diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/usb/core/hcd.h | 1 | ||||
| -rw-r--r-- | drivers/usb/host/pci-quirks.c | 123 | ||||
| -rw-r--r-- | drivers/usb/host/xhci-hcd.c | 377 | ||||
| -rw-r--r-- | drivers/usb/host/xhci-mem.c | 75 | ||||
| -rw-r--r-- | drivers/usb/host/xhci-pci.c | 150 | ||||
| -rw-r--r-- | drivers/usb/host/xhci.h | 63 |
6 files changed, 787 insertions, 2 deletions
diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h index 174170f14f0..7a47498b0aa 100644 --- a/drivers/usb/core/hcd.h +++ b/drivers/usb/core/hcd.h @@ -173,6 +173,7 @@ struct hc_driver { #define HCD_LOCAL_MEM 0x0002 /* HC needs local memory */ #define HCD_USB11 0x0010 /* USB 1.1 */ #define HCD_USB2 0x0020 /* USB 2.0 */ +#define HCD_USB3 0x0040 /* USB 3.0 */ /* called to init HCD and root hub */ int (*reset) (struct usb_hcd *hcd); diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index 033c2846ce5..83b5f9cea85 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -15,6 +15,7 @@ #include <linux/delay.h> #include <linux/acpi.h> #include "pci-quirks.h" +#include "xhci-ext-caps.h" #define UHCI_USBLEGSUP 0xc0 /* legacy support */ @@ -341,7 +342,127 @@ static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev) return; } +/* + * handshake - spin reading a register until handshake completes + * @ptr: address of hc register to be read + * @mask: bits to look at in result of read + * @done: value of those bits when handshake succeeds + * @wait_usec: timeout in microseconds + * @delay_usec: delay in microseconds to wait between polling + * + * Polls a register every delay_usec microseconds. + * Returns 0 when the mask bits have the value done. + * Returns -ETIMEDOUT if this condition is not true after + * wait_usec microseconds have passed. + */ +static int handshake(void __iomem *ptr, u32 mask, u32 done, + int wait_usec, int delay_usec) +{ + u32 result; + + do { + result = readl(ptr); + result &= mask; + if (result == done) + return 0; + udelay(delay_usec); + wait_usec -= delay_usec; + } while (wait_usec > 0); + return -ETIMEDOUT; +} + +/** + * PCI Quirks for xHCI. + * + * Takes care of the handoff between the Pre-OS (i.e. BIOS) and the OS. + * It signals to the BIOS that the OS wants control of the host controller, + * and then waits 5 seconds for the BIOS to hand over control. + * If we timeout, assume the BIOS is broken and take control anyway. + */ +static void __devinit quirk_usb_handoff_xhci(struct pci_dev *pdev) +{ + void __iomem *base; + int ext_cap_offset; + void __iomem *op_reg_base; + u32 val; + int timeout; + + if (!mmio_resource_enabled(pdev, 0)) + return; + + base = ioremap_nocache(pci_resource_start(pdev, 0), + pci_resource_len(pdev, 0)); + if (base == NULL) + return; + /* + * Find the Legacy Support Capability register - + * this is optional for xHCI host controllers. + */ + ext_cap_offset = xhci_find_next_cap_offset(base, XHCI_HCC_PARAMS_OFFSET); + do { + if (!ext_cap_offset) + /* We've reached the end of the extended capabilities */ + goto hc_init; + val = readl(base + ext_cap_offset); + if (XHCI_EXT_CAPS_ID(val) == XHCI_EXT_CAPS_LEGACY) + break; + ext_cap_offset = xhci_find_next_cap_offset(base, ext_cap_offset); + } while (1); + + /* If the BIOS owns the HC, signal that the OS wants it, and wait */ + if (val & XHCI_HC_BIOS_OWNED) { + writel(val & XHCI_HC_OS_OWNED, base + ext_cap_offset); + + /* Wait for 5 seconds with 10 microsecond polling interval */ + timeout = handshake(base + ext_cap_offset, XHCI_HC_BIOS_OWNED, + 0, 5000, 10); + + /* Assume a buggy BIOS and take HC ownership anyway */ + if (timeout) { + dev_warn(&pdev->dev, "xHCI