in the read pipeline. - * Small code optimization for MTBSF and MTBSFM ioctls. - * Don't try to unlock the door during device close if is - * already unlocked! - * Cosmetic fixes to miscellaneous debugging output messages. - * Set the minimum /proc/ide/hd?/settings values for "pipeline", - * "pipeline_min", and "pipeline_max" to 1. - * - * Here are some words from the first releases of hd.c, which are quoted - * in ide.c and apply here as well: - * - * | Special care is recommended. Have Fun! * - */ - -/* - * An overview of the pipelined operation mode. - * - * In the pipelined write mode, we will usually just add requests to our - * pipeline and return immediately, before we even start to service them. The - * user program will then have enough time to prepare the next request while - * we are still busy servicing previous requests. In the pipelined read mode, - * the situation is similar - we add read-ahead requests into the pipeline, - * before the user even requested them. - * - * The pipeline can be viewed as a "safety net" which will be activated when - * the system load is high and prevents the user backup program from keeping up - * with the current tape speed. At this point, the pipeline will get - * shorter and shorter but the tape will still be streaming at the same speed. - * Assuming we have enough pipeline stages, the system load will hopefully - * decrease before the pipeline is completely empty, and the backup program - * will be able to "catch up" and refill the pipeline again. - * - * When using the pipelined mode, it would be best to disable any type of - * buffering done by the user program, as ide-tape already provides all the - * benefits in the kernel, where it can be done in a more efficient way. - * As we will usually not block the user program on a request, the most - * efficient user code will then be a simple read-write-read-... cycle. - * Any additional logic will usually just slow down the backup process. - * - * Using the pipelined mode, I get a constant over 400 KBps throughput, - * which seems to be the maximum throughput supported by my tape. - * - * However, there are some downfalls: - * - * 1. We use memory (for data buffers) in proportional to the number - * of pipeline stages (each stage is about 26 KB with my tape). - * 2. In the pipelined write mode, we cheat and postpone error codes - * to the user task. In read mode, the actual tape position - * will be a bit further than the last requested block. - * - * Concerning (1): - * - * 1. We allocate stages dynamically only when we need them. When - * we don't need them, we don't consume additional memory. In - * case we can't allocate stages, we just manage without them - * (at the expense of decreased throughput) so when Linux is - * tight in memory, we will not pose additional difficulties. - * - * 2. The maximum number of stages (which is, in fact, the maximum - * amount of memory) which we allocate is limited by the compile - * time parameter IDETAPE_MAX_PIPELINE_STAGES. - * - * 3. The maximum number of stages is a controlled parameter - We - * don't start from the user defined maximum number of stages - * but from the lower IDETAPE_MIN_PIPELINE_STAGES (again, we - * will not even allocate this amount of stages if the user - * program can't handle the speed). We then implement a feedback - * loop which checks if the pipeline is empty, and if it is, we - * increase the maximum number of stages as necessary until we - * reach the optimum value which just manages to keep the tape - * busy with minimum allocated memory or until we reach - * IDETAPE_MAX_PIPELINE_STAGES. - * - * Concerning (2): - * - * In pipelined write mode, ide-tape can not return accurate error codes - * to the user program since we usually just add the request to the - * pipeline without waiting for it to be serviced. In case an error - * occurs, I will report it on the next user request. - * - * In the pipelined read mode, subsequent read requests or forward - * filemark spacing will perform correctly, as we preserve all blocks - * and filemarks which we encountered during our excess read-ahead. - * - * For accurate tape positioning and error reporting, disabling - * pipelined mode might be the best option. - * - * You can enable/disable/tune the pipelined operation mode by adjusting - * the compile time parameters below. - */ - -/* - * Possible improvements. - * - * 1. Support for the ATAPI overlap protocol. - * - * In order to maximize bus throughput, we currently use the DSC - * overlap method which enables ide.c to service requests from the - * other device while the tape is busy executing a command. The - * DSC overlap method involves polling the tape's status register - * for the DSC bit, and servicing the other device while the tape - * isn't ready. - * - * In the current QIC development standard (December 1995), - * it is recommended that new tape drives will *in addition* - * implement the ATAPI overlap protocol, which is used for the - * same purpose - efficient use of the IDE bus, but is interrupt - * driven and thus has much less CPU overhead. - * - * ATAPI overlap is likely to be supported in most new ATAPI - * devices, including new ATAPI cdroms, and thus provides us - * a method by which we can achieve higher throughput when - * sharing a (fast) ATA-2 disk with any (slow) new ATAPI device. + * For a historical changelog see + * Documentation/ide/ChangeLog.ide-tape.1995-2002 */ #define IDETAPE_VERSION "1.19" @@ -442,49 +36,13 @@ #include <linux/completion.h> #include <linux/bitops.h> #include <linux/mutex.h> +#include <scsi/scsi.h> #include <asm/byteorder.h> #include <asm/irq.h> #include <asm/uaccess.h> #include <asm/io.h> #include <asm/unaligned.h> - -/* - * partition - */ -typedef struct os_partition_s { - __u8 partition_num; - __u8 par_desc_ver; - __u16 wrt_pass_cntr; - __u32 first_frame_addr; - __u32 last_frame_addr; - __u32 eod_frame_addr; -} os_partition_t; - -/* - * DAT entry - */ -typedef struct os_dat_entry_s { - __u32 blk_sz; - __u16 blk_cnt; - __u8 flags; - __u8 reserved; -} os_dat_entry_t; - -/* - * DAT - */ -#define OS_DAT_FLAGS_DATA (0xc) -#define OS_DAT_FLAGS_MARK (0x1) - -typedef struct os_dat_s { - __u8 dat_sz; - __u8 reserved1; - __u8 entry_cnt; - __u8 reserved3; - os_dat_entry_t dat_list[16]; -} os_dat_t; - #include <linux/mtio.h> /**************************** Tunable parameters *****************************/ @@ -512,10 +70,7 @@ typedef struct os_dat_s { /* * The following are used to debug the driver: * - * Setting IDETAPE_DEBUG_INFO to 1 will report device capabilities. * Setting IDETAPE_DEBUG_LOG to 1 will log driver flow control. - * Setting IDETAPE_DEBUG_BUGS to 1 will enable self-sanity checks in - * some places. * * Setting them to 0 will restore normal operation mode: * @@ -527,9 +82,7 @@ typedef struct os_dat_s { * is verified to be stable enough. This will make it much more * esthetic. */ -#define IDETAPE_DEBUG_INFO 0 #define IDETAPE_DEBUG_LOG 0 -#define IDETAPE_DEBUG_BUGS 1 /* * After each failed packet command we issue a request sense command @@ -671,65 +224,6 @@ typedef struct idetape_packet_command_s { #define PC_WRITING 5 /* - * Capabilities and Mechanical Status Page - */ -typedef struct { - unsigned page_code :6; /* Page code - Should be 0x2a */ - __u8 reserved0_6 :1; - __u8 ps :1; /* parameters saveable */ - __u8 page_length; /* Page Length - Should be 0x12 */ - __u8 reserved2, reserved3; - unsigned ro :1; /* Read Only Mode */ - unsigned reserved4_1234 :4; - unsigned sprev :1; /* Supports SPACE in the reverse direction */ - unsigned reserved4_67 :2; - unsigned reserved5_012 :3; - unsigned efmt :1; /* Supports ERASE command initiated formatting */ - unsigned reserved5_4 :1; - unsigned qfa :1; /* Supports the QFA two partition formats */ - unsigned reserved5_67 :2; - unsigned lock :1; /* Supports locking the volume */ - unsigned locked :1; /* The volume is locked */ - unsigned prevent :1; /* The device defaults in