| Age | Commit message (Collapse) | Author |
|---|
|
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Stash the first platform string matched by identify_cpu() in
powerpc_base_platform, and supply that to the ELF loader for the value
of AT_BASE_PLATFORM.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Background from Maynard Johnson:
As of POWER6, a set of 32 common events is defined that must be
supported on all future POWER processors. The main impetus for this
compat set is the need to support partition migration, especially from
processor P(n) to processor P(n+1), where performance software that's
running in the new partition may not be knowledgeable about processor
P(n+1). If a performance tool determines it does not support the
physical processor, but is told (via the
PPC_FEATURE_PSERIES_PERFMON_COMPAT bit) that the processor supports
the notion of the PMU compat set, then the performance tool can
surface just those events to the user of the tool.
PPC_FEATURE_PSERIES_PERFMON_COMPAT indicates that the PMU supports at
least this basic subset of events which is compatible across POWER
processor lines.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add the CPU feature bit for the new Strong Access Ordering
facility of Power7
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
To allow for a single kernel image on e500 v1/v2/mc we need to fixup lwsync
at runtime. On e500v1/v2 lwsync causes an illop so we need to patch up
the code. We default to 'sync' since that is always safe and if the cpu
is capable we will replace 'sync' with 'lwsync'.
We introduce CPU_FTR_LWSYNC as a way to determine at runtime if this is
needed. This flag could be moved elsewhere since we dont really use it
for the normal CPU_FTR purpose.
Finally we only store the relative offset in the fixup section to keep it
as small as possible rather than using a full fixup_entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a VSX CPU feature. Also add code to detect if VSX is available
from the device tree.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The CPU and firmware feature fixup macros are currently spread across
three files, firmware.h, cputable.h and asm-compat.h. Consolidate them
into their own file, feature-fixups.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
asm/asm-compat.h doesn't seem to be intended for userspace usage.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a cputable entry for the POWER7 processor.
Also tell firmware that we know about POWER7.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If we have an L2CSR register (e500mc) we need to flush the L2 before going
to nap. We use the HW flush mechanism provided in that register.
The code reuses the CPU_FTR_604_PERF_MON bit as it is no longer used by
any code in the kernel. Additionally we didn't reuse the exist L2CR
feature bit as this is intended for the 7xxx L2CR register and L2CSR
is part of the new Freescale "Book-E" registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The e500 core enter DOZE/NAP power-saving modes when the core go to
cpu_idle routine.
The power management default running mode is DOZE, If the user
echo 1 > /proc/sys/kernel/powersave-nap
the system will change to NAP running mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The new e500mc core from Freescale is based on the e500v2 but with the
following changes:
* Supports only the Enhanced Debug Architecture (DSRR0/1, etc)
* Floating Point
* No SPE
* Supports lwsync
* Doorbell Exceptions
* Hypervisor
* Cache line size is now 64-bytes (e500v1/v2 have a 32-byte cache line)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some of the more recent e300 cores have the same performance monitor
implementation as the e500. e300 isn't book-e, so the name isn't
really appropriate. In preparation for e300 support, rename a bunch
of fsl_booke things to say fsl_emb (Freescale Embedded Performance Monitors).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.
This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
The context switch code in the kernel issues a dummy stwcx. to clear the
reservation, as recommended by the architecture. However, some processors
can have issues if this stwcx to address A occurs while the reservation
is already held to a different address B. To avoid this problem, the dummy
stwcx. needs to be paired with a dummy lwarx to the same address.
This adds the dummy lwarx, and creates a cpu feature bit to indicate
which cpus are affected. Tested on mpc8641_hpcn_defconfig in
arch/powerpc; build tested in arch/ppc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
PA6T has a bug where the slbie instruction does not honor the large
segment bit. As a result, we have to always use slbia when switching
context.
We don't have to worry about changing the slbie's during fault processing,
since they should never be replacing one VSID with another using the
same ESID. I.e. there's no risk for inserting duplicate entries due to a
failed slbie of the old entry. So as long as we clear it out on context
switch we should be fine.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This makes the kernel use 1TB segments for all kernel mappings and for
user addresses of 1TB and above, on machines which support them
(currently POWER5+, POWER6 and PA6T).
We detect that the machine supports 1TB segments by looking at the
ibm,processor-segment-sizes property in the device tree.
We don't currently use 1TB segments for user addresses < 1T, since
that would effectively prevent 32-bit processes from using huge pages
unless we also had a way to revert to using 256MB segments. That
would be possible but would involve extra complications (such as
keeping track of which segment size was used when HPTEs were inserted)
and is not addressed here.
