diff options
Diffstat (limited to 'include/asm-cris/etraxgpio.h')
-rw-r--r-- | include/asm-cris/etraxgpio.h | 179 |
1 files changed, 0 insertions, 179 deletions
diff --git a/include/asm-cris/etraxgpio.h b/include/asm-cris/etraxgpio.h deleted file mode 100644 index 38f1c8e1770..00000000000 --- a/include/asm-cris/etraxgpio.h +++ /dev/null @@ -1,179 +0,0 @@ -/* - * The following devices are accessable using this driver using - * GPIO_MAJOR (120) and a couple of minor numbers. - * - * For ETRAX 100LX (CONFIG_ETRAX_ARCH_V10): - * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction - * /dev/gpiob minor 1, 8 bit GPIO, each bit can change direction - * /dev/leds minor 2, Access to leds depending on kernelconfig - * /dev/gpiog minor 3 - * g0dir, g8_15dir, g16_23dir, g24 dir configurable in R_GEN_CONFIG - * g1-g7 and g25-g31 is both input and outputs but on different pins - * Also note that some bits change pins depending on what interfaces - * are enabled. - * - * For ETRAX FS (CONFIG_ETRAXFS): - * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction - * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction - * /dev/gpioc minor 3, 18 bit GPIO, each bit can change direction - * /dev/gpiod minor 4, 18 bit GPIO, each bit can change direction - * /dev/gpioe minor 5, 18 bit GPIO, each bit can change direction - * /dev/leds minor 2, Access to leds depending on kernelconfig - * - * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3): - * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction - * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction - * /dev/gpioc minor 3, 18 bit GPIO, each bit can change direction - * /dev/gpiod minor 4, 18 bit GPIO, each bit can change direction - * /dev/leds minor 2, Access to leds depending on kernelconfig - * /dev/pwm0 minor 16, PWM channel 0 on PA30 - * /dev/pwm1 minor 17, PWM channel 1 on PA31 - * /dev/pwm2 minor 18, PWM channel 2 on PB26 - * - */ -#ifndef _ASM_ETRAXGPIO_H -#define _ASM_ETRAXGPIO_H - -/* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */ -#ifdef CONFIG_ETRAX_ARCH_V10 -#define ETRAXGPIO_IOCTYPE 43 -#define GPIO_MINOR_A 0 -#define GPIO_MINOR_B 1 -#define GPIO_MINOR_LEDS 2 -#define GPIO_MINOR_G 3 -#define GPIO_MINOR_LAST 3 -#endif - -#ifdef CONFIG_ETRAXFS -#define ETRAXGPIO_IOCTYPE 43 -#define GPIO_MINOR_A 0 -#define GPIO_MINOR_B 1 -#define GPIO_MINOR_LEDS 2 -#define GPIO_MINOR_C 3 -#define GPIO_MINOR_D 4 -#define GPIO_MINOR_E 5 -#ifdef CONFIG_ETRAX_VIRTUAL_GPIO -#define GPIO_MINOR_V 6 -#define GPIO_MINOR_LAST 6 -#else -#define GPIO_MINOR_LAST 5 -#endif -#endif - -#ifdef CONFIG_CRIS_MACH_ARTPEC3 -#define ETRAXGPIO_IOCTYPE 43 -#define GPIO_MINOR_A 0 -#define GPIO_MINOR_B 1 -#define GPIO_MINOR_LEDS 2 -#define GPIO_MINOR_C 3 -#define GPIO_MINOR_D 4 -#ifdef CONFIG_ETRAX_VIRTUAL_GPIO -#define GPIO_MINOR_V 6 -#define GPIO_MINOR_LAST 6 -#else -#define GPIO_MINOR_LAST 4 -#endif -#define GPIO_MINOR_PWM0 16 -#define GPIO_MINOR_PWM1 17 -#define GPIO_MINOR_PWM2 18 -#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PWM2 -#endif - -/* supported ioctl _IOC_NR's */ - -#define IO_READBITS 0x1 /* read and return current port bits (obsolete) */ -#define IO_SETBITS 0x2 /* set the bits marked by 1 in the argument */ -#define IO_CLRBITS 0x3 /* clear the bits marked