aboutsummaryrefslogtreecommitdiff
path: root/drivers/ide/pci
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide/pci')
-rw-r--r--drivers/ide/pci/alim15x3.c42
-rw-r--r--drivers/ide/pci/cmd640.c2
-rw-r--r--drivers/ide/pci/cs5520.c2
-rw-r--r--drivers/ide/pci/delkin_cb.c28
-rw-r--r--drivers/ide/pci/opti621.c221
-rw-r--r--drivers/ide/pci/sis5513.c5
6 files changed, 71 insertions, 229 deletions
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index c1922f9cfe8..f2129d5e07f 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -39,6 +39,16 @@
#include <asm/io.h>
/*
+ * Allow UDMA on M1543C-E chipset for WDC disks that ignore CRC checking
+ * (this is DANGEROUS and could result in data corruption).
+ */
+static int wdc_udma;
+
+module_param(wdc_udma, bool, 0);
+MODULE_PARM_DESC(wdc_udma,
+ "allow UDMA on M1543C-E chipset for WDC disks (DANGEROUS)");
+
+/*
* ALi devices are not plug in. Otherwise these static values would
* need to go. They ought to go away anyway
*/
@@ -76,11 +86,6 @@ static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
a_clc = 0;
c_time = ide_pio_timings[pio].cycle_time;
-#if 0
- if ((r_clc = ((c_time - s_time - a_time) * bus_speed + 999) / 1000) >= 16)
- r_clc = 0;
-#endif
-
if (!(r_clc = (c_time * bus_speed + 999) / 1000 - a_clc - s_clc)) {
r_clc = 1;
} else {
@@ -110,16 +115,6 @@ static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
pci_write_config_byte(dev, port, s_clc);
pci_write_config_byte(dev, port+drive->select.b.unit+2, (a_clc << 4) | r_clc);
local_irq_restore(flags);
-
- /*
- * setup active rec
- * { 70, 165, 365 }, PIO Mode 0
- * { 50, 125, 208 }, PIO Mode 1
- * { 30, 100, 110 }, PIO Mode 2
- * { 30, 80, 70 }, PIO Mode 3 with IORDY
- * { 25, 70, 25 }, PIO Mode 4 with IORDY ns
- * { 20, 50, 30 } PIO Mode 5 with IORDY (nonstandard)
- */
}
/**
@@ -131,9 +126,7 @@ static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
* The actual rules for the ALi are:
* No UDMA on revisions <= 0x20
* Disk only for revisions < 0xC2
- * Not WDC drives for revisions < 0xC2
- *
- * FIXME: WDC ifdef needs to die
+ * Not WDC drives on M1543C-E (?)
*/
static u8 ali_udma_filter(ide_drive_t *drive)
@@ -141,10 +134,9 @@ static u8 ali_udma_filter(ide_drive_t *drive)
if (m5229_revision > 0x20 && m5229_revision < 0xC2) {
if (drive->media != ide_disk)
return 0;
-#ifndef CONFIG_WDC_ALI15X3
- if (chip_is_1543c_e && strstr(drive->id->model, "WDC "))
+ if (chip_is_1543c_e && strstr(drive->id->model, "WDC ") &&
+ wdc_udma == 0)
return 0;
-#endif
}
return drive->hwif->ultra_mask;
@@ -537,17 +529,9 @@ static const struct ide_port_info ali15x3_chipset __devinitdata = {
static int __devinit alim15x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct pci_device_id ati_rs100[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100) },
- { },
- };
-
struct ide_port_info d = ali15x3_chipset;
u8 rev = dev->revision, idx = id->driver_data;
- if (pci_dev_present(ati_rs100))
- printk(KERN_WARNING "alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.\n");
-
/* don't use LBA48 DMA on ALi devices before rev 0xC5 */
if (rev <= 0xC4)
d.host_flags |= IDE_HFLAG_NO_LBA48_DMA;
diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c
index aaf38109eae..b38a1980dcd 100644
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -747,9 +747,11 @@ static int __init cmd640x_init(void)
ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
hw[0].irq = 14;
+ hw[0].chipset = ide_cmd640;
ide_std_init_ports(&hw[1], 0x170, 0x376);
hw[1].irq = 15;
+ hw[1].chipset = ide_cmd640;
printk(KERN_INFO "cmd640: buggy cmd640%c interface on %s, config=0x%02x"