the prevent state after power up */ - unsigned eject :1; /* The device can eject the volume */ - __u8 disconnect :1; /* The device can break request > ctl */ - __u8 reserved6_5 :1; - unsigned ecc :1; /* Supports error correction */ - unsigned cmprs :1; /* Supports data compression */ - unsigned reserved7_0 :1; - unsigned blk512 :1; /* Supports 512 bytes block size */ - unsigned blk1024 :1; /* Supports 1024 bytes block size */ - unsigned reserved7_3_6 :4; - unsigned blk32768 :1; /* slowb - the device restricts the byte count for PIO */ - /* transfers for slow buffer memory ??? */ - /* Also 32768 block size in some cases */ - __u16 max_speed; /* Maximum speed supported in KBps */ - __u8 reserved10, reserved11; - __u16 ctl; /* Continuous Transfer Limit in blocks */ - __u16 speed; /* Current Speed, in KBps */ - __u16 buffer_size; /* Buffer Size, in 512 bytes */ - __u8 reserved18, reserved19; -} idetape_capabilities_page_t; - -/* - * Block Size Page - */ -typedef struct { - unsigned page_code :6; /* Page code - Should be 0x30 */ - unsigned reserved1_6 :1; - unsigned ps :1; - __u8 page_length; /* Page Length - Should be 2 */ - __u8 reserved2; - unsigned play32 :1; - unsigned play32_5 :1; - unsigned reserved2_23 :2; - unsigned record32 :1; - unsigned record32_5 :1; - unsigned reserved2_6 :1; - unsigned one :1; -} idetape_block_size_page_t; - -/* * A pipeline stage. */ typedef struct idetape_stage_s { @@ -739,32 +233,6 @@ typedef struct idetape_stage_s { } idetape_stage_t; /* - * REQUEST SENSE packet command result - Data Format. - */ -typedef struct { - unsigned error_code :7; /* Current of deferred errors */ - unsigned valid :1; /* The information field conforms to QIC-157C */ - __u8 reserved1 :8; /* Segment Number - Reserved */ - unsigned sense_key :4; /* Sense Key */ - unsigned reserved2_4 :1; /* Reserved */ - unsigned ili :1; /* Incorrect Length Indicator */ - unsigned eom :1; /* End Of Medium */ - unsigned filemark :1; /* Filemark */ - __u32 information __attribute__ ((packed)); - __u8 asl; /* Additional sense length (n-7) */ - __u32 command_specific; /* Additional command specific information */ - __u8 asc; /* Additional Sense Code */ - __u8 ascq; /* Additional Sense Code Qualifier */ - __u8 replaceable_unit_code; /* Field Replaceable Unit Code */ - unsigned sk_specific1 :7; /* Sense Key Specific */ - unsigned sksv :1; /* Sense Key Specific information is valid */ - __u8 sk_specific2; /* Sense Key Specific */ - __u8 sk_specific3; /* Sense Key Specific */ - __u8 pad[2]; /* Padding to 20 bytes */ -} idetape_request_sense_result_t; - - -/* * Most of our global data which we need to save even as we leave the * driver due to an interrupt or a timer event is stored in a variable * of type idetape_tape_t, defined below. @@ -854,8 +322,9 @@ typedef struct ide_tape_obj { /* Usually 512 or 1024 bytes */ unsigned short tape_block_size; int user_bs_factor; + /* Copy of the tape's Capabilities and Mechanical Page */ - idetape_capabilities_page_t capabilities; + u8 caps[20]; /* * Active data transfer request parameters. @@ -918,9 +387,6 @@ typedef struct ide_tape_obj { int avg_size; int avg_speed; - /* last sense information */ - idetape_request_sense_result_t sense; - char vendor_id[10]; char product_id[18]; char firmware_revision[6]; @@ -1052,27 +518,6 @@ static void ide_tape_put(struct ide_tape_obj *tape) #define IDETAPE_MEDIUM_PRESENT 9 /* - * Supported ATAPI tape drives packet commands - */ -#define IDETAPE_TEST_UNIT_READY_CMD 0x00 -#define IDETAPE_REWIND_CMD 0x01 -#define IDETAPE_REQUEST_SENSE_CMD 0x03 -#define IDETAPE_READ_CMD 0x08 -#define IDETAPE_WRITE_CMD 0x0a -#define IDETAPE_WRITE_FILEMARK_CMD 0x10 -#define IDETAPE_SPACE_CMD 0x11 -#define IDETAPE_INQUIRY_CMD 0x12 -#define IDETAPE_ERASE_CMD 0x19 -#define IDETAPE_MODE_SENSE_CMD 0x1a -#define IDETAPE_MODE_SELECT_CMD 0x15 -#define IDETAPE_LOAD_UNLOAD_CMD 0x1b -#define IDETAPE_PREVENT_CMD 0x1e -#define IDETAPE_LOCATE_CMD 0x2b -#define IDETAPE_READ_POSITION_CMD 0x34 -#define IDETAPE_READ_BUFFER_CMD 0x3c -#define IDETAPE_SET_SPEED_CMD 0xbb - -/* * Some defines for the READ BUFFER command */ #define IDETAPE_RETRIEVE_FAULTY_BLOCK 6 @@ -1129,31 +574,6 @@ struct idetape_id_gcw { }; /* - * INQUIRY packet command - Data Format (From Table 6-8 of QIC-157C) - */ -typedef struct { - unsigned device_type :5; /* Peripheral Device Type */ - unsigned reserved0_765 :3; /* Peripheral Qualifier - Reserved */ - unsigned reserved1_6t0 :7; /* Reserved */ - unsigned rmb :1; /* Removable Medium Bit */ - unsigned ansi_version :3; /* ANSI Version */ - unsigned ecma_version :3; /* ECMA Version */ - unsigned iso_version :2; /* ISO Version */ - unsigned response_format :4; /* Response Data Format */ - unsigned reserved3_45 :2; /* Reserved */ - unsigned reserved3_6 :1; /* TrmIOP - Reserved */ - unsigned reserved3_7 :1; /* AENC - Reserved */ - __u8 additional_length; /* Additional Length (total_length-4) */ - __u8 rsv5, rsv6, rsv7; /* Reserved */ - __u8 vendor_id[8]; /* Vendor Identification */ - __u8 product_id[16]; /* Product Identification */ - __u8 revision_level[4]; /* Revision Level */ - __u8 vendor_specific[20]; /* Vendor Specific - Optional */ - __u8 reserved56t95[40]; /* Reserved - Optional */ - /* Additional information may be returned */ -} idetape_inquiry_result_t; - -/* * READ POSITION packet command - Data Format (From Table 6-57) */ typedef struct { @@ -1171,100 +591,9 @@ typedef struct { u32 bytes_in_buffer; /* Bytes In Buffer (Optional) */ } idetape_read_position_result_t; -/* - * Follows structures which are related to the SELECT SENSE / MODE SENSE - * packet commands. Those packet commands are still not supported - * by ide-tape. - */ +/* Structures related to the SELECT SENSE / MODE SENSE packet commands. */ #define IDETAPE_BLOCK_DESCRIPTOR 0 #define IDETAPE_CAPABILITIES_PAGE 0x2a -#define IDETAPE_PARAMTR_PAGE 0x2b /* Onstream DI-x0 only */ -#define IDETAPE_BLOCK_SIZE_PAGE 0x30 -#define IDETAPE_BUFFER_FILLING_PAGE 0x33 - -/* - * Mode Parameter Header for the MODE SENSE packet command - */ -typedef struct { - __u8 mode_data_length; /* Length of the following data transfer */ - __u8 medium_type; /* Medium Type */ - __u8 dsp; /* Device Specific Parameter */ - __u8 bdl; /* Block Descriptor Length */ -#if 0 - /* data transfer page */ - __u8 page_code :6; - __u8 reserved0_6 :1; - __u8 ps :1; /* parameters saveable */ - __u8 page_length; /* page Length == 0x02 */ - __u8 reserved2; - __u8 read32k :1; /* 32k blk size (data only) */ - __u8 read32k5 :1; /* 32.5k blk size (data&AUX) */ - __u8 reserved3_23 :2; - __u8 write32k :1; /* 32k blk size (data only) */ - __u8 write32k5 :1; /* 32.5k blk size (data&AUX) */ - __u8 reserved3_6 :1; - __u8 streaming :1; /* streaming mode enable */ -#endif -} idetape_mode_parameter_header_t; - -/* - * Mode Parameter Block Descriptor the MODE SENSE packet command - * - * Support for block descriptors is optional. - */ -typedef struct { - __u8 density_code; /* Medium density code */ - __u8 blocks[3]; /* Number of blocks */ - __u8 reserved4; /* Reserved */ - __u8 length[3]; /* Block Length */ -} idetape_parameter_block_descriptor_t; - -/* - * The Data Compression Page, as returned by the MODE SENSE packet command. - */ -typedef struct { - unsigned page_code :6; /* Page Code - Should be 0xf */ - unsigned reserved0 :1; /* Reserved */ - unsigned ps :1; - __u8 page_length; /* Page Length - Should be 14 */ - unsigned reserved2 :6; /* Reserved */ - unsigned dcc :1; /* Data Compression Capable */ - unsigned dce :1; /* Data Compression Enable */ - unsigned reserved3 :5; /* Reserved */ - unsigned red :2; /* Report Exception on Decompression */ - unsigned dde :1; /* Data Decompression Enable */ - __u32 ca; /* Compression Algorithm */ - __u32 da; /* Decompression Algorithm */ - __u8 reserved[4]; /* Reserved */ -} idetape_data_compression_page_t; - -/* - * The Medium Partition Page, as returned by the MODE SENSE packet command. - */ -typedef struct { - unsigned page_code :6; /* Page