aboutsummaryrefslogtreecommitdiff
path: root/Documentation/driver-model/platform.txt
blob: 19c4a6e136760750365483d49751edb4853daad6 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
Platform Devices and Drivers
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
See <linux/platform_device.h> for the driver model interface to the
platform bus:  platform_device, and platform_driver.  This pseudo-bus
is used to connect devices on busses with minimal infrastructure,
like those used to integrate peripherals on many system-on-chip
processors, or some "legacy" PC interconnects; as opposed to large
formally specified ones like PCI or USB.


Platform devices
~~~~~~~~~~~~~~~~
Platform devices are devices that typically appear as autonomous
entities in the system. This includes legacy port-based devices and
host bridges to peripheral buses, and most controllers integrated
into system-on-chip platforms.  What they usually have in common
is direct addressing from a CPU bus.  Rarely, a platform_device will
be connected through a segment of some other kind of bus; but its
registers will still be directly addressable.

Platform devices are given a name, used in driver binding, and a
list of resources such as addresses and IRQs.

struct platform_device {
	const char	*name;
	u32		id;
	struct device	dev;
	u32		num_resources;
	struct resource	*resource;
};


Platform drivers
~~~~~~~~~~~~~~~~
Platform drivers follow the standard driver model convention, where
discovery/enumeration is handled outside the drivers, and drivers
provide probe() and remove() methods.  They support power management
and shutdown notifications using the standard conventions.

struct platform_driver {
	int (*probe)(struct platform_device *);
	int (*remove)(struct platform_device *);
	void (*shutdown)(struct platform_device *);
	int (*suspend)(struct platform_device *, pm_message_t state);
	int (*suspend_late)(struct platform_device *, pm_message_t state);
	int (*resume_early)(struct platform_device *);
	int (*resume)(struct platform_device *);
	struct device_driver driver;
};

Note that probe() should general verify that the specified device hardware
actually exists; sometimes platform setup code can't be sure.  The probing
can use device resources, including clocks, and device platform_data.

Platform drivers register themselves the normal way:

	int platform_driver_register(struct platform_driver *drv);

Or, in common situations where the device is known not to be hot-pluggable,
the probe() routine can live in an init section to reduce the driver's
runtime memory footprint:

	int platform_driver_probe(struct platform_driver *drv,
			  int (*probe)(struct platform_device *))


Device Enumeration
~~~~~~~~~~~~~~~~~~
As a rule, platform specific (and often board-specific) setup code will
register platform devices:

	int platform_device_register(struct platform_device *pdev);

	int platform_add_devices(struct platform_device **pdevs, int ndev);

The general rule is to register only those devices that actually exist,
but in some cases extra devices might be registered.  For example, a kernel
might be configured to work with an external network adapter that might not
be populated on all boards, or likewise to work with an integrated controller
that some boards might not hook up to any peripherals.

In some cases, boot firmware will export tables describing the devices
that are populated on a given board.   Without such tables, often the
only way for system setup code to set up the correct devices is to build
a kernel for a specific target board.  Such board-specific kernels are
common with embedded and custom systems development.

In many cases, the memory and IRQ resources associated with the platform
device are not enough to let the device's driver work.  Board setup code
will often provide additional information using the device's platform_data
field to hold additional information.

Embedded systems frequently need one or more clocks for platform devices,
which are normally kept off until they're actively needed (to save power).
System setup also associates those clocks with the device, so that that
calls to clk_get(&pdev->dev, clock_name) return them as needed.


Device Naming and Driver Binding
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The platform_device.dev.bus_id is the canonical name for the devices.
It's built from two components:

    * platform_device.name ... which is also used to for driver matching.

    * platform_device.id ... the device instance number, or else "-1"
      to indicate there's only one.

These are concatenated, so name/id "serial"/0 indicates bus_id "serial.0", and
"serial/3" indicates bus_id "serial.3"; both would use the platform_driver
named "serial".  While "my_rtc"/-1 would be bus_id "my_rtc" (no instance id)
and use the platform_driver called "my_rtc".

Driver binding is performed automatically by the driver core, invoking
driver probe() after finding a match between device and driver.  If the
probe() succeeds, the driver and device are bound as usual.  There are
three different ways to find such a match:

    - Whenever a device is registered, the drivers for that bus are
      checked for matches.  Platform devices should be registered very
      early during system boot.

    - When a driver is registered using platform_driver_register(), all
      unbound devices on that bus are checked for matches.  Drivers
      usually register later during booting, or by module loading.

    - Registering a driver using platform_driver_probe() works just like
      using platform_driver_register(), except that the driver won't
      be probed later if another device registers.  (Which is OK, since
      this interface is only for use with non-hotpluggable devices.)