"\n", 'a' + cmd640_chip_version - 1, bus_type, cfr);
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index 17669a43443..992b1cf8db6 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -119,6 +119,7 @@ static const struct ide_dma_ops cs5520_dma_ops = {
.dma_timeout = ide_dma_timeout,
};
+/* FIXME: VDMA is disabled because it caused system hangs */
#define DECLARE_CS_DEV(name_str) \
{ \
.name = name_str, \
@@ -126,7 +127,6 @@ static const struct ide_dma_ops cs5520_dma_ops = {
.dma_ops = &cs5520_dma_ops, \
.host_flags = IDE_HFLAG_ISA_PORTS | \
IDE_HFLAG_CS5520 | \
- IDE_HFLAG_VDMA | \
IDE_HFLAG_NO_ATAPI_DMA | \
IDE_HFLAG_ABUSE_SET_DMA_MODE, \
.pio_mask = ATA_PIO4, \
diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c
index b9e457996d0..af0f30051d5 100644
--- a/drivers/ide/pci/delkin_cb.c
+++ b/drivers/ide/pci/delkin_cb.c
@@ -47,13 +47,18 @@ static const struct ide_port_ops delkin_cb_port_ops = {
.quirkproc = ide_undecoded_slave,
};
+static const struct ide_port_info delkin_cb_port_info = {
+ .port_ops = &delkin_cb_port_ops,
+ .host_flags = IDE_HFLAG_IO_32BIT | IDE_HFLAG_UNMASK_IRQS |
+ IDE_HFLAG_NO_DMA,
+};
+
static int __devinit
delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
{
unsigned long base;
hw_regs_t hw;
ide_hwif_t *hwif = NULL;
- ide_drive_t *drive;
int i, rc;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
@@ -79,6 +84,7 @@ delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
memset(&hw, 0, sizeof(hw));
ide_std_init_ports(&hw, base + 0x10, base + 0x1e);
hw.irq = dev->irq;
+ hw.dev = &dev->dev;
hw.chipset = ide_pci; /* this enables IRQ sharing */
hwif = ide_find_port();
@@ -89,26 +95,16 @@ delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
ide_init_port_data(hwif, i);
ide_init_port_hw(hwif, &hw);
- hwif->port_ops = &delkin_cb_port_ops;
idx[0] = i;
- ide_device_add(idx, NULL);
-
- if (!hwif->present)
- goto out_disable;
+ ide_device_add(idx, &delkin_cb_port_info);
pci_set_drvdata(dev, hwif);
- hwif->dev = &dev->dev;
- drive = &hwif->drives[0];
- if (drive->present) {
- drive->io_32bit = 1;
- drive->unmask = 1;
- }
+
return 0;
out_disable:
- printk(KERN_ERR "delkin_cb: no IDE devices found\n");
pci_release_regions(dev);
pci_disable_device(dev);
return -ENODEV;
@@ -139,14 +135,12 @@ static struct pci_driver driver = {
.remove = delkin_cb_remove,
};
-static int
-delkin_cb_init (void)
+static int __init delkin_cb_init(void)
{
return pci_register_driver(&driver);
}
-static void
-delkin_cb_exit (void)
+static void __exit delkin_cb_exit(void)
{
pci_unregister_driver(&driver);
}
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
index 6e99080497b..725c80508d9 100644
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -81,8 +81,6 @@
* 0.5 doesn't work.
*/
-#define OPTI621_DEBUG /* define for debug messages */
-
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
@@ -92,28 +90,6 @@
#include <asm/io.h>
-//#define OPTI621_MAX_PIO 3
-/* In fact, I do not have any PIO 4 drive
- * (address: 25 ns, data: 70 ns, recovery: 35 ns),
- * but OPTi 82C621 is programmable and it can do (minimal values):
- * on 40MHz PCI bus (pulse 25 ns):
- * address: 25 ns, data: 25 ns, recovery: 50 ns;
- * on 20MHz PCI bus (pulse 50 ns):
- * address: 50 ns, data: 50 ns, recovery: 100 ns.
- */
-
-/* #define READ_PREFETCH 0 */
-/* Uncomment for disable read prefetch.
- * There is some readprefetch capatibility in hdparm,
- * but when I type hdparm -P 1 /dev/hda, I got errors
- * and till reset drive is inaccessible.
- * This (hw) read prefetch is safe on my drive.
