diff options
Diffstat (limited to 'drivers/net/sfc/sfe4001.c')
| -rw-r--r-- | drivers/net/sfc/sfe4001.c | 225 |
1 files changed, 153 insertions, 72 deletions
diff --git a/drivers/net/sfc/sfe4001.c b/drivers/net/sfc/sfe4001.c index fe4e3fd2233..16b80acb999 100644 --- a/drivers/net/sfc/sfe4001.c +++ b/drivers/net/sfc/sfe4001.c @@ -1,6 +1,6 @@ /**************************************************************************** * Driver for Solarflare Solarstorm network controllers and boards - * Copyright 2007 Solarflare Communications Inc. + * Copyright 2007-2008 Solarflare Communications Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License version 2 as published @@ -8,10 +8,21 @@ */ /***************************************************************************** - * Support for the SFE4001 NIC: driver code for the PCA9539 I/O expander that - * controls the PHY power rails, and for the MAX6647 temp. sensor used to check - * the PHY + * Support for the SFE4001 and SFN4111T NICs. + * + * The SFE4001 does not power-up fully at reset due to its high power + * consumption. We control its power via a PCA9539 I/O expander. + * Both boards have a MAX6647 temperature monitor which we expose to + * the lm90 driver. + * + * This also provides minimal support for reflashing the PHY, which is + * initiated by resetting it with the FLASH_CFG_1 pin pulled down. + * On SFE4001 rev A2 and later this is connected to the 3V3X output of + * the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3. + * We represent reflash mode as PHY_MODE_SPECIAL and make it mutually + * exclusive with the network device being open. */ + #include <linux/delay.h> #include "net_driver.h" #include "efx.h" @@ -21,6 +32,7 @@ #include "falcon_hwdefs.h" #include "falcon_io.h" #include "mac.h" +#include "workarounds.h" /************************************************************************** * @@ -65,48 +77,9 @@ #define P1_SPARE_LBN 4 #define P1_SPARE_WIDTH 4 - -/************************************************************************** - * - * Temperature Sensor - * - **************************************************************************/ -#define MAX6647 0x4e - -#define RLTS 0x00 -#define RLTE 0x01 -#define RSL 0x02 -#define RCL 0x03 -#define RCRA 0x04 -#define RLHN 0x05 -#define RLLI 0x06 -#define RRHI 0x07 -#define RRLS 0x08 -#define WCRW 0x0a -#define WLHO 0x0b -#define WRHA 0x0c -#define WRLN 0x0e -#define OSHT 0x0f -#define REET 0x10 -#define RIET 0x11 -#define RWOE 0x19 -#define RWOI 0x20 -#define HYS 0x21 -#define QUEUE 0x22 -#define MFID 0xfe -#define REVID 0xff - -/* Status bits */ -#define MAX6647_BUSY (1 << 7) /* ADC is converting */ -#define MAX6647_LHIGH (1 << 6) /* Local high temp. alarm */ -#define MAX6647_LLOW (1 << 5) /* Local low temp. alarm */ -#define MAX6647_RHIGH (1 << 4) /* Remote high temp. alarm */ -#define MAX6647_RLOW (1 << 3) /* Remote low temp. alarm */ -#define MAX6647_FAULT (1 << 2) /* DXN/DXP short/open circuit */ -#define MAX6647_EOT (1 << 1) /* Remote junction overtemp. */ -#define MAX6647_IOT (1 << 0) /* Local junction overtemp. */ - -static const u8 xgphy_max_temperature = 90; +/* Temperature Sensor */ +#define MAX664X_REG_RSL 0x02 +#define MAX664X_REG_WLHO 0x0B static void sfe4001_poweroff(struct efx_nic *efx) { @@ -119,7 +92,7 @@ static void sfe4001_poweroff(struct efx_nic *efx) i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff); /* Clear any over-temperature alert */ - i2c_smbus_read_byte_data(hwmon_client, RSL); + i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL); } static int sfe4001_poweron(struct efx_nic *efx) @@ -131,7 +104,7 @@ static int sfe4001_poweron(struct efx_nic *efx) u8 out; /* Clear any previous over-temperature alert */ - rc = i2c_smbus_read_byte_data(hwmon_client, RSL); + rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL); if (rc < 0) return rc; @@ -209,10 +182,29 @@ fail_on: return rc; } -/* On SFE4001 rev A2 and later, we can control the FLASH_CFG_1 pin - * using the 3V3X output of the IO-expander. Allow the user to set - * this when the device is stopped, and keep it stopped then. - */ +static int sfn4111t_reset(struct efx_nic *efx) +{ + efx_oword_t reg; + + /* GPIO pins are also used for I2C, so block that temporarily */ + mutex_lock(&efx->i2c_adap.bus_lock); + + falcon_read(efx, ®, GPIO_CTL_REG_KER); + EFX_SET_OWORD_FIELD(reg, GPIO2_OEN, true); + EFX_SET_OWORD_FIELD(reg, GPIO2_OUT, false); + falcon_write(efx, ®, GPIO_CTL_REG_KER); + msleep(1000); + EFX_SET_OWORD_FIELD(reg, GPIO2_OUT, true); + EFX_SET_OWORD_FIELD(reg, GPIO3_OEN, true); + EFX_SET_OWORD_FIELD(reg, GPIO3_OUT, + !