aboutsummaryrefslogtreecommitdiff
path: root/drivers/serial
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial')
-rw-r--r--drivers/serial/8250.c15
-rw-r--r--drivers/serial/8250_pci.c42
-rw-r--r--drivers/serial/Kconfig2
-rw-r--r--drivers/serial/atmel_serial.c4
-rw-r--r--drivers/serial/jsm/jsm_driver.c5
-rw-r--r--drivers/serial/jsm/jsm_tty.c6
-rw-r--r--drivers/serial/mcf.c11
-rw-r--r--drivers/serial/of_serial.c1
-rw-r--r--drivers/serial/sh-sci.h7
9 files changed, 89 insertions, 4 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 0d934bfbdd9..b4b39811b44 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -2083,6 +2083,20 @@ static int serial8250_startup(struct uart_port *port)
serial8250_set_mctrl(&up->port, up->port.mctrl);
+ /* Serial over Lan (SoL) hack:
+ Intel 8257x Gigabit ethernet chips have a
+ 16550 emulation, to be used for Serial Over Lan.
+ Those chips take a longer time than a normal
+ serial device to signalize that a transmission
+ data was queued. Due to that, the above test generally
+ fails. One solution would be to delay the reading of
+ iir. However, this is not reliable, since the timeout
+ is variable. So, let's just don't test if we receive
+ TX irq. This way, we'll never enable UART_BUG_TXEN.
+ */
+ if (up->port.flags & UPF_NO_TXEN_TEST)
+ goto dont_test_tx_en;
+
/*
* Do a quick test to see if we receive an
* interrupt when we enable the TX irq.
@@ -2102,6 +2116,7 @@ static int serial8250_startup(struct uart_port *port)
up->bugs &= ~UART_BUG_TXEN;
}
+dont_test_tx_en:
spin_unlock_irqrestore(&up->port.lock, flags);
/*
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 2a3671233b1..533f82025ad 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -798,6 +798,21 @@ pci_default_setup(struct serial_private *priv,
return setup_port(priv, port, bar, offset, board->reg_shift);
}
+static int skip_tx_en_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_port *port, int idx)
+{
+ port->flags |= UPF_NO_TXEN_TEST;
+ printk(KERN_DEBUG "serial8250: skipping TxEn test for device "
+ "[%04x:%04x] subsystem [%04x:%04x]\n",
+ priv->dev->vendor,
+ priv->dev->device,
+ priv->dev->subsystem_vendor,
+ priv->dev->subsystem_device);
+
+ return pci_default_setup(priv, board, port, idx);
+}
+
/* This should be in linux/pci_ids.h */
#define PCI_VENDOR_ID_SBSMODULARIO 0x124B
#define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B
@@ -806,6 +821,8 @@ pci_default_setup(struct serial_private *priv,
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
+#define PCI_VENDOR_ID_ADVANTECH 0x13fe
+#define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620
/* Unknown vendors/cards - this should not be in linux/pci_ids.h */
#define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584
@@ -862,6 +879,27 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.init = pci_inteli960ni_init,
.setup = pci_default_setup,
},
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_8257X_SOL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = skip_tx_en_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_82573L_SOL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = skip_tx_en_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_82573E_SOL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = skip_tx_en_setup,
+ },
/*
* ITE
*/
@@ -2152,6 +2190,10 @@ static int pciserial_resume_one(struct pci_dev *dev)
#endif
static struct pci_device_id serial_pci_tbl[] = {
+ /* Advantech use PCI_DEVICE_ID_ADVANTECH_PCI3620 (0x3620) as 'PCI_SUBVENDOR_ID' */
+ { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620,
+ PCI_DEVICE_ID_ADVANTECH_PCI3620, 0x0001, 0, 0,
+ pbn_b2_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 3e525e38a5d..7d7f576da20 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -982,7 +982,7 @@ config SERIAL_SH_SCI_CONSOLE
config SERIAL_PNX8XXX
bool "Enable PNX8XXX SoCs' UART Support"
- depends on MIPS && SOC_PNX8550
+ depends on MIPS && (SOC_PNX8550 || SOC_PNX833X)
select SERIAL_CORE
help
If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 89362d733d6..8f58f7ff0dd 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -877,6 +877,10 @@ static int atmel_startup(struct uart_port *port)
}
}
+ /* Save current CSR for comparison in atmel_tasklet_func() */
+ atmel_port->irq_status_prev = UART_GET_CSR(port);
+ atmel_port->irq_status = atmel_port->irq_status_prev;
+
/*
* Finally, enable the serial port
*/
diff --git a/drivers/serial/jsm/jsm_driver.c b/drivers/serial/jsm/jsm_driver.c
index 338cf8a08b4..ac79cbe4c2c 100644
--- a/drivers/serial/jsm/jsm_driver.c
+++ b/drivers/serial/jsm/jsm_driver.c
@@ -84,6 +84,8 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
brd->pci_dev = pdev;
if (pdev->device == PCIE_DEVICE_ID_NEO_4_IBM)