Code - Should be 0x11 */ - unsigned reserved1_6 :1; /* Reserved */ - unsigned ps :1; - __u8 page_length; /* Page Length - Should be 6 */ - __u8 map; /* Maximum Additional Partitions - Should be 0 */ - __u8 apd; /* Additional Partitions Defined - Should be 0 */ - unsigned reserved4_012 :3; /* Reserved */ - unsigned psum :2; /* Should be 0 */ - unsigned idp :1; /* Should be 0 */ - unsigned sdp :1; /* Should be 0 */ - unsigned fdp :1; /* Fixed Data Partitions */ - __u8 mfr; /* Medium Format Recognition */ - __u8 reserved[2]; /* Reserved */ -} idetape_medium_partition_page_t; - -/* - * Run time configurable parameters. - */ -typedef struct { - int dsc_rw_frequency; - int dsc_media_access_frequency; - int nr_stages; -} idetape_config_t; /* * The variables below are used for the character device interface. @@ -1309,14 +638,12 @@ static void idetape_input_buffers (ide_drive_t *drive, idetape_pc_t *pc, unsigne int count; while (bcount) { -#if IDETAPE_DEBUG_BUGS if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_input_buffers\n"); idetape_discard_data(drive, bcount); return; } -#endif /* IDETAPE_DEBUG_BUGS */ count = min((unsigned int)(bh->b_size - atomic_read(&bh->b_count)), bcount); HWIF(drive)->atapi_input_bytes(drive, bh->b_data + atomic_read(&bh->b_count), count); bcount -= count; @@ -1336,13 +663,11 @@ static void idetape_output_buffers (ide_drive_t *drive, idetape_pc_t *pc, unsign int count; while (bcount) { -#if IDETAPE_DEBUG_BUGS if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_output_buffers\n"); return; } -#endif /* IDETAPE_DEBUG_BUGS */ count = min((unsigned int)pc->b_count, (unsigned int)bcount); HWIF(drive)->atapi_output_bytes(drive, pc->b_data, count); bcount -= count; @@ -1367,13 +692,11 @@ static void idetape_update_buffers (idetape_pc_t *pc) if (test_bit(PC_WRITING, &pc->flags)) return; while (bcount) { -#if IDETAPE_DEBUG_BUGS if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_update_buffers\n"); return; } -#endif /* IDETAPE_DEBUG_BUGS */ count = min((unsigned int)bh->b_size, (unsigned int)bcount); atomic_set(&bh->b_count, count); if (atomic_read(&bh->b_count) == bh->b_size) @@ -1446,36 +769,34 @@ static void idetape_init_pc (idetape_pc_t *pc) } /* - * idetape_analyze_error is called on each failed packet command retry - * to analyze the request sense. We currently do not utilize this - * information. + * called on each failed packet command retry to analyze the request sense. We + * currently do not utilize this information. */ -static void idetape_analyze_error (ide_drive_t *drive, idetape_request_sense_result_t *result) +static void idetape_analyze_error(ide_drive_t *drive, u8 *sense) { idetape_tape_t *tape = drive->driver_data; idetape_pc_t *pc = tape->failed_pc; - tape->sense = *result; - tape->sense_key = result->sense_key; - tape->asc = result->asc; - tape->ascq = result->ascq; + tape->sense_key = sense[2] & 0xF; + tape->asc = sense[12]; + tape->ascq = sense[13]; #if IDETAPE_DEBUG_LOG /* - * Without debugging, we only log an error if we decided to - * give up retrying. + * Without debugging, we only log an error if we decided to give up + * retrying. */ if (tape->debug_level >= 1) printk(KERN_INFO "ide-tape: pc = %x, sense key = %x, " "asc = %x, ascq = %x\n", - pc->c[0], result->sense_key, - result->asc, result->ascq); + pc->c[0], tape->sense_key, + tape->asc, tape->ascq); #endif /* IDETAPE_DEBUG_LOG */ - /* - * Correct pc->actually_transferred by asking the tape. - */ + /* Correct pc->actually_transferred by asking the tape. */ if (test_bit(PC_DMA_ERROR, &pc->flags)) { - pc->actually_transferred = pc->request_transfer - tape->tape_block_size * ntohl(get_unaligned(&result->information)); + pc->actually_transferred = pc->request_transfer - + tape->tape_block_size * + be32_to_cpu(get_unaligned((u32 *)&sense[3])); idetape_update_buffers(pc); } @@ -1484,29 +805,29 @@ static void idetape_analyze_error (ide_drive_t *drive, idetape_request_sense_res * with sense key=5, asc=0x22, ascq=0, let it slide. Some drives * (i.e. Seagate STT3401A Travan) don't support 0-length read/writes. */ - if ((pc->c[0] == IDETAPE_READ_CMD || pc->c[0] == IDETAPE_WRITE_CMD) - && pc->c[4] == 0 && pc->c[3] == 0 && pc->c[2] == 0) { /* length==0 */ - if (result->sense_key == 5) { + if ((pc->c[0] == READ_6 || pc->c[0] == WRITE_6) + /* length == 0 */ + && pc->c[4] == 0 && pc->c[3] == 0 && pc->c[2] == 0) { + if (tape->sense_key == 5) { /* don't report an error, everything's ok */ pc->error = 0; /* don't retry read/write */ set_bit(PC_ABORT, &pc->flags); } } - if (pc->c[0] == IDETAPE_READ_CMD && result->filemark) { + if (pc->c[0] == READ_6 && (sense[2] & 0x80)) { pc->error = IDETAPE_ERROR_FILEMARK; set_bit(PC_ABORT, &pc->flags); } - if (pc->c[0] == IDETAPE_WRITE_CMD) { - if (result->eom || - (result->sense_key == 0xd && result->asc == 0x0 && - result->ascq == 0x2)) { + if (pc->c[0] == WRITE_6) { + if ((sense[2] & 0x40) || (tape->sense_key == 0xd + && tape->asc == 0x0 && tape->ascq == 0x2)) { pc->error = IDETAPE_ERROR_EOD; set_bit(PC_ABORT, &pc->flags); } } - if (pc->c[0] == IDETAPE_READ_CMD || pc->c[0] == IDETAPE_WRITE_CMD) { - if (result->sense_key == 8) { + if (pc->c[0] == READ_6 || pc->c[0] == WRITE_6) { + if (tape->sense_key == 8) { pc->error = IDETAPE_ERROR_EOD; set_bit(PC_ABORT, &pc->flags); } @@ -1516,10 +837,7 @@ static void idetape_analyze_error (ide_drive_t *drive, idetape_request_sense_res } } -/* - * idetape_active_next_stage will declare the next stage as "active". - */ -static void idetape_active_next_stage (ide_drive_t *drive) +static void idetape_activate_next_stage(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; idetape_stage_t *stage = tape->next_stage; @@ -1529,12 +847,10 @@ static void idetape_active_next_stage (ide_drive_t *drive) if (tape->debug_level >= 4) printk(KERN_INFO "ide-tape: Reached idetape_active_next_stage\n"); #endif /* IDETAPE_DEBUG_LOG */ -#if IDETAPE_DEBUG_BUGS if (stage == NULL) { printk(KERN_ERR "ide-tape: bug: Trying to activate a non existing stage\n"); return; } -#endif /* IDETAPE_DEBUG_BUGS */ rq->rq_disk = tape->disk; rq->buffer = NULL; @@ -1609,28 +925,24 @@ static void idetape_remove_stage_head (ide_drive_t *drive) if (tape->debug_level >= 4) printk(KERN_INFO "ide-tape: Reached idetape_remove_stage_head\n"); #endif /* IDETAPE_DEBUG_LOG */ -#if IDETAPE_DEBUG_BUGS if (tape->first_stage == NULL) { printk(KERN_ERR "ide-tape: bug: tape->first_stage is NULL\n"); - return; + return; } if (tape->active_stage == tape->first_stage) { printk(KERN_ERR "ide-tape: bug: Trying to free our active pipeline stage\n"); return; } -#endif /* IDETAPE_DEBUG_BUGS */ stage = tape->first_stage; tape->first_stage = stage->next; idetape_kfree_stage(tape, stage); tape->nr_stages--; if (tape->first_stage == NULL) { tape->last_stage = NULL; -#if IDETAPE_DEBUG_BUGS if (tape->next_stage != NULL) printk(KERN_ERR "ide-tape: bug: tape->next_stage != NULL\n"); if (tape->nr_stages) printk(KERN_ERR "ide-tape: bug: nr_stages should be 0 now\n"); -#endif /* IDETAPE_DEBUG_BUGS */ } } @@ -1716,7 +1028,7 @@ static int idetape_end_request(ide_drive_t *drive, int uptodate, int nr_sects) } } if (tape->next_stage != NULL) { - idetape_active_next_stage(drive); + idetape_activate_next_stage(drive); /* * Insert the next request into the request queue. @@ -1748,7 +1060,7 @@ static ide_startstop_t idetape_request_sense_callback (ide_drive_t *drive) printk(KERN_INFO "ide-tape: Reached idetape_request_sense_callback\n"); #endif /* IDETAPE_DEBUG_LOG */ if (!tape->pc->error) { - idetape_analyze_error(drive, (idetape_request_sense_result_t *) tape->pc->buffer); + idetape_analyze_error(drive, tape->pc->buffer); idetape_end_request(drive, 1, 0); } else { printk(KERN_ERR "ide-tape: Error in REQUEST SENSE itself - Aborting request!