BIOS handoff failed" + " (BIOS bug ?) %08x\n", val); + writel(val & ~XHCI_HC_BIOS_OWNED, base + ext_cap_offset); + } + } + + /* Disable any BIOS SMIs */ + writel(XHCI_LEGACY_DISABLE_SMI, + base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET); + +hc_init: + op_reg_base = base + XHCI_HC_LENGTH(readl(base)); + + /* Wait for the host controller to be ready before writing any + * operational or runtime registers. Wait 5 seconds and no more. + */ + timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_CNR, 0, + 5000, 10); + /* Assume a buggy HC and start HC initialization anyway */ + if (timeout) { + val = readl(op_reg_base + XHCI_STS_OFFSET); + dev_warn(&pdev->dev, + "xHCI HW not ready after 5 sec (HC bug?) " + "status = 0x%x\n", val); + } + + /* Send the halt and disable interrupts command */ + val = readl(op_reg_base + XHCI_CMD_OFFSET); + val &= ~(XHCI_CMD_RUN | XHCI_IRQS); + writel(val, op_reg_base + XHCI_CMD_OFFSET); + + /* Wait for the HC to halt - poll every 125 usec (one microframe). */ + timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_HALT, 1, + XHCI_MAX_HALT_USEC, 125); + if (timeout) { + val = readl(op_reg_base + XHCI_STS_OFFSET); + dev_warn(&pdev->dev, + "xHCI HW did not halt within %d usec " + "status = 0x%x\n", XHCI_MAX_HALT_USEC, val); + } + + iounmap(base); +} static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev) { @@ -351,5 +472,7 @@ static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev) quirk_usb_handoff_ohci(pdev); else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI) quirk_usb_disable_ehci(pdev); + else if (pdev->class == PCI_CLASS_SERIAL_USB_XHCI) + quirk_usb_handoff_xhci(pdev); } DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff); diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c new file mode 100644 index 00000000000..64fcc22e9d5 --- /dev/null +++ b/drivers/usb/host/xhci-hcd.c @@ -0,0 +1,377 @@ +/* + * xHCI host controller driver + * + * Copyright (C) 2008 Intel Corp. + * + * Author: Sarah Sharp + * Some code borrowed from the Linux EHCI driver. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY + * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software Foundation, + * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/irq.h> +#include <linux/module.h> + +#include "xhci.h" + +#define DRIVER_AUTHOR "Sarah Sharp" +#define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver" + +/* TODO: copied from ehci-hcd.c - can this be refactored? */ +/* + * handshake - spin reading hc until handshake completes or fails + * @ptr: address of hc register to be read + * @mask: bits to look at in result of read + * @done: value of those bits when handshake succeeds + * @usec: timeout in microseconds + * + * Returns negative errno, or zero on success + * + * Success happens when the "mask" bits have the specified value (hardware + * handshake done). There are two failure modes: "usec" have passed (major + * hardware flakeout), or the register reads as all-ones (hardware removed). + */ +static int handshake(struct xhci_hcd *xhci, void __iomem *ptr, + u32 mask, u32 done, int usec) +{ + u32 result; + + do { + result = xhci_readl(xhci, ptr); + if (result == ~(u32)0) /* card removed */ + return -ENODEV; + result &= mask; + if (result == done) + return 0; + udelay(1); + usec--; + } while (usec > 0); + return -ETIMEDOUT; +} + +/* + * Force HC into halt state. + * + * Disable any IRQs and clear the run/stop bit. + * HC will complete any current and actively pipelined transactions, and + * should halt within 16 microframes of the run/stop bit being cleared. + * Read HC Halted bit in