aboutsummaryrefslogtreecommitdiff
path: root/arch/ppc/boot/simple/pci.c
blob: b0f673c8b7d96c60461d8c5f201bc378541fd2fb (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
/* Stand alone funtions for QSpan Tundra support.
 */
#include <linux/types.h>
#include <linux/pci.h>
#include <asm/mpc8xx.h>

extern void puthex(unsigned long val);
extern void puts(const char *);

/* To map PCI devices, you first write 0xffffffff into the device
 * base address registers.  When the register is read back, the
 * number of most significant '1' bits describes the amount of address
 * space needed for mapping.  If the most significant bit is not set,
 * either the device does not use that address register, or it has
 * a fixed address that we can't change.  After the address is assigned,
 * the command register has to be written to enable the card.
 */
typedef struct {
	u_char	pci_bus;
	u_char	pci_devfn;
	ushort	pci_command;
	uint	pci_addrs[6];
} pci_map_t;

/* We should probably dynamically allocate these structures.
*/
#define MAX_PCI_DEVS	32
int	pci_dev_cnt;
pci_map_t	pci_map[MAX_PCI_DEVS];

void pci_conf_write(int bus, int device, int func, int reg, uint writeval);
void pci_conf_read(int bus, int device, int func, int reg, void *readval);
void probe_addresses(int bus, int devfn);
void map_pci_addrs(void);

extern int
qs_pci_read_config_byte(unsigned char bus, unsigned char dev_fn,
			unsigned char offset, unsigned char *val);
extern int
qs_pci_read_config_word(unsigned char bus, unsigned char dev_fn,
			unsigned char offset, unsigned short *val);
extern int
qs_pci_read_config_dword(unsigned char bus, unsigned char dev_fn,
			 unsigned char offset, unsigned int *val);
extern int
qs_pci_write_config_byte(unsigned char bus, unsigned char dev_fn,
			 unsigned char offset, unsigned char val);
extern int
qs_pci_write_config_word(unsigned char bus, unsigned char dev_fn,
			 unsigned char offset, unsigned short val);
extern int
qs_pci_write_config_dword(unsigned char bus, unsigned char dev_fn,
			  unsigned char offset, unsigned int val);


/* This is a really stripped version of PCI bus scan.  All we are
 * looking for are devices that exist.
 */
void
pci_scanner(int addr_probe)
{
	unsigned int devfn, l, class, bus_number;
	unsigned char hdr_type, is_multi;

	is_multi = 0;
	bus_number = 0;
	for (devfn = 0; devfn < 0xff; ++devfn) {
		/* The device numbers are comprised of upper 5 bits of
		 * device number and lower 3 bits of multi-function number.
		 */
		if ((devfn & 7) && !is_multi) {
			/* Don't scan multifunction addresses if this is
			 * not a multifunction device.
			 */
			continue;
		}

		/* Read the header to determine card type.
		*/
		qs_pci_read_config_byte(bus_number, devfn, PCI_HEADER_TYPE,
								&hdr_type);

		/* If this is a base device number, check the header to
		 * determine if it is mulifunction.
		 */
		if ((devfn & 7) == 0)
			is_multi = hdr_type & 0x80;

		/* Check to see if the board is really in the slot.
		*/
		qs_pci_read_config_dword(bus_number, devfn, PCI_VENDOR_ID, &l);
		/* some broken boards return 0 if a slot is empty: */
		if (l == 0xffffffff || l == 0x00000000 || l == 0x0000ffff ||
							l == 0xffff0000) {
			/* Nothing there.
			*/
			is_multi = 0;
			continue;
		}

		/* If we are not performing an address probe,
		 * just simply print out some information.
		 */
		if (!addr_probe) {
			qs_pci_read_config_dword(bus_number, devfn,
						PCI_CLASS_REVISION, &class);

			class >>= 8;	    /* upper 3 bytes */

#if 0
			printf("Found (%3d:%d): vendor 0x%04x, device 0x%04x, class 0x%06x\n",
				(devfn >> 3), (devfn & 7),
				(l & 0xffff),  (l >> 16) & 0xffff, class);
#else
			puts("Found ("); puthex(devfn >> 3);
			puts(":"); puthex(devfn & 7);
			puts("): vendor "); puthex(l & 0xffff);
			puts(", device "); puthex((l >> 16) & 0xffff);
			puts(", class "); puthex(class); puts("\n");
#endif
		}
		else {
			/* If this is a "normal" device, build address list.
			*/
			if ((hdr_type & 0x7f) == PCI_HEADER_TYPE_NORMAL)
				probe_addresses(bus_number, devfn);
		}
	}

