diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/net/e1000/e1000_hw.c | 174 | ||||
-rw-r--r-- | drivers/net/e1000/e1000_hw.h | 2 |
2 files changed, 2 insertions, 174 deletions
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index 74aa5997331..765fd71ad5f 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -33,9 +33,6 @@ #include "e1000_hw.h" -static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask); -static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask); - static s32 e1000_check_downshift(struct e1000_hw *hw); static s32 e1000_check_polarity(struct e1000_hw *hw, e1000_rev_polarity *polarity); @@ -48,7 +45,6 @@ static s32 e1000_detect_gig_phy(struct e1000_hw *hw); static s32 e1000_get_auto_rd_done(struct e1000_hw *hw); static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length, u16 *max_length); -static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw); static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw); static s32 e1000_id_led_init(struct e1000_hw *hw); static void e1000_init_rx_addrs(struct e1000_hw *hw); @@ -61,7 +57,6 @@ static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words, static s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd); static s32 e1000_phy_m88_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); -static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active); static s32 e1000_wait_autoneg(struct e1000_hw *hw); static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value); @@ -2607,70 +2602,6 @@ static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw) return data; } -static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask) -{ - u32 swfw_sync = 0; - u32 swmask = mask; - u32 fwmask = mask << 16; - s32 timeout = 200; - - DEBUGFUNC("e1000_swfw_sync_acquire"); - - if (!hw->swfw_sync_present) - return e1000_get_hw_eeprom_semaphore(hw); - - while (timeout) { - if (e1000_get_hw_eeprom_semaphore(hw)) - return -E1000_ERR_SWFW_SYNC; - - swfw_sync = er32(SW_FW_SYNC); - if (!(swfw_sync & (fwmask | swmask))) { - break; - } - - /* firmware currently using resource (fwmask) */ - /* or other software thread currently using resource (swmask) */ - e1000_put_hw_eeprom_semaphore(hw); - mdelay(5); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); - return -E1000_ERR_SWFW_SYNC; - } - - swfw_sync |= swmask; - ew32(SW_FW_SYNC, swfw_sync); - - e1000_put_hw_eeprom_semaphore(hw); - return E1000_SUCCESS; -} - -static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask) -{ - u32 swfw_sync; - u32 swmask = mask; - - DEBUGFUNC("e1000_swfw_sync_release"); - - if (!hw->swfw_sync_present) { - e1000_put_hw_eeprom_semaphore(hw); - return; - } - - /* if (e1000_get_hw_eeprom_semaphore(hw)) - * return -E1000_ERR_SWFW_SYNC; */ - while (e1000_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS); - /* empty */ - - swfw_sync = er32(SW_FW_SYNC); - swfw_sync &= ~swmask; - ew32(SW_FW_SYNC, swfw_sync); - - e1000_put_hw_eeprom_semaphore(hw); -} - /***************************************************************************** * Reads the value from a PHY register, if the value is on a specific non zero * page, sets the page first. @@ -2680,28 +2611,19 @@ static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask) s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data) { u32 ret_val; - u16 swfw; DEBUGFUNC("e1000_read_phy_reg"); - swfw = E1000_SWFW_PHY0_SM; - if (e1000_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - if ((hw->phy_type == e1000_phy_igp) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, (u16)reg_addr); - if (ret_val) { - e1000_swfw_sync_release(hw, swfw); + if (ret_val) return ret_val; - } } ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, phy_data); - - e1000_swfw_sync_release(hw, swfw); return ret_val; } @@ -2787,28 +2709,20 @@ static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 phy_data) { u32 ret_val; - u16 swfw; DEBUGFUNC("e1000_write_phy_reg"); - swfw = E1000_SWFW_PHY0_SM; - if (e1000_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - if ((hw->phy_type == e1000_phy_igp) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, (u16)reg_addr); - if (ret_val) { - e1000_swfw_sync_release(hw, swfw); + if (ret_val) return ret_val; - } } ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, phy_data); - e1000_swfw_sync_release(hw, swfw); return ret_val; } @@ -2883,18 +2797,12 @@ s32 e1000_phy_hw_reset(struct e1000_hw *hw) u32 ctrl, ctrl_ext; u32 led_ctrl; s32 ret_val; - u16 swfw; DEBUGFUNC("e1000_phy_hw_reset"); DEBUGOUT("Resetting Phy...