(efx->phy_mode & PHY_MODE_SPECIAL)); + falcon_write(efx, ®, GPIO_CTL_REG_KER); + + mutex_unlock(&efx->i2c_adap.bus_lock); + + ssleep(1); + return 0; +} static ssize_t show_phy_flash_cfg(struct device *dev, struct device_attribute *attr, char *buf) @@ -241,7 +233,10 @@ static ssize_t set_phy_flash_cfg(struct device *dev, err = -EBUSY; } else { efx->phy_mode = new_mode; - err = sfe4001_poweron(efx); + if (efx->board_info.type == EFX_BOARD_SFE4001) + err = sfe4001_poweron(efx); + else + err = sfn4111t_reset(efx); efx_reconfigure_port(efx); } rtnl_unlock(); @@ -261,35 +256,62 @@ static void sfe4001_fini(struct efx_nic *efx) i2c_unregister_device(efx->board_info.hwmon_client); } +static int sfe4001_check_hw(struct efx_nic *efx) +{ + s32 status; + + /* If XAUI link is up then do not monitor */ + if (EFX_WORKAROUND_7884(efx) && efx->mac_up) + return 0; + + /* Check the powered status of the PHY. Lack of power implies that + * the MAX6647 has shut down power to it, probably due to a temp. + * alarm. Reading the power status rather than the MAX6647 status + * directly because the later is read-to-clear and would thus + * start to power up the PHY again when polled, causing us to blip + * the power undesirably. + * We know we can read from the IO expander because we did + * it during power-on. Assume failure now is bad news. */ + status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN); + if (status >= 0 && + (status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0) + return 0; + + /* Use board power control, not PHY power control */ + sfe4001_poweroff(efx); + efx->phy_mode = PHY_MODE_OFF; + + return (status < 0) ? -EIO : -ERANGE; +} + +static struct i2c_board_info sfe4001_hwmon_info = { + I2C_BOARD_INFO("max6647", 0x4e), + .irq = -1, +}; + /* This board uses an I2C expander to provider power to the PHY, which needs to * be turned on before the PHY can be used. * Context: Process context, rtnl lock held */ int sfe4001_init(struct efx_nic *efx) { - struct i2c_client *hwmon_client; int rc; - hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647); - if (!hwmon_client) +#if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE) + efx->board_info.hwmon_client = + i2c_new_device(&efx->i2c_adap, &sfe4001_hwmon_info); +#else + efx->board_info.hwmon_client = + i2c_new_dummy(&efx->i2c_adap, sfe4001_hwmon_info.addr); +#endif + if (!efx->board_info.hwmon_client) return -EIO; - efx->board_info.hwmon_client = hwmon_client; - /* Set DSP over-temperature alert threshold */ - EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature); - rc = i2c_smbus_write_byte_data(hwmon_client, WLHO, - xgphy_max_temperature); + /* Raise board/PHY high limit from 85 to 90 degrees Celsius */ + rc = i2c_smbus_write_byte_data(efx->board_info.hwmon_client, + MAX664X_REG_WLHO, 90); if (rc) - goto fail_ioexp; - - /* Read it back and verify */ - rc = i2c_smbus_read_byte_data(hwmon_client, RLHN); - if (rc < 0) - goto fail_ioexp; - if (rc != xgphy_max_temperature) { - rc = -EFAULT; - goto fail_ioexp; - } + goto fail_hwmon; efx->board_info.ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539); if (!efx->board_info.ioexp_client) { @@ -301,6 +323,7 @@ int sfe4001_init(struct efx_nic *efx) * blink code. */ efx->board_info.blink = tenxpress_phy_blink; + efx->board_info.monitor = sfe4001_check_hw; efx->board_info.fini = sfe4001_fini; rc = sfe4001_poweron(efx); @@ -319,6 +342,64 @@ fail_on: fail_ioexp: i2c_unregister_device(efx->board_info.ioexp_client); fail_hwmon: - i2c_unregister_device(hwmon_client); + i2c_unregister_device(efx->board_info.hwmon_client); + return rc; +} + +static int sfn4111t_check_hw(struct efx_nic *efx) +{ + s32 status; + + /* If XAUI link is up then do not monitor */ + if (EFX_WORKAROUND_7884(efx) && efx->mac_up) + return 0; + + /* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */ + status = i2c_smbus_read_byte_data(efx->board_info.hwmon_client, + MAX664X_REG_RSL); + if (status < 0) + return -EIO; + if (status & 0x57) + return -ERANGE; + return 0; +} + +static void sfn4111t_fini(struct efx_nic *efx) +{ + EFX_INFO(efx, "%s\n", __func__); + + device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); + i2c_unregister_device(efx->board_info.hwmon_client); +} + +static struct i2c_board_info sfn4111t_hwmon_info = { + I2C_BOARD_INFO("max6647", 0x4e), + .irq = -1, +}; + +int sfn4111t_init(struct efx_nic *efx) +{ + int rc; + + efx->board_info.hwmon_client = + i2c_new_device(&efx->i2c_adap, &sfn4111t_hwmon_info); + if (!efx->board_info.hwmon_client) + return -EIO; + + efx->board_info.blink = tenxpress_phy_blink; + efx->board_info.monitor = sfn4111t_check_hw; + efx->board_info.fini = sfn4111t_fini; + + rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); + if (rc) + goto fail_hwmon; + + if (efx->phy_mode & PHY_MODE_SPECIAL) + sfn4111t_reset(efx); + + return 0; + +fail_hwmon: + i2c_unregister_device(efx->board_info.hwmon_client); return rc; } |