- */
-
-#ifndef READ_PREFETCH
-#define READ_PREFETCH 0x40 /* read prefetch is enabled */
-#endif /* else read prefetch is disabled */
-
#define READ_REG 0 /* index of Read cycle timing register */
#define WRITE_REG 1 /* index of Write cycle timing register */
#define CNTRL_REG 3 /* index of Control register */
@@ -122,51 +98,8 @@
static int reg_base;
-#define PIO_NOT_EXIST 254
-#define PIO_DONT_KNOW 255
-
static DEFINE_SPINLOCK(opti621_lock);
-/* there are stored pio numbers from other calls of opti621_set_pio_mode */
-static void compute_pios(ide_drive_t *drive, const u8 pio)
-/* Store values into drive->drive_data
- * second_contr - 0 for primary controller, 1 for secondary
- * slave_drive - 0 -> pio is for master, 1 -> pio is for slave
- * pio - PIO mode for selected drive (for other we don't know)
- */
-{
- int d;
- ide_hwif_t *hwif = HWIF(drive);
-
- drive->drive_data = pio;
-
- for (d = 0; d < 2; ++d) {
- drive = &hwif->drives[d];
- if (drive->present) {
- if (drive->drive_data == PIO_DONT_KNOW)
- drive->drive_data = ide_get_best_pio_mode(drive, 255, 3);
-#ifdef OPTI621_DEBUG
- printk("%s: Selected PIO mode %d\n",
- drive->name, drive->drive_data);
-#endif
- } else {
- drive->drive_data = PIO_NOT_EXIST;
- }
- }
-}
-
-static int cmpt_clk(int time, int bus_speed)
-/* Returns (rounded up) time in clocks for time in ns,
- * with bus_speed in MHz.
- * Example: bus_speed = 40 MHz, time = 80 ns
- * 1000/40 = 25 ns (clk value),
- * 80/25 = 3.2, rounded up to 4 (I hope ;-)).
- * Use idebus=xx to select right frequency.
- */
-{
- return ((time*bus_speed+999)/1000);
-}
-
/* Write value to register reg, base of register
* is at reg_base (0x1f0 primary, 0x170 secondary,
* if not changed by PCI configuration).
@@ -199,83 +132,29 @@ static u8 read_reg(int reg)
return ret;
}
-typedef struct pio_clocks_s {
- int address_time; /* Address setup (clocks) */
- int data_time; /* Active/data pulse (clocks) */
- int recovery_time; /* Recovery time (clocks) */
-} pio_clocks_t;
-
-static void compute_clocks(int pio, pio_clocks_t *clks)
-{
- if (pio != PIO_NOT_EXIST) {
- int adr_setup, data_pls;
- int bus_speed = ide_pci_clk ? ide_pci_clk : system_bus_clock();
-
- adr_setup = ide_pio_timings[pio].setup_time;
- data_pls = ide_pio_timings[pio].active_time;
- clks->address_time = cmpt_clk(adr_setup, bus_speed);
- clks->data_time = cmpt_clk(data_pls, bus_speed);
- clks->recovery_time = cmpt_clk(ide_pio_timings[pio].cycle_time
- - adr_setup-data_pls, bus_speed);
- if (clks->address_time < 1)
- clks->address_time = 1;
- if (clks->address_time > 4)
- clks->address_time = 4;
- if (clks->data_time < 1)
- clks->data_time = 1;
- if (clks->data_time > 16)
- clks->data_time = 16;
- if (clks->recovery_time < 2)
- clks->recovery_time = 2;
- if (clks->recovery_time > 17)
- clks->recovery_time = 17;
- } else {
- clks->address_time = 1;
- clks->data_time = 1;
- clks->recovery_time = 2;
- /* minimal values */
- }
-}
-
static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- /* primary and secondary drives share some registers,
- * so we have to program both drives
- */
+ ide_hwif_t *hwif = drive->hwif;
+ ide_drive_t *pair = ide_get_paired_drive(drive);
unsigned long flags;
- u8 pio1 = 0, pio2 = 0;
- pio_clocks_t first, second;
- int ax, drdy;
- u8 cycle1, cycle2, misc;
- ide_hwif_t *hwif = HWIF(drive);
-
- /* sets drive->drive_data for both drives */
- compute_pios(drive, pio);
- pio1 = hwif->drives[0].drive_data;
- pio2 = hwif->drives[1].drive_data;
-
- compute_clocks(pio1, &first);
- compute_clocks(pio2, &second);
-
- /* ax = max(a1,a2) */
- ax = (first.address_time < second.address_time) ? second.address_time : first.address_time;
-
- drdy = 2; /* DRDY is default 2 (by OPTi Databook) */
-
- cycle1 = ((first.data_time-1)<<4) | (first.recovery_time-2);
- cycle2 = ((second.data_time-1)<<4) | (second.recovery_time-2);
- misc = READ_PREFETCH | ((ax-1)<<4) | ((drdy-2)<<1);
-
-#ifdef OPTI621_DEBUG
- printk("%s: master: address: %d, data: %d, "
- "recovery: %d, drdy: %d [clk]\n",