\n"); if (hw->mac_type > e1000_82543) { - swfw = E1000_SWFW_PHY0_SM; - if (e1000_swfw_sync_acquire(hw, swfw)) { - DEBUGOUT("Unable to acquire swfw sync\n"); - return -E1000_ERR_SWFW_SYNC; - } /* Read the device control register and assert the E1000_CTRL_PHY_RST * bit. Then, take it out of reset. * For e1000 hardware, we delay for 10ms between the assert @@ -2908,8 +2816,6 @@ s32 e1000_phy_hw_reset(struct e1000_hw *hw) ew32(CTRL, ctrl); E1000_WRITE_FLUSH(); - - e1000_swfw_sync_release(hw, swfw); } else { /* Read the Extended Device Control Register, assert the PHY_RESET_DIR * bit to put the PHY into reset. Then, take it out of reset. @@ -3515,8 +3421,6 @@ static s32 e1000_acquire_eeprom(struct e1000_hw *hw) DEBUGFUNC("e1000_acquire_eeprom"); - if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) - return -E1000_ERR_SWFW_SYNC; eecd = er32(EECD); /* Request EEPROM Access */ @@ -3534,7 +3438,6 @@ static s32 e1000_acquire_eeprom(struct e1000_hw *hw) eecd &= ~E1000_EECD_REQ; ew32(EECD, eecd); DEBUGOUT("Could not acquire EEPROM grant\n"); - e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); return -E1000_ERR_EEPROM; } } @@ -3653,8 +3556,6 @@ static void e1000_release_eeprom(struct e1000_hw *hw) eecd &= ~E1000_EECD_REQ; ew32(EECD, eecd); } - - e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); } /****************************************************************************** @@ -3847,8 +3748,6 @@ static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words, u32 i = 0; s32 error = 0; - if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) - return -E1000_ERR_SWFW_SYNC; for (i = 0; i < words; i++) { register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | @@ -3869,7 +3768,6 @@ static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words, } } - e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); return error; } @@ -5681,71 +5579,3 @@ static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw) mdelay(10); return E1000_SUCCESS; } - -/*************************************************************************** - * - * Using the combination of SMBI and SWESMBI semaphore bits when resetting - * adapter or Eeprom access. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_EEPROM if fail to access EEPROM. - * E1000_SUCCESS at any other case. - * - ***************************************************************************/ -static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) -{ - s32 timeout; - u32 swsm; - - DEBUGFUNC("e1000_get_hw_eeprom_semaphore"); - - if (!hw->eeprom_semaphore_present) - return E1000_SUCCESS; - - /* Get the FW semaphore. */ - timeout = hw->eeprom.word_size + 1; - while (timeout) { - swsm = er32(SWSM); - swsm |= E1000_SWSM_SWESMBI; - ew32(SWSM, swsm); - /* if we managed to set the bit we got the semaphore. */ - swsm = er32(SWSM); - if (swsm & E1000_SWSM_SWESMBI) - break; - - udelay(50); - timeout--; - } - - if (!timeout) { - /* Release semaphores */ - e1000_put_hw_eeprom_semaphore(hw); - DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n"); - return -E1000_ERR_EEPROM; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * This function clears HW semaphore bits. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - None. - * - ***************************************************************************/ -static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) -{ - u32 swsm; - - DEBUGFUNC("e1000_put_hw_eeprom_semaphore"); - - if (!hw->eeprom_semaphore_present) - return; - - swsm = er32(SWSM); - swsm &= ~(E1000_SWSM_SWESMBI); - ew32(SWSM, swsm); -} diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index 243dad25bcc..1a8a0006f3e 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -284,7 +284,6 @@ typedef enum { #define E1000_ERR_MASTER_REQUESTS_PENDING 10 #define E1000_ERR_HOST_INTERFACE_COMMAND 11 #define E1000_BLK_PHY_RESET 12 -#define E1000_ERR_SWFW_SYNC 13 #define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \ (((_value) & 0xff00) >> 8)) @@ -1327,7 +1326,6 @@ struct e1000_hw { e1000_ffe_config ffe_config_state; u32 asf_firmware_present; u32 eeprom_semaphore_present; - u32 swfw_sync_present; unsigned long io_base; u32 phy_id; u32 phy_revision; |