\n"); @@ -1760,7 +1072,7 @@ static ide_startstop_t idetape_request_sense_callback (ide_drive_t *drive) static void idetape_create_request_sense_cmd (idetape_pc_t *pc) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_REQUEST_SENSE_CMD; + pc->c[0] = REQUEST_SENSE; pc->c[4] = 20; pc->request_transfer = 20; pc->callback = &idetape_request_sense_callback; @@ -1913,15 +1225,14 @@ static ide_startstop_t idetape_pc_intr (ide_drive_t *drive) local_irq_enable(); #if SIMULATE_ERRORS - if ((pc->c[0] == IDETAPE_WRITE_CMD || - pc->c[0] == IDETAPE_READ_CMD) && + if ((pc->c[0] == WRITE_6 || pc->c[0] == READ_6) && (++error_sim_count % 100) == 0) { printk(KERN_INFO "ide-tape: %s: simulating error\n", tape->name); stat |= ERR_STAT; } #endif - if ((stat & ERR_STAT) && pc->c[0] == IDETAPE_REQUEST_SENSE_CMD) + if ((stat & ERR_STAT) && pc->c[0] == REQUEST_SENSE) stat &= ~ERR_STAT; if ((stat & ERR_STAT) || test_bit(PC_DMA_ERROR, &pc->flags)) { /* Error detected */ @@ -1930,7 +1241,7 @@ static ide_startstop_t idetape_pc_intr (ide_drive_t *drive) printk(KERN_INFO "ide-tape: %s: I/O error\n", tape->name); #endif /* IDETAPE_DEBUG_LOG */ - if (pc->c[0] == IDETAPE_REQUEST_SENSE_CMD) { + if (pc->c[0] == REQUEST_SENSE) { printk(KERN_ERR "ide-tape: I/O error in request sense command\n"); return ide_do_reset(drive); } @@ -2118,15 +1429,13 @@ static ide_startstop_t idetape_issue_packet_command (ide_drive_t *drive, idetape int dma_ok = 0; u16 bcount; -#if IDETAPE_DEBUG_BUGS - if (tape->pc->c[0] == IDETAPE_REQUEST_SENSE_CMD && - pc->c[0] == IDETAPE_REQUEST_SENSE_CMD) { + if (tape->pc->c[0] == REQUEST_SENSE && + pc->c[0] == REQUEST_SENSE) { printk(KERN_ERR "ide-tape: possible ide-tape.c bug - " "Two request sense in serial were issued\n"); } -#endif /* IDETAPE_DEBUG_BUGS */ - if (tape->failed_pc == NULL && pc->c[0] != IDETAPE_REQUEST_SENSE_CMD) + if (tape->failed_pc == NULL && pc->c[0] != REQUEST_SENSE) tape->failed_pc = pc; /* Set the current packet command */ tape->pc = pc; @@ -2139,7 +1448,7 @@ static ide_startstop_t idetape_issue_packet_command (ide_drive_t *drive, idetape * filemark, or end of the media, for example). */ if (!test_bit(PC_ABORT, &pc->flags)) { - if (!(pc->c[0] == IDETAPE_TEST_UNIT_READY_CMD && + if (!(pc->c[0] == TEST_UNIT_READY && tape->sense_key == 2 && tape->asc == 4 && (tape->ascq == 1 || tape->ascq == 8))) { printk(KERN_ERR "ide-tape: %s: I/O error, " @@ -2181,8 +1490,8 @@ static ide_startstop_t idetape_issue_packet_command (ide_drive_t *drive, idetape if (dma_ok) /* Will begin DMA later */ set_bit(PC_DMA_IN_PROGRESS, &pc->flags); if (test_bit(IDETAPE_DRQ_INTERRUPT, &tape->flags)) { - ide_set_handler(drive, &idetape_transfer_pc, IDETAPE_WAIT_CMD, NULL); - hwif->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG); + ide_execute_command(drive, WIN_PACKETCMD, &idetape_transfer_pc, + IDETAPE_WAIT_CMD, NULL); return ide_started; } else { hwif->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG); @@ -2212,7 +1521,7 @@ static ide_startstop_t idetape_pc_callback (ide_drive_t *drive) static void idetape_create_mode_sense_cmd (idetape_pc_t *pc, u8 page_code) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_MODE_SENSE_CMD; + pc->c[0] = MODE_SENSE; if (page_code != IDETAPE_BLOCK_DESCRIPTOR) pc->c[1] = 8; /* DBD = 1 - Don't return block descriptors */ pc->c[2] = page_code; @@ -2293,7 +1602,7 @@ static ide_startstop_t idetape_media_access_finished (ide_drive_t *drive) if (stat & SEEK_STAT) { if (stat & ERR_STAT) { /* Error detected */ - if (pc->c[0] != IDETAPE_TEST_UNIT_READY_CMD) + if (pc->c[0] != TEST_UNIT_READY) printk(KERN_ERR "ide-tape: %s: I/O error, ", tape->name); /* Retry operation */ @@ -2350,8 +1659,8 @@ static ide_startstop_t idetape_rw_callback (ide_drive_t *drive) static void idetape_create_read_cmd(idetape_tape_t *tape, idetape_pc_t *pc, unsigned int length, struct idetape_bh *bh) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_READ_CMD; - put_unaligned(htonl(length), (unsigned int *) &pc->c[1]); + pc->c[0] = READ_6; + put_unaligned(cpu_to_be32(length), (unsigned int *) &pc->c[1]); pc->c[1] = 1; pc->callback = &idetape_rw_callback; pc->bh = bh; @@ -2368,7 +1677,7 @@ static void idetape_create_read_buffer_cmd(idetape_tape_t *tape, idetape_pc_t *p struct idetape_bh *p = bh; idetape_init_pc(pc); - pc->c[0] = IDETAPE_READ_BUFFER_CMD; + pc->c[0] = READ_BUFFER; pc->c[1] = IDETAPE_RETRIEVE_FAULTY_BLOCK; pc->c[7] = size >> 8; pc->c[8] = size & 0xff; @@ -2386,8 +1695,8 @@ static void idetape_create_read_buffer_cmd(idetape_tape_t *tape, idetape_pc_t *p static void idetape_create_write_cmd(idetape_tape_t *tape, idetape_pc_t *pc, unsigned int length, struct idetape_bh *bh) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_WRITE_CMD; - put_unaligned(htonl(length), (unsigned int *) &pc->c[1]); + pc->c[0] = WRITE_6; + put_unaligned(cpu_to_be32(length), (unsigned int *) &pc->c[1]); pc->c[1] = 1; pc->callback = &idetape_rw_callback; set_bit(PC_WRITING, &pc->flags); @@ -2412,12 +1721,6 @@ static ide_startstop_t idetape_do_request(ide_drive_t *drive, u8 stat; #if IDETAPE_DEBUG_LOG -#if 0 - if (tape->debug_level >= 5) - printk(KERN_INFO "ide-tape: %d, " - "dev: %s, cmd: %ld, errors: %d\n", - rq->rq_disk->disk_name, rq->cmd[0], rq->errors); -#endif if (tape->debug_level >= 2) printk(KERN_INFO "ide-tape: sector: %ld, " "nr_sectors: %ld, current_nr_sectors: %d\n", @@ -2438,10 +1741,9 @@ static ide_startstop_t idetape_do_request(ide_drive_t *drive, * Retry a failed packet command */ if (tape->failed_pc != NULL && - tape->pc->c[0] == IDETAPE_REQUEST_SENSE_CMD) { + tape->pc->c[0] == REQUEST_SENSE) { return idetape_issue_packet_command(drive, tape->failed_pc); } -#if IDETAPE_DEBUG_BUGS if (postponed_rq != NULL) if (rq != postponed_rq) { printk(KERN_ERR "ide-tape: ide-tape.c bug - " @@ -2449,7 +1751,6 @@ static ide_startstop_t idetape_do_request(ide_drive_t *drive, idetape_end_request(drive, 0, 0); return ide_stopped; } -#endif /* IDETAPE_DEBUG_BUGS */ tape->postponed_rq = NULL; @@ -2636,13 +1937,11 @@ static int idetape_copy_stage_from_user (idetape_tape_t *tape, idetape_stage_t * int ret = 0; while (n) { -#if IDETAPE_DEBUG_BUGS if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_copy_stage_from_user\n"); return 1; } -#endif /* IDETAPE_DEBUG_BUGS */ count = min((unsigned int)(bh->b_size - atomic_read(&bh->b_count)), (unsigned int)n); if (copy_from_user(bh->b_data + atomic_read(&bh->b_count), buf, count)) ret = 1; @@ -2666,13 +1965,11 @@ static int idetape_copy_stage_to_user (idetape_tape_t *tape, char __user *buf, i int ret = 0; while (n) { -#if IDETAPE_DEBUG_BUGS if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_copy_stage_to_user\n"); return 1; } -#endif /* IDETAPE_DEBUG_BUGS */ count = min(tape->b_count, n); if (copy_to_user(buf, tape->b_data, count)) ret = 1; @@ -2752,12 +2049,10 @@ static void idetape_wait_for_request (ide_drive_t *drive, struct request *rq) DECLARE_COMPLETION_ONSTACK(wait); idetape_tape_t *tape = drive->driver_data; -#if IDETAPE_DEBUG_BUGS if (rq == NULL || !blk_special_request(rq)) { printk (KERN_ERR "ide-tape: bug: Trying to sleep on non-valid request\n"); return; } -#endif /* IDETAPE_DEBUG_BUGS */ rq->end_io_data = &wait; rq->end_io = blk_end_sync_rq; spin_unlock_irq(&tape->spinlock); @@ -2817,7 +2112,7 @@ static ide_startstop_t idetape_read_position_callback (ide_drive_t *drive) static void idetape_create_write_filemark_cmd (ide_drive_t *drive, idetape_pc_t *pc,int write_filemark) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_WRITE_FILEMARK_CMD; + pc->c[0] = WRITE_FILEMARKS; pc->c[4] = write_filemark; set_bit(PC_WAIT_FOR_DSC, &pc->flags); pc->callback = &idetape_pc_callback; @@ -2826,7 +2121,7 @@ static void idetape_create_write_filemark_cmd (ide_drive_t *drive, idetape_pc_t static void idetape_create_test_unit_ready_cmd(idetape_pc_t *pc) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_TEST_UNIT_READY_CMD; + pc->c[0] = TEST_UNIT_READY; pc->callback = &idetape_pc_callback; } @@ -2864,7 +2159,7 @@ static int __idetape_queue_pc_tail (ide_drive_t *drive, idetape_pc_t *pc) static void idetape_create_load_unload_cmd (ide_drive_t *drive, idetape_pc_t *pc,int