by 1 in the argument */ - -/* the alarm is waited for by select() */ - -#define IO_HIGHALARM 0x4 /* set alarm on high for bits marked by 1 */ -#define IO_LOWALARM 0x5 /* set alarm on low for bits marked by 1 */ -#define IO_CLRALARM 0x6 /* clear alarm for bits marked by 1 */ - -/* LED ioctl */ -#define IO_LEDACTIVE_SET 0x7 /* set active led - * 0=off, 1=green, 2=red, 3=yellow */ - -/* GPIO direction ioctl's */ -#define IO_READDIR 0x8 /* Read direction 0=input 1=output (obsolete) */ -#define IO_SETINPUT 0x9 /* Set direction for bits set, 0=unchanged 1=input, - returns mask with current inputs (obsolete) */ -#define IO_SETOUTPUT 0xA /* Set direction for bits set, 0=unchanged 1=output, - returns mask with current outputs (obsolete)*/ - -/* LED ioctl extended */ -#define IO_LED_SETBIT 0xB -#define IO_LED_CLRBIT 0xC - -/* SHUTDOWN ioctl */ -#define IO_SHUTDOWN 0xD -#define IO_GET_PWR_BT 0xE - -/* Bit toggling in driver settings */ -/* bit set in low byte0 is CLK mask (0x00FF), - bit set in byte1 is DATA mask (0xFF00) - msb, data_mask[7:0] , clk_mask[7:0] - */ -#define IO_CFG_WRITE_MODE 0xF -#define IO_CFG_WRITE_MODE_VALUE(msb, data_mask, clk_mask) \ - ( (((msb)&1) << 16) | (((data_mask) &0xFF) << 8) | ((clk_mask) & 0xFF) ) - -/* The following 4 ioctl's take a pointer as argument and handles - * 32 bit ports (port G) properly. - * These replaces IO_READBITS,IO_SETINPUT AND IO_SETOUTPUT - */ -#define IO_READ_INBITS 0x10 /* *arg is result of reading the input pins */ -#define IO_READ_OUTBITS 0x11 /* *arg is result of reading the output shadow */ -#define IO_SETGET_INPUT 0x12 /* bits set in *arg is set to input, - * *arg updated with current input pins. - */ -#define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, - * *arg updated with current output pins. - */ - -/* The following ioctl's are applicable to the PWM channels only */ - -#define IO_PWM_SET_MODE 0x20 - -enum io_pwm_mode { - PWM_OFF = 0, /* disabled, deallocated */ - PWM_STANDARD = 1, /* 390 kHz, duty cycle 0..255/256 */ - PWM_FAST = 2, /* variable freq, w/ 10ns active pulse len */ - PWM_VARFREQ = 3 /* individually configurable high/low periods */ -}; - -struct io_pwm_set_mode { - enum io_pwm_mode mode; -}; - -/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns - * from 10ns (value = 0) to 81920ns (value = 8191) - * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to - * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty - * cycle (81920 + 10ns or 10ns + 81920ns, respectively).) - */ -#define IO_PWM_SET_PERIOD 0x21 - -struct io_pwm_set_period { - unsigned int lo; /* 0..8191 */ - unsigned int hi; /* 0..8191 */ -}; - -/* Only for modes PWM_STANDARD and PWM_FAST. - * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from - * 0 (value = 0) to 255/256 (value = 255). - * For PWM_FAST, set duty cycle of PWM output signal from - * 0% (value = 0) to 100% (value = 255). Output signal in this mode - * is a 10ns pulse surrounded by a high or low level depending on duty - * cycle (except for 0% and 100% which result in a constant output). - * Resulting output frequency varies from 50 MHz at 50% duty cycle, - * down to 390 kHz at min/max duty cycle. - */ -#define IO_PWM_SET_DUTY 0x22 - -struct io_pwm_set_duty { - int duty; /* 0..255 */ -}; - -#endif |