Parts of this patch were originally written by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Some IBM machines supply a "logical" PVR (processor version register)
value in the device tree in the cpu nodes rather than the real PVR.
This is used for instance to indicate that the processors in a POWER6
partition have been configured by the hypervisor to run in POWER5+
mode rather than POWER6 mode. To cope with this, we call identify_cpu
a second time with the logical PVR value (the first call is with the
real PVR value in the very early setup code).
However, POWER5+ machines can also supply a logical PVR value, and use
the same value (the value that indicates a v2.04 architecture
compliant processor). This causes problems for code that uses the
performance monitor (such as oprofile), because the PMU registers are
different in POWER6 (even in POWER5+ mode) from the real POWER5+.
This change works around this problem by taking out the PMU
information from the cputable entries for the logical PVR values, and
changing identify_cpu so that the second call to it won't overwrite
the PMU information that was established by the first call (the one
with the real PVR), but does update the other fields. Specifically,
if the cputable entry for the logical PVR value has num_pmcs == 0,
none of the PMU-related fields get used.
So that we can create a mixed cputable entry, we now make cur_cpu_spec
point to a single static struct cpu_spec, and copy stuff from
cpu_specs[i] into it. This has the side-effect that we can now make
cpu_specs[] be initdata.
Ultimately it would be good to move the PMU-related fields out to a
separate structure, pointed to by the cputable entries, and change
identify_cpu so that it saves the PMU info pointer, copies the whole
structure, and restores the PMU info pointer, rather than identify_cpu
having to list all the fields that are *not* PMU-related.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The 8272 (and presumably other PCI PQ2 chips) appear to have the
same issue as the 83xx regarding PCI streaming DMA.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Make it so that SPE support can be determined at runtime. This is similiar
to how we handle AltiVec. This allows us to have SPE support built in and
work on processors with and without SPE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The 750 CPU_FTR macros have quite a bit of duplication in them. Consolidate
them to use CPU_FTRS_750 and only list the unique features for derivatives.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially). It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.
In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).
This tries to clarify the situation a little. The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified. We check this, instead of
SPLIT_ID_CACHE nearly everywhere.
The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200. In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature. The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.
This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove CPU_FTR_NEED_COHERENT for MPC7448 (and single-core MPC86xx).
This prevents needlessly setting M=1 when not SMP.
Signed-off-by: James.Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Oprofile support for PA6T, kernel side.
Also rename the PA6T_SPRN.* defines to SPRN_PA6T.*.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
PowerPC 750CL has high BATs. The patch below adds a CPU_FTRS_750CL that
includes that. Without it, the original firmware mappings in the high BATs
aren't cleared which continue to override the linux translations.
It also adds CPU_FTR_COMMON to CPU_FTRS_750GX for completeness.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add cputable entries for which type of PMC implementation the processor
has.
I've only filled in the current 64-bit processors, the unfilled default
value will have same behaviour as before so it can be done over time
as needed.
Also tidy up the dummy_perf implementation a bit, aggregating it into
one function with ifdefs instead of several.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
CPU_FTRS_POWER6X is unused, hence remove it.
Signed-off-by Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
|
|
POWER6 adds a new SPR, the data stream control register (DSCR). It can
be used to adjust how agressive the prefetch mechanisms are.
Its possible we may want to context switch this, but for now just export
it to userspace via sysfs so we can adjust it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The e300c2 has no FPU. Its MSR[FP] is grounded to zero. If an attempt
is made to execute a floating point instruction (including floating-point
load, store, or move instructions), the e300c2 takes a floating-point
unavailable interrupt.
This patch adds support for FP emulation on the e300c2 by declaring a
new CPU_FTR_FP_TAKES_FPUNAVAIL, where FP unavail interrupts are
intercepted and redirected to the ProgramCheck exception path for
correct emulation handling.
(If we run out of CPU_FTR bits we could look to reclaim this bit by adding
support to test the cpu_user_features for PPC_FEATURE_HAS_FPU instead)
It adds a nop to the exception path for 32-bit processors with a FPU.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Remove CPU_FTR_16M_PAGE from the cupfeatures mask at runtime on iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
It saves #ifdef'ing in callers if we at least define the 64-bit cpu
features for 32-bit also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The Cell CPU timebase has an erratum. When reading the entire 64 bits
of the timebase with one mftb instruction, there is a handful of cycles
window during which one might read a value with the low order 32 bits
already reset to 0x00000000 but the high order bits not yet incremeted
by one. This fixes it by reading the timebase again until the low order
32 bits is no longer 0. That might introduce occasional latencies if
hitting mftb just at the wrong time, but no more than 70ns on a cell
blade, and that was considered acceptable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch reworks the feature fixup mecanism so vdso's can be fixed up.