cmd) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_LOAD_UNLOAD_CMD; + pc->c[0] = START_STOP; pc->c[4] = cmd; set_bit(PC_WAIT_FOR_DSC, &pc->flags); pc->callback = &idetape_pc_callback; @@ -2921,7 +2216,7 @@ static int idetape_flush_tape_buffers (ide_drive_t *drive) static void idetape_create_read_position_cmd (idetape_pc_t *pc) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_READ_POSITION_CMD; + pc->c[0] = READ_POSITION; pc->request_transfer = 20; pc->callback = &idetape_read_position_callback; } @@ -2947,9 +2242,9 @@ static int idetape_read_position (ide_drive_t *drive) static void idetape_create_locate_cmd (ide_drive_t *drive, idetape_pc_t *pc, unsigned int block, u8 partition, int skip) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_LOCATE_CMD; + pc->c[0] = POSITION_TO_ELEMENT; pc->c[1] = 2; - put_unaligned(htonl(block), (unsigned int *) &pc->c[3]); + put_unaligned(cpu_to_be32(block), (unsigned int *) &pc->c[3]); pc->c[8] = partition; set_bit(PC_WAIT_FOR_DSC, &pc->flags); pc->callback = &idetape_pc_callback; @@ -2959,11 +2254,12 @@ static int idetape_create_prevent_cmd (ide_drive_t *drive, idetape_pc_t *pc, int { idetape_tape_t *tape = drive->driver_data; - if (!tape->capabilities.lock) + /* device supports locking according to capabilities page */ + if (!(tape->caps[6] & 0x01)) return 0; idetape_init_pc(pc); - pc->c[0] = IDETAPE_PREVENT_CMD; + pc->c[0] = ALLOW_MEDIUM_REMOVAL; pc->c[4] = prevent; pc->callback = &idetape_pc_callback; return 1; @@ -3072,12 +2368,10 @@ static int idetape_queue_rw_tail(ide_drive_t *drive, int cmd, int blocks, struct if (tape->debug_level >= 2) printk(KERN_INFO "ide-tape: idetape_queue_rw_tail: cmd=%d\n",cmd); #endif /* IDETAPE_DEBUG_LOG */ -#if IDETAPE_DEBUG_BUGS if (idetape_pipeline_active(tape)) { printk(KERN_ERR "ide-tape: bug: the pipeline is active in idetape_queue_rw_tail\n"); return (0); } -#endif /* IDETAPE_DEBUG_BUGS */ idetape_init_rq(&rq, cmd); rq.rq_disk = tape->disk; @@ -3108,7 +2402,7 @@ static void idetape_insert_pipeline_into_queue (ide_drive_t *drive) return; if (!idetape_pipeline_active(tape)) { set_bit(IDETAPE_PIPELINE_ACTIVE, &tape->flags); - idetape_active_next_stage(drive); + idetape_activate_next_stage(drive); (void) ide_do_drive_cmd(drive, tape->active_data_request, ide_end); } } @@ -3116,7 +2410,7 @@ static void idetape_insert_pipeline_into_queue (ide_drive_t *drive) static void idetape_create_inquiry_cmd (idetape_pc_t *pc) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_INQUIRY_CMD; + pc->c[0] = INQUIRY; pc->c[4] = pc->request_transfer = 254; pc->callback = &idetape_pc_callback; } @@ -3124,28 +2418,15 @@ static void idetape_create_inquiry_cmd (idetape_pc_t *pc) static void idetape_create_rewind_cmd (ide_drive_t *drive, idetape_pc_t *pc) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_REWIND_CMD; + pc->c[0] = REZERO_UNIT; set_bit(PC_WAIT_FOR_DSC, &pc->flags); pc->callback = &idetape_pc_callback; } -#if 0 -static void idetape_create_mode_select_cmd (idetape_pc_t *pc, int length) -{ - idetape_init_pc(pc); - set_bit(PC_WRITING, &pc->flags); - pc->c[0] = IDETAPE_MODE_SELECT_CMD; - pc->c[1] = 0x10; - put_unaligned(htons(length), (unsigned short *) &pc->c[3]); - pc->request_transfer = 255; - pc->callback = &idetape_pc_callback; -} -#endif - static void idetape_create_erase_cmd (idetape_pc_t *pc) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_ERASE_CMD; + pc->c[0] = ERASE; pc->c[1] = 1; set_bit(PC_WAIT_FOR_DSC, &pc->flags); pc->callback = &idetape_pc_callback; @@ -3154,8 +2435,8 @@ static void idetape_create_erase_cmd (idetape_pc_t *pc) static void idetape_create_space_cmd (idetape_pc_t *pc,int count, u8 cmd) { idetape_init_pc(pc); - pc->c[0] = IDETAPE_SPACE_CMD; - put_unaligned(htonl(count), (unsigned int *) &pc->c[1]); + pc->c[0] = SPACE; + put_unaligned(cpu_to_be32(count), (unsigned int *) &pc->c[1]); pc->c[1] = cmd; set_bit(PC_WAIT_FOR_DSC, &pc->flags); pc->callback = &idetape_pc_callback; @@ -3275,8 +2556,7 @@ static void idetape_empty_write_pipeline (ide_drive_t *drive) idetape_tape_t *tape = drive->driver_data; int blocks, min; struct idetape_bh *bh; - -#if IDETAPE_DEBUG_BUGS + if (tape->chrdev_direction != idetape_direction_write) { printk(KERN_ERR "ide-tape: bug: Trying to empty write pipeline, but we are not writing.\n"); return; @@ -3285,7 +2565,6 @@ static void idetape_empty_write_pipeline (ide_drive_t *drive) printk(KERN_ERR "ide-tape: bug: merge_buffer too big\n"); tape->merge_stage_size = tape->stage_size; } -#endif /* IDETAPE_DEBUG_BUGS */ if (tape->merge_stage_size) { blocks = tape->merge_stage_size / tape->tape_block_size; if (tape->merge_stage_size % tape->tape_block_size) { @@ -3330,7 +2609,6 @@ static void idetape_empty_write_pipeline (ide_drive_t *drive) * can be totally different on the next backup). */ tape->max_stages = tape->min_pipeline; -#if IDETAPE_DEBUG_BUGS if (tape->first_stage != NULL || tape->next_stage != NULL || tape->last_stage != NULL || @@ -3341,7 +2619,6 @@ static void idetape_empty_write_pipeline (ide_drive_t *drive) tape->first_stage, tape->next_stage, tape->last_stage, tape->nr_stages); } -#endif /* IDETAPE_DEBUG_BUGS */ } static void idetape_restart_speed_control (ide_drive_t *drive) @@ -3364,7 +2641,7 @@ static int idetape_initiate_read (ide_drive_t *drive, int max_stages) idetape_stage_t *new_stage; struct request rq; int bytes_read; - int blocks = tape->capabilities.ctl; + u16 blocks = *(u16 *)&tape->caps[12]; /* Initialize read operation */ if (tape->chrdev_direction != idetape_direction_read) { @@ -3372,12 +2649,10 @@ static int idetape_initiate_read (ide_drive_t *drive, int max_stages) idetape_empty_write_pipeline(drive); idetape_flush_tape_buffers(drive); } -#if IDETAPE_DEBUG_BUGS if (tape->merge_stage || tape->merge_stage_size) { printk (KERN_ERR "ide-tape: merge_stage_size should be 0 now\n"); tape->merge_stage_size = 0; } -#endif /* IDETAPE_DEBUG_BUGS */ if ((tape->merge_stage = __idetape_kmalloc_stage(tape, 0, 0)) == NULL) return -ENOMEM; tape->chrdev_direction = idetape_direction_read; @@ -3478,12 +2753,10 @@ static int idetape_add_chrdev_read_request (ide_drive_t *drive,int blocks) tape->pipeline_head++; calculate_speeds(drive); } -#if IDETAPE_DEBUG_BUGS if (bytes_read > blocks * tape->tape_block_size) { printk(KERN_ERR "ide-tape: bug: trying to return more bytes than requested\n"); bytes_read = blocks * tape->tape_block_size; } -#endif /* IDETAPE_DEBUG_BUGS */ return (bytes_read); } @@ -3567,16 +2840,21 @@ static int idetape_rewind_tape (ide_drive_t *drive) static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, unsigned long arg) { idetape_tape_t *tape = drive->driver_data; - idetape_config_t config; void __user *argp = (void __user *)arg; + struct idetape_config { + int dsc_rw_frequency; + int dsc_media_access_frequency; + int nr_stages; + } config; + #if IDETAPE_DEBUG_LOG if (tape->debug_level >= 4) printk(KERN_INFO "ide-tape: Reached idetape_blkdev_ioctl\n"); #endif /* IDETAPE_DEBUG_LOG */ switch (cmd) { case 0x0340: - if (copy_from_user(&config, argp, sizeof (idetape_config_t))) + if (copy_from_user(&config, argp, sizeof(config))) return -EFAULT; tape->best_dsc_rw_frequency = config.dsc_rw_frequency; tape->max_stages = config.nr_stages; @@ -3584,7 +2862,7 @@ static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, unsigned l case 0x0350: config.dsc_rw_frequency = (int) tape->best_dsc_rw_frequency; config.nr_stages = tape->max_stages; - if (copy_to_user(argp, &config, sizeof (idetape_config_t))) + if (copy_to_user(argp, &config, sizeof(config))) return -EFAULT; break; default: @@ -3608,11 +2886,12 @@ static int idetape_space_over_filemarks (ide_drive_t *drive,short mt_op,int mt_c idetape_pc_t pc; unsigned long flags; int retval,count=0; + int sprev = !!