the status register to see when the HC is finished. + * XXX: shouldn't we set HC_STATE_HALT here somewhere? + */ +int xhci_halt(struct xhci_hcd *xhci) +{ + u32 halted; + u32 cmd; + u32 mask; + + xhci_dbg(xhci, "// Halt the HC\n"); + /* Disable all interrupts from the host controller */ + mask = ~(XHCI_IRQS); + halted = xhci_readl(xhci, &xhci->op_regs->status) & STS_HALT; + if (!halted) + mask &= ~CMD_RUN; + + cmd = xhci_readl(xhci, &xhci->op_regs->command); + cmd &= mask; + xhci_writel(xhci, cmd, &xhci->op_regs->command); + + return handshake(xhci, &xhci->op_regs->status, + STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC); +} + +/* + * Reset a halted HC, and set the internal HC state to HC_STATE_HALT. + * + * This resets pipelines, timers, counters, state machines, etc. + * Transactions will be terminated immediately, and operational registers + * will be set to their defaults. + */ +int xhci_reset(struct xhci_hcd *xhci) +{ + u32 command; + u32 state; + + state = xhci_readl(xhci, &xhci->op_regs->status); + BUG_ON((state & STS_HALT) == 0); + + xhci_dbg(xhci, "// Reset the HC\n"); + command = xhci_readl(xhci, &xhci->op_regs->command); + command |= CMD_RESET; + xhci_writel(xhci, command, &xhci->op_regs->command); + /* XXX: Why does EHCI set this here? Shouldn't other code do this? */ + xhci_to_hcd(xhci)->state = HC_STATE_HALT; + + return handshake(xhci, &xhci->op_regs->command, CMD_RESET, 0, 250 * 1000); +} + +/* + * Stop the HC from processing the endpoint queues. + */ +static void xhci_quiesce(struct xhci_hcd *xhci) +{ + /* + * Queues are per endpoint, so we need to disable an endpoint or slot. + * + * To disable a slot, we need to insert a disable slot command on the + * command ring and ring the doorbell. This will also free any internal + * resources associated with the slot (which might not be what we want). + * + * A Release Endpoint command sounds better - doesn't free internal HC + * memory, but removes the endpoints from the schedule and releases the + * bandwidth, disables the doorbells, and clears the endpoint enable + * flag. Usually used prior to a set interface command. + * + * TODO: Implement after command ring code is done. + */ + BUG_ON(!HC_IS_RUNNING(xhci_to_hcd(xhci)->state)); + xhci_dbg(xhci, "Finished quiescing -- code not written yet\n"); +} + +#if 0 +/* Set up MSI-X table for entry 0 (may claim other entries later) */ +static int xhci_setup_msix(struct xhci_hcd *xhci) +{ + int ret; + struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + + xhci->msix_count = 0; + /* XXX: did I do this right? ixgbe does kcalloc for more than one */ + xhci->msix_entries = kmalloc(sizeof(struct msix_entry), GFP_KERNEL); + if (!xhci->msix_entries) { + xhci_err(xhci, "Failed to allocate MSI-X entries\n"); + return -ENOMEM; + } + xhci->msix_entries[0].entry = 0; + + ret = pci_enable_msix(pdev, xhci->msix_entries, xhci->msix_count); + if (ret) { + xhci_err(xhci, "Failed to enable MSI-X\n"); + goto free_entries; + } + + /* + * Pass the xhci pointer value as the request_irq "cookie". + * If more irqs are added, this will need to be unique for each one. + */ + ret = request_irq(xhci->msix_entries[0].vector, &xhci_irq, 0, + "xHCI", xhci_to_hcd(xhci)); + if (ret) { + xhci_err(xhci, "Failed to allocate MSI-X interrupt\n"); + goto disable_msix; + } + xhci_dbg(xhci, "Finished setting up MSI-X\n"); + return 0; + +disable_msix: + pci_disable_msix(pdev); +free_entries: + kfree(xhci->msix_entries); + xhci->msix_entries = NULL; + return ret; +} + +/* XXX: code duplication; can xhci_setup_msix call this? */ +/* Free any IRQs and disable MSI-X */ +static void xhci_cleanup_msix(struct xhci_hcd *xhci) +{ + struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + if (!xhci->msix_entries) + return; + + free_irq(xhci->msix_entries[0].vector, xhci); + pci_disable_msix(pdev); + kfree(xhci->msix_entries); + xhci->msix_entries = NULL; + xhci_dbg(xhci, "Finished cleaning up MSI-X\n"); +} +#endif + +/* + * Initialize memory for HCD and xHC (one-time init). + * + * Program the PAGESIZE register, initialize the device context array, create + * device contexts (?), set up a command ring segment (or two?), create event + * ring (one for now). + */ +int xhci_init(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + int retval = 0; + + xhci_dbg(xhci, "xhci_init\n"); + spin_lock_init(&xhci->lock); + retval = xhci_mem_init(xhci, GFP_KERNEL); + xhci_dbg(xhci, "Finished xhci_init\n"); + + return retval; +} + +/* + * Start the HC after it was halted. + * + * This function is called by the USB core when the HC driver is added. + * Its opposite is xhci_stop(). + * + * xhci_init() must be called once before this function can be called. + * Reset the HC, enable device slot contexts, program DCBAAP, and + * set command ring pointer and event ring pointer. + * + * Setup MSI-X vectors and enable interrupts. + */ +int xhci_run(struct usb_hcd *hcd) +{ + u32 temp; + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + xhci_dbg(xhci, "xhci_run\n"); + +#if 0 /* FIXME: MSI not setup yet */ + /* Do this at the very last minute */ + ret = xhci_setup_msix(xhci); + if (!ret) + return ret; + + return -ENOSYS; +#endif + xhci_dbg(xhci, "// Set the interrupt modulation register\n"); + temp = xhci_readl(xhci, &xhci->ir_set->irq_control); + temp &= 0xffff; + temp |= (u32) 160; + xhci_writel(xhci, temp, &xhci->ir_set->irq_control); + + /* Set the HCD state before we enable the irqs */ + hcd->state = HC_STATE_RUNNING; + temp = xhci_readl(xhci, &xhci->op_regs->command); + temp |= (CMD_EIE); + xhci_dbg(xhci, "// Enable interrupts, cmd = 0x%x.\n", + temp); + xhci_writel(xhci, temp, &xhci->op_regs->command); + + temp = xhci_readl(xhci, &xhci->ir_set->irq_pending); + xhci_dbg(xhci, "// Enabling event ring interrupter 0x%x" + " by writing 0x%x to irq_pending\n", + (unsigned int) xhci->ir_set, + (unsigned int) ER_IRQ_ENABLE(temp)); + xhci_writel(xhci, ER_IRQ_ENABLE(temp), + &xhci->ir_set->irq_pending); + xhci_print_ir_set(xhci, xhci->ir_set, 0); + + temp = xhci_readl(xhci, &xhci->op_regs->command); + temp |= (CMD_RUN); + xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n", + temp); + xhci_writel(xhci, temp, &xhci->op_regs->command); + /* Flush PCI posted writes */ + temp = xhci_readl(xhci, &xhci->op_regs->command); + xhci_dbg(xhci, "// @%x = 0x%x\n", + (unsigned int) &xhci->op_regs->command, temp); + + xhci_dbg(xhci, "Finished xhci_run\n"); + return 0; +} + +/* + * Stop xHCI driver. + * + * This function is called by the USB core when the HC driver is removed. + * Its opposite is xhci_run(). + * + * Disable device contexts, disable IRQs, and quiesce the HC. + * Reset the HC, finish any completed transactions, and cleanup memory. + */ +void xhci_stop(struct usb_hcd *hcd) +{ + u32 temp; + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + + spin_lock_irq(&xhci->lock); + if (HC_IS_RUNNING(hcd->state)) + xhci_quiesce(xhci); + xhci_halt(xhci); + xhci_reset(xhci); + spin_unlock_irq(&xhci->lock); + +#if 0 /* No MSI yet */ + xhci_cleanup_msix(xhci); +#endif + xhci_dbg(xhci, "// Disabling event ring interrupts\n"); + temp = xhci_readl(xhci, &xhci->op_regs->status); + xhci_writel(xhci, temp & ~STS_EINT, &xhci->op_regs->status); + temp = xhci_readl(xhci, &xhci->ir_set->irq_pending); + xhci_writel(xhci, ER_IRQ_DISABLE(temp), + &xhci->ir_set->irq_pending); + xhci_print_ir_set(xhci, xhci->ir_set, 0); + + xhci_dbg(xhci, "cleaning up memory\n"); + xhci_mem_cleanup(xhci); + xhci_dbg(xhci, "xhci_stop completed - status = %x\n", + xhci_readl(xhci, &xhci->op_regs->status)); +} + +/* + * Shutdown HC (not bus-specific) + * + * This is called when the machine is rebooting or halting. We assume that the + * machine will be powered off, and the HC's internal state will be reset. + * Don't bother to free memory. + */ +void xhci_shutdown(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + + spin_lock_irq(&xhci->lock); + xhci_halt(xhci); + spin_unlock_irq(&xhci->lock); + +#if 0 + xhci_cleanup_msix(xhci); +#endif + + xhci_dbg(xhci, "xhci_shutdown completed - status = %x\n", + xhci_readl(xhci, &xhci->op_regs->status)); +} + +int xhci_get_frame(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + /* EHCI mods by the periodic size. Why? */ + return xhci_readl(xhci, &xhci->run_regs->microframe_index) >> 3; +} + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_LICENSE("GPL"); + +static int __init xhci_hcd_init(void) +{ +#ifdef CONFIG_PCI + int retval = 0; + + retval = xhci_register_pci(); + + if (retval < 0) { + printk(KERN_DEBUG "Problem registering PCI driver."); + return retval; + } +#endif + return 0; +} +module_init(xhci_hcd_init); + +static void __exit xhci_hcd_cleanup(void) +{ +#ifdef CONFIG_PCI + xhci_unregister_pci(); +#endif +} +module_exit(xhci_hcd_cleanup); diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c new file mode 100644 index 00000000000..0e383f9c380 --- /dev/null +++ b/drivers/usb/host/xhci-mem.c @@ -0,0 +1,75 @@ +/* + * xHCI host controller driver + * + * Copyright (C) 2008 Intel Corp. + * + * Author: Sarah Sharp + * Some code borrowed from the Linux EHCI driver. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY + * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software Foundation, + * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/usb.h> + +#include "xhci.h" + +void xhci_mem_cleanup(struct xhci_hcd *xhci) +{ + xhci->page_size = 0; + xhci->page_shift = 0; +} + +int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) +{ + unsigned int val, val2; + u32 page_size; + int i; + + page_size = xhci_readl(xhci, &xhci->op_regs->page_size); + xhci_dbg(xhci, "Supported page size register = 0x%x\n", page_size); + for (i = 0; i < 16; i++) { + if ((0x1 & page_size) != 0) + break; + page_size = page_size >> 1; + } + if (i < 16) + xhci_dbg(xhci, "Supported page size of %iK\n", (1 << (i+12)) / 1024); + else + xhci_warn(xhci, "WARN: no supported page size\n"); + /* Use 4K pages, since that's common and the minimum the HC supports */ + xhci->page_shift = 12; + xhci->page_size = 1 << xhci->page_shift; + xhci_dbg(xhci, "HCD page size set to %iK\n", xhci->page_size / 1024); + + /* + * Program the Number of Device Slots Enabled field in the CONFIG + * register with the max value of slots the HC can handle. + */ + val = HCS_MAX_SLOTS(xhci_readl(xhci, &xhci->cap_regs->hcs_params1)); + xhci_dbg(xhci, "// xHC can handle at most %d device slots.\n", + (unsigned int) val); + val2 = xhci_readl(xhci, &xhci->op_regs->config_reg); + val |= (val2 & ~HCS_SLOTS_MASK); + xhci_dbg(xhci, "// Setting Max device slots reg = 0x%x.