| Age | Commit message (Collapse) | Author |
|---|
|
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The device id for Am29DL800BB in jedec_probe.c is wrong.
Reference: http://www.spansion.com/datasheets/21519c4.pdf
I discovered this while working with u-boot.
The u-boot folks mentioned Linux as an upstream reference, thought I'd
post a heads-up here too.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The unlock_addr rework in kernel 2.6.25 breaks 16-bit SST chips. SST
39LF160 and SST 39VF1601 are both 16-bit only chip (do not have BYTE#
pin) and new uaddr value is not correct for them. Add
MTD_UADDR_0xAAAA_0x5555 for those chips. Tested with SST 39VF1601
chip.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch add support for non-CFI Eon EN29SL800B[BT] NOR flash chips.
The Eon chips have manufacturer ID in the first bank, therefore this patch
depends on support for flash chips with ID in bank other than 0.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
According to JEDEC "Standard Manufacturer's Identification Code"
(http://www.jedec.org/download/search/jep106W.pdf)
several first banks of NOR flash can contain 0x7f instead of actual ID.
This patch adds support for reading manufacturer ID from banks other than 0.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support for M50FLW080A and M50FLW080B revisions of LPC flash
devices.
Signed-off-by: Aaron Lindner <alindner@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support for the SST 36VF3203 flash chip. It is used on Emerson
KSI8560 board.
Signed-off-by: Andrei Dolnikov <adolnikov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support for the ST M29W400DB flash chip. which is used on the GLAN Tank
NAS.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
$ codiff $OBJ.old $OBJ
drivers/mtd/chips/jedec_probe.c:
cfi_jedec_setup | -320
jedec_probe_chip | -7073
2 functions changed, 7393 bytes removed, diff: -7393
drivers/mtd/chips/jedec_probe.c:
jedec_reset | +1151
1 function changed, 1151 bytes added, diff: +1151
drivers/mtd/chips/jedec_probe.o:
3 functions changed, 1151 bytes added, 7393 bytes removed, diff: -6242
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Use a single unlock address, adjust it for the device type in the
knowledge that it'll be adjusted back again. This has the desirable
effect of masking out the least significant bit of the address for x16
devices.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Having laid the code out so that it's easier to read instead of sticking
to the 80-column guideline even when it doesn't make sense, a bug is
immediately spotted... we were only checking _one_ of the unlock
addresses to see if it runs off the end of the map.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This should have no functional effects -- we've been ignoring all but
the first address in the array for a long time, and using it only to
indicate which device types are supported.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support for the SST 39VF1601 flash chip.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch cleans up duplicate includes in
drivers/mtd/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add descriptions for Fujitsu MBM29F800BA and ST M29F800AB flash chips.
Those chips are compatible (except for the ids) with the AMD AM29F800BB.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add chip driver and JEDEC probe support for the SST 49LF040B flash chip.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This adds flash chip used in Sharp Zaurus sl5500 (collie) to jedec_probe.
Values work for read-only access, but I have not figured out how to do
read-write.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The change to the generic probe to look for the
smallest width of chip first is causing some problems
on boards with a single 16bit device.
The problem seems to be the jedec_match() is truncating
the device-id read from the table to match against the
one read from the hardware, causing a match against the
partial id of some chips with 16bit IDs (such as the
SST39LF160)
This fixes things for my own board, but something may
need to be done if the same problem is exhibited for
chips with an 8bit ID
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