(tape->caps[4] & 0x20); if (mt_count == 0) return 0; if (MTBSF == mt_op || MTBSFM == mt_op) { - if (!tape->capabilities.sprev) + if (!sprev) return -EIO; mt_count = - mt_count; } @@ -3666,7 +2945,7 @@ static int idetape_space_over_filemarks (ide_drive_t *drive,short mt_op,int mt_c return (idetape_queue_pc_tail(drive, &pc)); case MTFSFM: case MTBSFM: - if (!tape->capabilities.sprev) + if (!sprev) return (-EIO); retval = idetape_space_over_filemarks(drive, MTFSF, mt_count-count); if (retval) return (retval); @@ -3703,6 +2982,7 @@ static ssize_t idetape_chrdev_read (struct file *file, char __user *buf, ide_drive_t *drive = tape->drive; ssize_t bytes_read,temp, actually_read = 0, rc; ssize_t ret = 0; + u16 ctl = *(u16 *)&tape->caps[12]; #if IDETAPE_DEBUG_LOG if (tape->debug_level >= 3) @@ -3728,7 +3008,7 @@ static ssize_t idetape_chrdev_read (struct file *file, char __user *buf, count -= actually_read; } while (count >= tape->stage_size) { - bytes_read = idetape_add_chrdev_read_request(drive, tape->capabilities.ctl); + bytes_read = idetape_add_chrdev_read_request(drive, ctl); if (bytes_read <= 0) goto finish; if (idetape_copy_stage_to_user(tape, buf, tape->merge_stage, bytes_read)) @@ -3738,7 +3018,7 @@ static ssize_t idetape_chrdev_read (struct file *file, char __user *buf, actually_read += bytes_read; } if (count) { - bytes_read = idetape_add_chrdev_read_request(drive, tape->capabilities.ctl); + bytes_read = idetape_add_chrdev_read_request(drive, ctl); if (bytes_read <= 0) goto finish; temp = min((unsigned long)count, (unsigned long)bytes_read); @@ -3767,6 +3047,7 @@ static ssize_t idetape_chrdev_write (struct file *file, const char __user *buf, ide_drive_t *drive = tape->drive; ssize_t actually_written = 0; ssize_t ret = 0; + u16 ctl = *(u16 *)&tape->caps[12]; /* The drive is write protected. */ if (tape->write_prot) @@ -3782,13 +3063,11 @@ static ssize_t idetape_chrdev_write (struct file *file, const char __user *buf, if (tape->chrdev_direction != idetape_direction_write) { if (tape->chrdev_direction == idetape_direction_read) idetape_discard_read_pipeline(drive, 1); -#if IDETAPE_DEBUG_BUGS if (tape->merge_stage || tape->merge_stage_size) { printk(KERN_ERR "ide-tape: merge_stage_size " "should be 0 now\n"); tape->merge_stage_size = 0; } -#endif /* IDETAPE_DEBUG_BUGS */ if ((tape->merge_stage = __idetape_kmalloc_stage(tape, 0, 0)) == NULL) return -ENOMEM; tape->chrdev_direction = idetape_direction_write; @@ -3816,12 +3095,10 @@ static ssize_t idetape_chrdev_write (struct file *file, const char __user *buf, if (tape->restart_speed_control_req) idetape_restart_speed_control(drive); if (tape->merge_stage_size) { -#if IDETAPE_DEBUG_BUGS if (tape->merge_stage_size >= tape->stage_size) { printk(KERN_ERR "ide-tape: bug: merge buffer too big\n"); tape->merge_stage_size = 0; } -#endif /* IDETAPE_DEBUG_BUGS */ actually_written = min((unsigned int)(tape->stage_size - tape->merge_stage_size), (unsigned int)count); if (idetape_copy_stage_from_user(tape, tape->merge_stage, buf, actually_written)) ret = -EFAULT; @@ -3832,7 +3109,7 @@ static ssize_t idetape_chrdev_write (struct file *file, const char __user *buf, if (tape->merge_stage_size == tape->stage_size) { ssize_t retval; tape->merge_stage_size = 0; - retval = idetape_add_chrdev_write_request(drive, tape->capabilities.ctl); + retval = idetape_add_chrdev_write_request(drive, ctl); if (retval <= 0) return (retval); } @@ -3843,7 +3120,7 @@ static ssize_t idetape_chrdev_write (struct file *file, const char __user *buf, ret = -EFAULT; buf += tape->stage_size; count -= tape->stage_size; - retval = idetape_add_chrdev_write_request(drive, tape->capabilities.ctl); + retval = idetape_add_chrdev_write_request(drive, ctl); actually_written += tape->stage_size; if (retval <= 0) return (retval); @@ -3871,69 +3148,20 @@ static int idetape_write_filemark (ide_drive_t *drive) } /* - * idetape_mtioctop is called from idetape_chrdev_ioctl when - * the general mtio MTIOCTOP ioctl is requested. - * - * We currently support the following mtio.h operations: + * Called from idetape_chrdev_ioctl when the general mtio MTIOCTOP ioctl is + * requested. * - * MTFSF - Space over mt_count filemarks in the positive direction. - * The tape is positioned after the last spaced filemark. + * Note: MTBSF and MTBSFM are not supported when the tape doesn't support + * spacing over filemarks in the reverse direction. In this case, MTFSFM is also + * usually not supported (it is supported in the rare case in which we crossed + * the filemark during our read-ahead pipelined operation mode). * - * MTFSFM - Same as MTFSF, but the tape is positioned before the - * last filemark. + * The following commands are currently not supported: * - * MTBSF - Steps background over mt_count filemarks, tape is - * positioned before the last filemark. - * - * MTBSFM - Like MTBSF, only tape is positioned after the last filemark. - * - * Note: - * - * MTBSF and MTBSFM are not supported when the tape doesn't - * support spacing over filemarks in the reverse direction. - * In this case, MTFSFM is also usually not supported (it is - * supported in the rare case in which we crossed the filemark - * during our read-ahead pipelined operation mode). - * - * MTWEOF - Writes mt_count filemarks. Tape is positioned after - * the last written filemark. - * - * MTREW - Rewinds tape. - * - * MTLOAD - Loads the tape. - * - * MTOFFL - Puts the tape drive "Offline": Rewinds the tape and - * MTUNLOAD prevents further access until the media is replaced. - * - * MTNOP - Flushes tape buffers. - * - * MTRETEN - Retension media. This typically consists of one end - * to end pass on the media. - * - * MTEOM - Moves to the end of recorded data. - * - * MTERASE - Erases tape. - * - * MTSETBLK - Sets the user block size to mt_count bytes. If - * mt_count is 0, we will attempt to autodetect - * the block size. - * - * MTSEEK - Positions the tape in a specific block number, where - * each block is assumed to contain which user_block_size - * bytes. - * - * MTSETPART - Switches to another tape partition. - * - * MTLOCK - Locks the tape door. - * - * MTUNLOCK - Unlocks the tape door. - * - * The following commands are currently not supported: - * - * MTFSS, MTBSS, MTWSM, MTSETDENSITY, - * MTSETDRVBUFFER, MT_ST_BOOLEANS, MT_ST_WRITE_THRESHOLD. + * MTFSS, MTBSS, MTWSM, MTSETDENSITY, MTSETDRVBUFFER, MT_ST_BOOLEANS, + * MT_ST_WRITE_THRESHOLD. */ -static int idetape_mtioctop (ide_drive_t *drive,short mt_op,int mt_count) +static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) { idetape_tape_t *tape = drive->driver_data; idetape_pc_t pc; @@ -4048,29 +3276,12 @@ static int idetape_mtioctop (ide_drive_t *drive,short mt_op,int mt_count) } /* - * Our character device ioctls. - * - * General mtio.h magnetic io commands are supported here, and not in - * the corresponding block interface. - * - * The following ioctls are supported: - * - * MTIOCTOP - Refer to idetape_mtioctop for detailed description. - * - * MTIOCGET - The mt_dsreg field in the returned mtget structure - * will be set to (user block size in bytes << - * MT_ST_BLKSIZE_SHIFT) & MT_ST_BLKSIZE_MASK. - * - * The mt_blkno is set to the current user block number. - * The other mtget fields are not supported. - * - * MTIOCPOS - The current tape "block position" is returned. We - * assume that each block contains user_block_size - * bytes. - * - * Our own ide-tape ioctls are supported on both interfaces. + * Our character device ioctls. General mtio.h magnetic io commands are + * supported here, and not in the corresponding block interface. Our own + * ide-tape ioctls are supported on both interfaces. */ -static int idetape_chrdev_ioctl (struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) +static int idetape_chrdev_ioctl(struct inode *inode, struct file *file, + unsigned int cmd, unsigned long arg) { struct ide_tape_obj *tape = ide_tape_f(file); ide_drive_t *drive = tape->drive; @@ -4124,7 +3335,30 @@ static int idetape_chrdev_ioctl (struct inode *inode, struct file *file, unsigne } } -static void idetape_get_blocksize_from_block_descriptor(ide_drive_t *drive); +/* + * Do a mode sense page 0 with block descriptor and if it succeeds set the tape + * block