The main issue was that the construct:
.long label (or .llong on 64 bits)
will not work in the case of a shared library like the vdso. It will
generate an empty placeholder in the fixup table along with a reloc,
which is not something we can deal with in the vdso.
The idea here (thanks Alan Modra !) is to instead use something like:
1:
.long label - 1b
That is, the feature fixup tables no longer contain addresses of bits of
code to patch, but offsets of such code from the fixup table entry
itself. That is properly resolved by ld when building the .so's. I've
modified the fixup mecanism generically to use that method for the rest
of the kernel as well.
Another trick is that the 32 bits vDSO included in the 64 bits kernel
need to have a table in the 64 bits format. However, gas does not
support 32 bits code with a statement of the form:
.llong label - 1b (Or even just .llong label)
That is, it cannot emit the right fixup/relocation for the linker to use
to assign a 32 bits address to an .llong field. Thus, in the specific
case of the 32 bits vdso built as part of the 64 bits kernel, we are
using a modified macro that generates:
.long 0xffffffff
.llong label - 1b
Note that is assumes that the value is negative which is enforced by
the .lds (those offsets are always negative as the .text is always
before the fixup table and gas doesn't support emiting the reloc the
other way around).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch adds some macros that can be used with an explicit label in
order to nest cpu features. This should be used very careful but is
necessary for the upcoming cell TB fixup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
There are currently two versions of the functions for applying the
feature fixups, one for CPU features and one for firmware features. In
addition, they are both in assembly and with separate implementations
for 32 and 64 bits. identify_cpu() is also implemented in assembly and
separately for 32 and 64 bits.
This patch replaces them with a pair of C functions. The call sites are
slightly moved on ppc64 as well to be called from C instead of from
assembly, though it's a very small change, and thus shouldn't cause any
problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Introduce PWRficient PA6T cputable entries and feature bits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The performance monitor implementation (including CTRL register behaviour)
is just included in PPC v2 as an example, it's not truly part of the base.
It's actually a somewhat misleading feature, but I'll leave that be for
now: The presence of the register is not what the feature bit is used
for, but instead it's used to determine if it contains the runlatch
bit for idle reporting of the performance monitor. For alternative
implementations, the register might still exist but the bit might have
different meaning (or no meaning at all).
For now, split it off and don't include it in CPU_FTR_PPCAS_ARCH_V2_BASE.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Cleanup CPU inits a bit more, Geoff Levand already did some earlier.
* Move CPU state save to cpu_setup, since cpu_setup is only ever done
on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
function pointers to the cputable to use instead. Powermac always
has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
everyone but powermac and iSeries use it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
|
|
Reflect the fact that the Cell Broadband Engine supports 64k
pages by adding the bit to the CPU features.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove some stale POWER3/POWER4/970 on 32bit kernel support.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This adds the PowerPC part of the code to allow processes to change
their endian mode via prctl.
This also extends the alignment exception handler to be able to fix up
alignment exceptions that occur in little-endian mode, both for
"PowerPC" little-endian and true little-endian.
We always enter signal handlers in big-endian mode -- the support for
little-endian mode does not amount to the creation of a little-endian
user/kernel ABI. If the signal handler returns, the endian mode is
restored to what it was when the signal was delivered.
We have two new kernel CPU feature bits, one for PPC little-endian and
one for true little-endian. Most of the classic 32-bit processors
support PPC little-endian, and this is reflected in the CPU feature
table. There are two corresponding feature bits reported to userland
in the AT_HWCAP aux vector entry.
This is based on an earlier patch by Anton Blanchard.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
POWER6 moves some of the MMCRA bits and also requires some bits to be
cleared each PMU interrupt.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a cputable entry for the POWER6 processor.
The SIHV and SIPR bits in the mmcra have moved in POWER6, so disable
support for that until oprofile is fixed.
Also tell firmware that we know about POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Christoph noticed that sparse warned about all the enum tags in cuptable.h
that had values that required them to be type log. (enum tags are ints
according to the standard.)
This patch attempts to fix them in the least intrusive way possible by
turning them all into #defines except for the 32 bit CPU_FTRS_POSSIBLE and
CPU_FTRS_ALWAYS which are hard to construct that way. This works because
these last two contain no bits above 2^31.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove redundant whitespace in include/asm-powerpc/cputable.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