\n", + (unsigned int) val); + xhci_writel(xhci, val, &xhci->op_regs->config_reg); + + xhci->ir_set = &xhci->run_regs->ir_set[0]; + + return 0; +fail: + xhci_warn(xhci, "Couldn't initialize memory\n"); + xhci_mem_cleanup(xhci); + return -ENOMEM; +} diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c new file mode 100644 index 00000000000..4015082adf6 --- /dev/null +++ b/drivers/usb/host/xhci-pci.c @@ -0,0 +1,150 @@ +/* + * xHCI host controller driver PCI Bus Glue. + * + * Copyright (C) 2008 Intel Corp. + * + * Author: Sarah Sharp + * Some code borrowed from the Linux EHCI driver. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY + * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software Foundation, + * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/pci.h> + +#include "xhci.h" + +static const char hcd_name[] = "xhci_hcd"; + +/* called after powerup, by probe or system-pm "wakeup" */ +static int xhci_pci_reinit(struct xhci_hcd *xhci, struct pci_dev *pdev) +{ + /* + * TODO: Implement finding debug ports later. + * TODO: see if there are any quirks that need to be added to handle + * new extended capabilities. + */ + + /* PCI Memory-Write-Invalidate cycle support is optional (uncommon) */ + if (!pci_set_mwi(pdev)) + xhci_dbg(xhci, "MWI active\n"); + + xhci_dbg(xhci, "Finished xhci_pci_reinit\n"); + return 0; +} + +/* called during probe() after chip reset completes */ +static int xhci_pci_setup(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + int retval; + + xhci->cap_regs = hcd->regs; + xhci->op_regs = hcd->regs + + HC_LENGTH(xhci_readl(xhci, &xhci->cap_regs->hc_capbase)); + xhci->run_regs = hcd->regs + + (xhci_readl(xhci, &xhci->cap_regs->run_regs_off) & RTSOFF_MASK); + /* Cache read-only capability registers */ + xhci->hcs_params1 = xhci_readl(xhci, &xhci->cap_regs->hcs_params1); + xhci->hcs_params2 = xhci_readl(xhci, &xhci->cap_regs->hcs_params2); + xhci->hcs_params3 = xhci_readl(xhci, &xhci->cap_regs->hcs_params3); + xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hcc_params); + xhci_print_registers(xhci); + + /* Make sure the HC is halted. */ + retval = xhci_halt(xhci); + if (retval) + return retval; + + xhci_dbg(xhci, "Resetting HCD\n"); + /* Reset the internal HC memory state and registers. */ + retval = xhci_reset(xhci); + if (retval) + return retval; + xhci_dbg(xhci, "Reset complete\n"); + + xhci_dbg(xhci, "Calling HCD init\n"); + /* Initialize HCD and host controller data structures. */ + retval = xhci_init(hcd); + if (retval) + return retval; + xhci_dbg(xhci, "Called HCD init\n"); + + pci_read_config_byte(pdev, XHCI_SBRN_OFFSET, &xhci->sbrn); + xhci_dbg(xhci, "Got SBRN %u\n", (unsigned int) xhci->sbrn); + + /* Find any debug ports */ + return xhci_pci_reinit(xhci, pdev); +} + +static const struct hc_driver xhci_pci_hc_driver = { + .description = hcd_name, + .product_desc = "xHCI Host Controller", + .hcd_priv_size = sizeof(struct xhci_hcd), + + /* + * generic hardware linkage + */ + .flags = HCD_MEMORY | HCD_USB3, + + /* + * basic lifecycle operations + */ + .reset = xhci_pci_setup, + .start = xhci_run, + /* suspend and resume implemented later */ + .stop = xhci_stop, + .shutdown = xhci_shutdown, + + /* + * scheduling support + */ + .get_frame_number = xhci_get_frame, + + /* Implement root hub support later. */ +}; + +/*-------------------------------------------------------------------------*/ + +/* PCI driver selection metadata; PCI hotplugging uses this */ +static const struct pci_device_id pci_ids[] = { { + /* handle any USB 3.0 xHCI controller */ + PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_XHCI, ~0), + .driver_data = (unsigned long) &xhci_pci_hc_driver, + }, + { /* end: all zeroes */ } +}; +MODULE_DEVICE_TABLE(pci, pci_ids); + +/* pci driver glue; this is a "new style" PCI driver module */ +static struct pci_driver xhci_pci_driver = { + .name = (char *) hcd_name, + .id_table = pci_ids, + + .probe = usb_hcd_pci_probe, + .remove = usb_hcd_pci_remove, + /* suspend and resume implemented later */ + + .shutdown = usb_hcd_pci_shutdown, +}; + +int xhci_register_pci() +{ + return pci_register_driver(&xhci_pci_driver); +} + +void xhci_unregister_pci() +{ + pci_unregister_driver(&xhci_pci_driver); +} diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index a4d44aad069..59fae2e5ea5 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -32,6 +32,9 @@ /* xHCI PCI Configuration Registers */ #define XHCI_SBRN_OFFSET (0x60) +/* Max number of USB devices for any host controller - limit in section 6.1 */ +#define MAX_HC_SLOTS 256 + /* * xHCI register interface. * This corresponds to the eXtensible Host Controller Interface (xHCI) @@ -359,10 +362,35 @@ struct intr_reg { u32 erst_dequeue[2]; } __attribute__ ((packed)); +/* irq_pending bitmasks */ #define ER_IRQ_PENDING(p) ((p) & 0x1) -#define ER_IRQ_ENABLE(p) ((p) | 0x2) +/* bits 2:31 need to be preserved */ +#define ER_IRQ_CLEAR(p) ((p) & 0xfffffffe) +#define ER_IRQ_ENABLE(p) ((ER_IRQ_CLEAR(p)) | 0x2) +#define ER_IRQ_DISABLE(p) ((ER_IRQ_CLEAR(p)) & ~(0x2)) + +/* irq_control bitmasks */ +/* Minimum interval between interrupts (in 250ns intervals). The interval + * between interrupts will be longer if there are no events on the event ring. + * Default is 4000 (1 ms). + */ +#define ER_IRQ_INTERVAL_MASK (0xffff) +/* Counter used to count down the time to the next interrupt - HW use only */ +#define ER_IRQ_COUNTER_MASK (0xffff << 16) + +/* erst_size bitmasks */ /* Preserve bits 16:31 of erst_size */ -#define ERST_SIZE_MASK (0xffff<<16) +#define ERST_SIZE_MASK (0xffff << 16) + +/* erst_dequeue bitmasks */ +/* Dequeue ERST Segment Index (DESI) - Segment number (or alias) + * where the current dequeue pointer lies. This is an optional HW hint. + */ +#define ERST_DESI_MASK (0x7) +/* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by + * a work queue (or delayed service routine)? + */ +#define ERST_EHB (1 << 3) /** * struct xhci_run_regs @@ -386,6 +414,8 @@ struct xhci_hcd { struct xhci_cap_regs __iomem *cap_regs; struct xhci_op_regs __iomem *op_regs; struct xhci_run_regs __iomem *run_regs; + /* Our HCD's current interrupter register set */ + struct intr_reg __iomem *ir_set; /* Cached register copies of read-only HC data */ __u32 hcs_params1; @@ -404,7 +434,13 @@ struct xhci_hcd { u8 isoc_threshold; int event_ring_max; int addr_64; + /* 4KB min, 128MB max */ int page_size; + /* Valid values are 12 to 20, inclusive */ + int page_shift; + /* only one MSI vector for now, but might need more later */ + int msix_count; + struct msix_entry *msix_entries; }; /* convert between an HCD pointer and the corresponding EHCI_HCD */ @@ -449,4 +485,27 @@ static inline void xhci_writel(const struct xhci_hcd *xhci, writel(val, regs); } +/* xHCI debugging */ +void xhci_print_ir_set(struct xhci_hcd *xhci, struct intr_reg *ir_set, int set_num); +void xhci_print_registers(struct xhci_hcd *xhci); + +/* xHCI memory managment */ +void xhci_mem_cleanup(struct xhci_hcd *xhci); +int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags); + +#ifdef CONFIG_PCI +/* xHCI PCI glue */ +int xhci_register_pci(void); +void xhci_unregister_pci(void); +#endif + +/* xHCI host controller glue */ +int xhci_halt(struct xhci_hcd *xhci); +int xhci_reset(struct xhci_hcd *xhci); +int xhci_init(struct usb_hcd *hcd); +int xhci_run(struct usb_hcd *hcd); +void xhci_stop(struct usb_hcd *hcd); +void xhci_shutdown(struct usb_hcd *hcd); +int xhci_get_frame(struct usb_hcd *hcd); + #endif /* __LINUX_XHCI_HCD_H */ |