size with the reported value. + */ +static void ide_tape_get_bsize_from_bdesc(ide_drive_t *drive) +{ + idetape_tape_t *tape = drive->driver_data; + idetape_pc_t pc; + + idetape_create_mode_sense_cmd(&pc, IDETAPE_BLOCK_DESCRIPTOR); + if (idetape_queue_pc_tail(drive, &pc)) { + printk(KERN_ERR "ide-tape: Can't get block descriptor\n"); + if (tape->tape_block_size == 0) { + printk(KERN_WARNING "ide-tape: Cannot deal with zero " + "block size, assuming 32k\n"); + tape->tape_block_size = 32768; + } + return; + } + tape->tape_block_size = (pc.buffer[4 + 5] << 16) + + (pc.buffer[4 + 6] << 8) + + pc.buffer[4 + 7]; + tape->drv_write_prot = (pc.buffer[2] & 0x80) >> 7; +} /* * Our character device open function. @@ -4178,7 +3412,7 @@ static int idetape_chrdev_open (struct inode *inode, struct file *filp) clear_bit(IDETAPE_PIPELINE_ERROR, &tape->flags); /* Read block size and write protect status from drive. */ - idetape_get_blocksize_from_block_descriptor(drive); + ide_tape_get_bsize_from_bdesc(drive); /* Set write protect flag if device is opened as read-only. */ if ((filp->f_flags & O_ACCMODE) == O_RDONLY) @@ -4296,190 +3530,100 @@ static int idetape_identify_device (ide_drive_t *drive) *((unsigned short *) &gcw) = id->config; -#if IDETAPE_DEBUG_INFO - printk(KERN_INFO "ide-tape: Dumping ATAPI Identify Device tape parameters\n"); - printk(KERN_INFO "ide-tape: Protocol Type: "); - switch (gcw.protocol) { - case 0: case 1: printk("ATA\n");break; - case 2: printk("ATAPI\n");break; - case 3: printk("Reserved (Unknown to ide-tape)\n");break; - } - printk(KERN_INFO "ide-tape: Device Type: %x - ",gcw.device_type); - switch (gcw.device_type) { - case 0: printk("Direct-access Device\n");break; - case 1: printk("Streaming Tape Device\n");break; - case 2: case 3: case 4: printk("Reserved\n");break; - case 5: printk("CD-ROM Device\n");break; - case 6: printk("Reserved\n"); - case 7: printk("Optical memory Device\n");break; - case 0x1f: printk("Unknown or no Device type\n");break; - default: printk("Reserved\n"); - } - printk(KERN_INFO "ide-tape: Removable: %s",gcw.removable ? "Yes\n":"No\n"); - printk(KERN_INFO "ide-tape: Command Packet DRQ Type: "); - switch (gcw.drq_type) { - case 0: printk("Microprocessor DRQ\n");break; - case 1: printk("Interrupt DRQ\n");break; - case 2: printk("Accelerated DRQ\n");break; - case 3: printk("Reserved\n");break; - } - printk(KERN_INFO "ide-tape: Command Packet Size: "); - switch (gcw.packet_size) { - case 0: printk("12 bytes\n");break; - case 1: printk("16 bytes\n");break; - default: printk("Reserved\n");break; - } -#endif /* IDETAPE_DEBUG_INFO */ - /* Check that we can support this device */ - if (gcw.protocol !=2 ) - printk(KERN_ERR "ide-tape: Protocol is not ATAPI\n"); + if (gcw.protocol != 2) + printk(KERN_ERR "ide-tape: Protocol (0x%02x) is not ATAPI\n", + gcw.protocol); else if (gcw.device_type != 1) - printk(KERN_ERR "ide-tape: Device type is not set to tape\n"); + printk(KERN_ERR "ide-tape: Device type (0x%02x) is not set " + "to tape\n", gcw.device_type); else if (!gcw.removable) printk(KERN_ERR "ide-tape: The removable flag is not set\n"); else if (gcw.packet_size != 0) { - printk(KERN_ERR "ide-tape: Packet size is not 12 bytes long\n"); - if (gcw.packet_size == 1) - printk(KERN_ERR "ide-tape: Sorry, padding to 16 bytes is still not supported\n"); + printk(KERN_ERR "ide-tape: Packet size (0x%02x) is not 12 " + "bytes long\n", gcw.packet_size); } else return 1; return 0; } -/* - * Use INQUIRY to get the firmware revision - */ -static void idetape_get_inquiry_results (ide_drive_t *drive) +static void idetape_get_inquiry_results(ide_drive_t *drive) { char *r; idetape_tape_t *tape = drive->driver_data; idetape_pc_t pc; - idetape_inquiry_result_t *inquiry; - + idetape_create_inquiry_cmd(&pc); if (idetape_queue_pc_tail(drive, &pc)) { - printk(KERN_ERR "ide-tape: %s: can't get INQUIRY results\n", tape->name); + printk(KERN_ERR "ide-tape: %s: can't get INQUIRY results\n", + tape->name); return; } - inquiry = (idetape_inquiry_result_t *) pc.buffer; - memcpy(tape->vendor_id, inquiry->vendor_id, 8); - memcpy(tape->product_id, inquiry->product_id, 16); - memcpy(tape->firmware_revision, inquiry->revision_level, 4); + memcpy(tape->vendor_id, &pc.buffer[8], 8); + memcpy(tape->product_id, &pc.buffer[16], 16); + memcpy(tape->firmware_revision, &pc.buffer[32], 4); + ide_fixstring(tape->vendor_id, 10, 0); ide_fixstring(tape->product_id, 18, 0); ide_fixstring(tape->firmware_revision, 6, 0); r = tape->firmware_revision; if (*(r + 1) == '.') - tape->firmware_revision_num = (*r - '0') * 100 + (*(r + 2) - '0') * 10 + *(r + 3) - '0'; - printk(KERN_INFO "ide-tape: %s <-> %s: %s %s rev %s\n", drive->name, tape->name, tape->vendor_id, tape->product_id, tape->firmware_revision); + tape->firmware_revision_num = (*r - '0') * 100 + + (*(r + 2) - '0') * 10 + *(r + 3) - '0'; + printk(KERN_INFO "ide-tape: %s <-> %s: %s %s rev %s\n", + drive->name, tape->name, tape->vendor_id, + tape->product_id, tape->firmware_revision); } /* - * idetape_get_mode_sense_results asks the tape about its various - * parameters. In particular, we will adjust our data transfer buffer - * size to the recommended value as returned by the tape. + * Ask the tape about its various parameters. In particular, we will adjust our + * data transfer buffer size to the recommended value as returned by the tape. */ static void idetape_get_mode_sense_results (ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; idetape_pc_t pc; - idetape_mode_parameter_header_t *header; - idetape_capabilities_page_t *capabilities; - + u8 *caps; + u8 speed, max_speed; + idetape_create_mode_sense_cmd(&pc, IDETAPE_CAPABILITIES_PAGE); if (idetape_queue_pc_tail(drive, &pc)) { - printk(KERN_ERR "ide-tape: Can't get tape parameters - assuming some default values\n"); + printk(KERN_ERR "ide-tape: Can't get tape parameters - assuming" + " some default values\n"); tape->tape_block_size = 512; - tape->capabilities.ctl = 52; - tape->capabilities.speed = 450; - tape->capabilities.buffer_size = 6 * 52; + put_unaligned(52, (u16 *)&tape->caps[12]); + put_unaligned(540, (u16 *)&tape->caps[14]); + put_unaligned(6*52, (u16 *)&tape->caps[16]); return; } - header = (idetape_mode_parameter_header_t *) pc.buffer; - capabilities = (idetape_capabilities_page_t *) (pc.buffer + sizeof(idetape_mode_parameter_header_t) + header->bdl); + caps = pc.buffer + 4 + pc.buffer[3]; - capabilities->max_speed = ntohs(capabilities->max_speed); - capabilities->ctl = ntohs(capabilities->ctl); - capabilities->speed = ntohs(capabilities->speed); - capabilities->buffer_size = ntohs(capabilities->buffer_size); + /* convert to host order and save for later use */ + speed = be16_to_cpu(*(u16 *)&caps[14]); + max_speed = be16_to_cpu(*(u16 *)&caps[8]); - if (!capabilities->speed) { - printk(KERN_INFO "ide-tape: %s: overriding capabilities->speed (assuming 650KB/sec)\n", drive->name); - capabilities->speed = 650; + put_unaligned(max_speed, (u16 *)&caps[8]); + put_unaligned(be16_to_cpu(*(u16 *)&caps[12]), (u16 *)&caps[12]); + put_unaligned(speed, (u16 *)&caps[14]); + put_unaligned(be16_to_cpu(*(u16 *)&caps[16]), (u16 *)&caps[16]); + + if (!speed) { + printk(KERN_INFO "ide-tape: %s: invalid tape speed " + "(assuming 650KB/sec)\n", drive->name); + put_unaligned(650, (u16 *)&caps[14]); } - if (!capabilities->max_speed) { - printk(KERN_INFO "ide-tape: %s: overriding capabilities->max_speed (assuming 650KB/sec)\n", drive->name); - capabilities->max_speed = 650; + if (!max_speed) { + printk(KERN_INFO "ide-tape: %s: invalid max_speed " + "(assuming 650KB/sec)\n", drive->name); + put_unaligned(650, (u16 *)&caps[8]); } - tape->capabilities = *capabilities; /* Save us a copy */ - if (capabilities->blk512) + memcpy(&tape->caps, caps, 20); + if (caps[7] & 0x02) tape->tape_block_size = 512; - else if (capabilities->blk1024) + else if (caps[7] & 0x04) tape->tape_block_size = 1024; - -#if IDETAPE_DEBUG_INFO - printk(KERN_INFO "ide-tape: Dumping the