- hwif->name, ax, first.data_time,
- first.recovery_time, drdy);
- printk("%s: slave: address: %d, data: %d, "
- "recovery: %d, drdy: %d [clk]\n",
- hwif->name, ax, second.data_time,
- second.recovery_time, drdy);
-#endif
+ u8 tim, misc, addr_pio = pio, clk;
+
+ /* DRDY is default 2 (by OPTi Databook) */
+ static const u8 addr_timings[2][5] = {
+ { 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */
+ { 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */
+ };
+ static const u8 data_rec_timings[2][5] = {
+ { 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */
+ { 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */
+ };
+
+ drive->drive_data = XFER_PIO_0 + pio;
+
+ if (pair->present) {
+ if (pair->drive_data && pair->drive_data < drive->drive_data)
+ addr_pio = pair->drive_data - XFER_PIO_0;
+ }
spin_lock_irqsave(&opti621_lock, flags);
@@ -289,24 +168,21 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
(void)inb(reg_base + CNTRL_REG);
/* if reads 0xc0, no interface exist? */
read_reg(CNTRL_REG);
- /* read version, probably 0 */
- read_reg(STRAP_REG);
- /* program primary drive */
- /* select Index-0 for Register-A */
- write_reg(0, MISC_REG);
- /* set read cycle timings */
- write_reg(cycle1, READ_REG);
- /* set write cycle timings */
- write_reg(cycle1, WRITE_REG);
+ /* check CLK speed */
+ clk = read_reg(STRAP_REG) & 1;
+
+ printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33);
- /* program secondary drive */
- /* select Index-1 for Register-B */
- write_reg(1, MISC_REG);
+ tim = data_rec_timings[clk][pio];
+ misc = addr_timings[clk][addr_pio];
+
+ /* select Index-0/1 for Register-A/B */
+ write_reg(drive->select.b.unit, MISC_REG);
/* set read cycle timings */
- write_reg(cycle2, READ_REG);
+ write_reg(tim, READ_REG);
/* set write cycle timings */
- write_reg(cycle2, WRITE_REG);
+ write_reg(tim, WRITE_REG);
/* use Register-A for drive 0 */
/* use Register-B for drive 1 */
@@ -319,45 +195,26 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
spin_unlock_irqrestore(&opti621_lock, flags);
}
-static void __devinit opti621_port_init_devs(ide_hwif_t *hwif)
-{
- hwif->drives[0].drive_data = PIO_DONT_KNOW;
- hwif->drives[1].drive_data = PIO_DONT_KNOW;
-}
-
static const struct ide_port_ops opti621_port_ops = {
- .port_init_devs = opti621_port_init_devs,
.set_pio_mode = opti621_set_pio_mode,
};
-static const struct ide_port_info opti621_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "OPTI621",
- .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
- .port_ops = &opti621_port_ops,
- .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
- .pio_mask = ATA_PIO3,
- .swdma_mask = ATA_SWDMA2,
- .mwdma_mask = ATA_MWDMA2,
- }, { /* 1 */
- .name = "OPTI621X",
- .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
- .port_ops = &opti621_port_ops,
- .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
- .pio_mask = ATA_PIO3,
- .swdma_mask = ATA_SWDMA2,
- .mwdma_mask = ATA_MWDMA2,
- }
+static const struct ide_port_info opti621_chipset __devinitdata = {
+ .name = "OPTI621/X",
+ .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
+ .port_ops = &opti621_port_ops,
+ .host_flags = IDE_HFLAG_NO_DMA,
+ .pio_mask = ATA_PIO4,
};
static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]);
+ return ide_setup_pci_device(dev, &opti621_chipset);
}
static const struct pci_device_id opti621_pci_tbl[] = {
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
- { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);
diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c
index 4b0b85d8faf..e127eb25ab6 100644
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -569,6 +569,11 @@ static int __devinit sis5513_init_one(struct pci_dev *dev, const struct pci_devi
{
struct ide_port_info d = sis5513_chipset;
u8 udma_rates[] = { 0x00, 0x00, 0x07, 0x1f, 0x3f, 0x3f, 0x7f, 0x7f };
+ int rc;
+
+ rc = pci_enable_device(dev);
+ if (rc)
+ return rc;
if (sis_find_family(dev) == 0)
return -ENOTSUPP;
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 02:55:21 +0000