brd->maxports = 4;
+ else if (pdev->device == PCI_DEVICE_ID_DIGI_NEO_8)
+ brd->maxports = 8;
else
brd->maxports = 2;
@@ -180,7 +182,7 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
return rc;
}
-static void jsm_remove_one(struct pci_dev *pdev)
+static void __devexit jsm_remove_one(struct pci_dev *pdev)
{
struct jsm_board *brd = pci_get_drvdata(pdev);
int i = 0;
@@ -212,6 +214,7 @@ static struct pci_device_id jsm_pci_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45), 0, 0, 2 },
{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45PRI), 0, 0, 3 },
{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_4_IBM), 0, 0, 4 },
+ { PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_DIGI_NEO_8), 0, 0, 5 },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, jsm_pci_tbl);
diff --git a/drivers/serial/jsm/jsm_tty.c b/drivers/serial/jsm/jsm_tty.c
index 3547558d2ca..324c74d2f66 100644
--- a/drivers/serial/jsm/jsm_tty.c
+++ b/drivers/serial/jsm/jsm_tty.c
@@ -161,6 +161,11 @@ static void jsm_tty_stop_rx(struct uart_port *port)
channel->ch_bd->bd_ops->disable_receiver(channel);
}
+static void jsm_tty_enable_ms(struct uart_port *port)
+{
+ /* Nothing needed */
+}
+
static void jsm_tty_break(struct uart_port *port, int break_state)
{
unsigned long lock_flags;
@@ -345,6 +350,7 @@ static struct uart_ops jsm_ops = {
.start_tx = jsm_tty_start_tx,
.send_xchar = jsm_tty_send_xchar,
.stop_rx = jsm_tty_stop_rx,
+ .enable_ms = jsm_tty_enable_ms,
.break_ctl = jsm_tty_break,
.startup = jsm_tty_open,
.shutdown = jsm_tty_close,
diff --git a/drivers/serial/mcf.c b/drivers/serial/mcf.c
index b2001c5b145..56841fe5f48 100644
--- a/drivers/serial/mcf.c
+++ b/drivers/serial/mcf.c
@@ -212,10 +212,18 @@ static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
{
unsigned long flags;
unsigned int baud, baudclk;
+#if defined(CONFIG_M5272)
+ unsigned int baudfr;
+#endif
unsigned char mr1, mr2;
baud = uart_get_baud_rate(port, termios, old, 0, 230400);
+#if defined(CONFIG_M5272)
+ baudclk = (MCF_BUSCLK / baud) / 32;
+ baudfr = (((MCF_BUSCLK / baud) + 1) / 2) % 16;
+#else
baudclk = ((MCF_BUSCLK / baud) + 16) / 32;
+#endif
mr1 = MCFUART_MR1_RXIRQRDY | MCFUART_MR1_RXERRCHAR;
mr2 = 0;
@@ -262,6 +270,9 @@ static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
writeb(mr2, port->membase + MCFUART_UMR);
writeb((baudclk & 0xff00) >> 8, port->membase + MCFUART_UBG1);
writeb((baudclk & 0xff), port->membase + MCFUART_UBG2);
+#if defined(CONFIG_M5272)
+ writeb((baudfr & 0x0f), port->membase + MCFUART_UFPD);
+#endif
writeb(MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER,
port->membase + MCFUART_UCSR);
writeb(MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE,
diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c
index a821e3a3d66..14f8fa9135b 100644
--- a/drivers/serial/of_serial.c
+++ b/drivers/serial/of_serial.c
@@ -163,6 +163,7 @@ static struct of_device_id __devinitdata of_platform_serial_table[] = {
{ .type = "serial", .compatible = "ns16450", .data = (void *)PORT_16450, },
{ .type = "serial", .compatible = "ns16550", .data = (void *)PORT_16550, },
{ .type = "serial", .compatible = "ns16750", .data = (void *)PORT_16750, },
+ { .type = "serial", .compatible = "ns16850", .data = (void *)PORT_16850, },
#ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
{ .type = "serial", .compatible = "ibm,qpace-nwp-serial",
.data = (void *)PORT_NWPSERIAL, },
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index 38c600c0dbb..022e89ffec1 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -32,7 +32,9 @@
#elif defined(CONFIG_CPU_SUBTYPE_SH7720) || \
defined(CONFIG_CPU_SUBTYPE_SH7721)
# define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
-#define SCIF_ORER 0x0200 /* overrun error bit */
+# define PORT_PTCR 0xA405011EUL
+# define PORT_PVCR 0xA4050122UL
+# define SCIF_ORER 0x0200 /* overrun error bit */
#elif defined(CONFIG_SH_RTS7751R2D)
# define SCSPTR1 0xFFE0001C /* 8 bit SCIF */
# define SCSPTR2 0xFFE80020 /* 16 bit SCIF */
@@ -131,7 +133,7 @@
# define SCSPTR3 0xffed0024 /* 16 bit SCIF */
# define SCSPTR4 0xffee0024 /* 16 bit SCIF */
# define SCSPTR5 0xffef0024 /* 16 bit SCIF */
-# define SCIF_OPER 0x0001 /* Overrun error bit */
+# define SCIF_ORER 0x0001 /* Overrun error bit */
# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
#elif defined(CONFIG_CPU_SUBTYPE_SH7201) || \
defined(CONFIG_CPU_SUBTYPE_SH7203) || \
@@ -393,6 +395,7 @@ SCIx_FNS(SCSCR, 0x08, 16, 0x08, 16)
SCIx_FNS(SCxTDR, 0x20, 8, 0x0c, 8)
SCIx_FNS(SCxSR, 0x14, 16, 0x10, 16)
SCIx_FNS(SCxRDR, 0x24, 8, 0x14, 8)
+SCIx_FNS(SCSPTR, 0, 0, 0, 0)
SCIF_FNS(SCTDSR, 0x0c, 8)
SCIF_FNS(SCFER, 0x10, 16)
SCIF_FNS(SCFCR, 0x18, 16)
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-27 10:35:09 +0000