results of the MODE SENSE packet command\n"); - printk(KERN_INFO "ide-tape: Mode Parameter Header:\n"); - printk(KERN_INFO "ide-tape: Mode Data Length - %d\n",header->mode_data_length); - printk(KERN_INFO "ide-tape: Medium Type - %d\n",header->medium_type); - printk(KERN_INFO "ide-tape: Device Specific Parameter - %d\n",header->dsp); - printk(KERN_INFO "ide-tape: Block Descriptor Length - %d\n",header->bdl); - - printk(KERN_INFO "ide-tape: Capabilities and Mechanical Status Page:\n"); - printk(KERN_INFO "ide-tape: Page code - %d\n",capabilities->page_code); - printk(KERN_INFO "ide-tape: Page length - %d\n",capabilities->page_length); - printk(KERN_INFO "ide-tape: Read only - %s\n",capabilities->ro ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports reverse space - %s\n",capabilities->sprev ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports erase initiated formatting - %s\n",capabilities->efmt ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports QFA two Partition format - %s\n",capabilities->qfa ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports locking the medium - %s\n",capabilities->lock ? "Yes":"No"); - printk(KERN_INFO "ide-tape: The volume is currently locked - %s\n",capabilities->locked ? "Yes":"No"); - printk(KERN_INFO "ide-tape: The device defaults in the prevent state - %s\n",capabilities->prevent ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports ejecting the medium - %s\n",capabilities->eject ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports error correction - %s\n",capabilities->ecc ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports data compression - %s\n",capabilities->cmprs ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports 512 bytes block size - %s\n",capabilities->blk512 ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports 1024 bytes block size - %s\n",capabilities->blk1024 ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Supports 32768 bytes block size / Restricted byte count for PIO transfers - %s\n",capabilities->blk32768 ? "Yes":"No"); - printk(KERN_INFO "ide-tape: Maximum supported speed in KBps - %d\n",capabilities->max_speed); - printk(KERN_INFO "ide-tape: Continuous transfer limits in blocks - %d\n",capabilities->ctl); - printk(KERN_INFO "ide-tape: Current speed in KBps - %d\n",capabilities->speed); - printk(KERN_INFO "ide-tape: Buffer size - %d\n",capabilities->buffer_size*512); -#endif /* IDETAPE_DEBUG_INFO */ -} - -/* - * ide_get_blocksize_from_block_descriptor does a mode sense page 0 with block descriptor - * and if it succeeds sets the tape block size with the reported value - */ -static void idetape_get_blocksize_from_block_descriptor(ide_drive_t *drive) -{ - - idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; - idetape_mode_parameter_header_t *header; - idetape_parameter_block_descriptor_t *block_descrp; - - idetape_create_mode_sense_cmd(&pc, IDETAPE_BLOCK_DESCRIPTOR); - if (idetape_queue_pc_tail(drive, &pc)) { - printk(KERN_ERR "ide-tape: Can't get block descriptor\n"); - if (tape->tape_block_size == 0) { - printk(KERN_WARNING "ide-tape: Cannot deal with zero block size, assume 32k\n"); - tape->tape_block_size = 32768; - } - return; - } - header = (idetape_mode_parameter_header_t *) pc.buffer; - block_descrp = (idetape_parameter_block_descriptor_t *) (pc.buffer + sizeof(idetape_mode_parameter_header_t)); - tape->tape_block_size =( block_descrp->length[0]<<16) + (block_descrp->length[1]<<8) + block_descrp->length[2]; - tape->drv_write_prot = (header->dsp & 0x80) >> 7; - -#if IDETAPE_DEBUG_INFO - printk(KERN_INFO "ide-tape: Adjusted block size - %d\n", tape->tape_block_size); -#endif /* IDETAPE_DEBUG_INFO */ } #ifdef CONFIG_IDE_PROC_FS @@ -4490,13 +3634,15 @@ static void idetape_add_settings (ide_drive_t *drive) /* * drive setting name read/write data type min max mul_factor div_factor data pointer set function */ - ide_add_setting(drive, "buffer", SETTING_READ, TYPE_SHORT, 0, 0xffff, 1, 2, &tape->capabilities.buffer_size, NULL); + ide_add_setting(drive, "buffer", SETTING_READ, TYPE_SHORT, 0, 0xffff, + 1, 2, (u16 *)&tape->caps[16], NULL); ide_add_setting(drive, "pipeline_min", SETTING_RW, TYPE_INT, 1, 0xffff, tape->stage_size / 1024, 1, &tape->min_pipeline, NULL); ide_add_setting(drive, "pipeline", SETTING_RW, TYPE_INT, 1, 0xffff, tape->stage_size / 1024, 1, &tape->max_stages, NULL); ide_add_setting(drive, "pipeline_max", SETTING_RW, TYPE_INT, 1, 0xffff, tape->stage_size / 1024, 1, &tape->max_pipeline, NULL); ide_add_setting(drive, "pipeline_used", SETTING_READ, TYPE_INT, 0, 0xffff, tape->stage_size / 1024, 1, &tape->nr_stages, NULL); ide_add_setting(drive, "pipeline_pending", SETTING_READ, TYPE_INT, 0, 0xffff, tape->stage_size / 1024, 1, &tape->nr_pending_stages, NULL); - ide_add_setting(drive, "speed", SETTING_READ, TYPE_SHORT, 0, 0xffff, 1, 1, &tape->capabilities.speed, NULL); + ide_add_setting(drive, "speed", SETTING_READ, TYPE_SHORT, 0, 0xffff, + 1, 1, (u16 *)&tape->caps[14], NULL); ide_add_setting(drive, "stage", SETTING_READ, TYPE_INT, 0, 0xffff, 1, 1024, &tape->stage_size, NULL); ide_add_setting(drive, "tdsc", SETTING_RW, TYPE_INT, IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX, 1000, HZ, &tape->best_dsc_rw_frequency, NULL); ide_add_setting(drive, "dsc_overlap", SETTING_RW, TYPE_BYTE, 0, 1, 1, 1, &drive->dsc_overlap, NULL); @@ -4528,6 +3674,7 @@ static void idetape_setup (ide_drive_t *drive, idetape_tape_t *tape, int minor) struct idetape_id_gcw gcw; int stage_size; struct sysinfo si; + u16 *ctl = (u16 *)&tape->caps[12]; spin_lock_init(&tape->spinlock); drive->dsc_overlap = 1; @@ -4555,13 +3702,13 @@ static void idetape_setup (ide_drive_t *drive, idetape_tape_t *tape, int minor) idetape_get_inquiry_results(drive); idetape_get_mode_sense_results(drive); - idetape_get_blocksize_from_block_descriptor(drive); + ide_tape_get_bsize_from_bdesc(drive); tape->user_bs_factor = 1; - tape->stage_size = tape->capabilities.ctl * tape->tape_block_size; + tape->stage_size = *ctl * tape->tape_block_size; while (tape->stage_size > 0xffff) { printk(KERN_NOTICE "ide-tape: decreasing stage size\n"); - tape->capabilities.ctl /= 2; - tape->stage_size = tape->capabilities.ctl * tape->tape_block_size; + *ctl /= 2; + tape->stage_size = *ctl * tape->tape_block_size; } stage_size = tape->stage_size; tape->pages_per_stage = stage_size / PAGE_SIZE; @@ -4570,11 +3717,8 @@ static void idetape_setup (ide_drive_t *drive, idetape_tape_t *tape, int minor) tape->excess_bh_size = PAGE_SIZE - stage_size % PAGE_SIZE; } - /* - * Select the "best" DSC read/write polling frequency - * and pipeline size. - */ - speed = max(tape->capabilities.speed, tape->capabilities.max_speed); + /* Select the "best" DSC read/write polling freq and pipeline size. */ + speed = max(*(u16 *)&tape->caps[14], *(u16 *)&tape->caps[8]); tape->max_stages = speed * 1000 * 10 / tape->stage_size; @@ -4591,7 +3735,7 @@ static void idetape_setup (ide_drive_t *drive, idetape_tape_t *tape, int minor) tape->max_stages = tape->min_pipeline = tape->max_pipeline = 1; t1 = (tape->stage_size * HZ) / (speed * 1000); - tmid = (tape->capabilities.buffer_size * 32 * HZ) / (speed * 125); + tmid = (*(u16 *)&tape->caps[16] * 32 * HZ) / (speed * 125); tn = (IDETAPE_FIFO_THRESHOLD * tape->stage_size * HZ) / (speed * 1000); if (tape->max_stages) @@ -4606,8 +3750,8 @@ static void idetape_setup (ide_drive_t *drive, idetape_tape_t *tape, int minor) tape->best_dsc_rw_frequency = max_t(unsigned long, min_t(unsigned long, t, IDETAPE_DSC_RW_MAX), IDETAPE_DSC_RW_MIN); printk(KERN_INFO "ide-tape: %s <-> %s: %dKBps, %d*%dkB buffer, " "%dkB pipeline, %lums tDSC%s\n", - drive->name, tape->name, tape->capabilities.speed, - (tape->capabilities.buffer_size * 512) / tape->stage_size, + drive->name, tape->name, *(u16 *)&tape->caps[14], + (*(u16 *)&tape->caps[16] * 512) / tape->stage_size, tape->stage_size / 1024, tape->max_stages * tape->stage_size / 1024, tape->best_dsc_rw_frequency * 1000 / HZ, |