	/* Now map the boards.
	*/
	if (addr_probe)
		map_pci_addrs();
}

/* Probe addresses for the specified device.  This is a destructive
 * operation because it writes the registers.
 */
void
probe_addresses(bus, devfn)
{
	int	i;
	uint	pciaddr;
	ushort	pcicmd;
	pci_map_t	*pm;

	if (pci_dev_cnt >= MAX_PCI_DEVS) {
		puts("Too many PCI devices\n");
		return;
	}

	pm = &pci_map[pci_dev_cnt++];

	pm->pci_bus = bus;
	pm->pci_devfn = devfn;

	for (i=0; i<6; i++) {
		qs_pci_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_0 + (i * 4), -1);
		qs_pci_read_config_dword(bus, devfn, PCI_BASE_ADDRESS_0 + (i * 4),
								&pciaddr);
		pm->pci_addrs[i] = pciaddr;
		qs_pci_read_config_word(bus, devfn, PCI_COMMAND, &pcicmd);
		pm->pci_command = pcicmd;
	}
}

/* Map the cards into the PCI space.  The PCI has separate memory
 * and I/O spaces.  In addition, some memory devices require mapping
 * below 1M.  The least significant 4 bits of the address register
 * provide information.  If this is an I/O device, only the LS bit
 * is used to indicate that, so I/O devices can be mapped to a two byte
 * boundard.  Memory addresses can be mapped to a 32 byte boundary.
 * The QSpan implementations usually have a 1Gbyte space for each
 * memory and I/O spaces.
 *
 * This isn't a terribly fancy algorithm.  I just map the spaces from
 * the top starting with the largest address space.  When finished,
 * the registers are written and the card enabled.
 *
 * While the Tundra can map a large address space on most boards, we
 * need to be careful because it may overlap other devices (like IMMR).
 */
#define MEMORY_SPACE_SIZE	0x20000000
#define IO_SPACE_SIZE		0x20000000

void
map_pci_addrs()
{
	uint	pci_mem_top, pci_mem_low;
	uint	pci_io_top;
	uint	addr_mask, reg_addr, space;
	int	i, j;
	pci_map_t *pm;

	pci_mem_top = MEMORY_SPACE_SIZE;
	pci_io_top = IO_SPACE_SIZE;
	pci_mem_low = (1 * 1024 * 1024);	/* Below one meg addresses */

	/* We can't map anything more than the maximum space, but test
	 * for it anyway to catch devices out of range.
	 */
	addr_mask = 0x80000000;

	do {
		space = (~addr_mask) + 1;	/* Size of the space */
		for (i=0; i<pci_dev_cnt; i++) {
			pm = &pci_map[i];
			for (j=0; j<6; j++) {
				/* If the MS bit is not set, this has either
				 * already been mapped, or is not used.
				 */
				reg_addr = pm->pci_addrs[j];
				if ((reg_addr & 0x80000000) == 0)
					continue;
				if (reg_addr & PCI_BASE_ADDRESS_SPACE_IO) {
					if ((reg_addr & PCI_BASE_ADDRESS_IO_MASK) != addr_mask)
						continue;
					if (pci_io_top < space) {
						puts("Out of PCI I/O space\n");
					}
					else {
						pci_io_top -= space;
						pm->pci_addrs[j] = pci_io_top;
						pm->pci_command |= PCI_COMMAND_IO;
					}
				}
				else {
					if ((reg_addr & PCI_BASE_ADDRESS_MEM_MASK) != addr_mask)
						continue;

					/* Memory space.  Test if below 1M.
					*/
					if (reg_addr & PCI_BASE_ADDRESS_MEM_TYPE_1M) {
						if (pci_mem_low < space) {
							puts("Out of PCI 1M space\n");
						}
						else {
							pci_mem_low -= space;
							pm->pci_addrs[j] = pci_mem_low;
						}
					}
					else {
						if (pci_mem_top < space) {
							puts("Out of PCI Mem space\n");
						}
						else {
							pci_mem_top -= space;
							pm->pci_addrs[j] = pci_mem_top;
						}
					}
					pm->pci_command |= PCI_COMMAND_MEMORY;
				}
			}
		}
		addr_mask >>= 1;
		addr_mask |= 0x80000000;
	} while (addr_mask != 0xfffffffe);
	
	/* Now, run the list one more time and map everything.
	*/
	for (i=0; i<pci_dev_cnt; i++) {
		pm = &pci_map[i];
		for (j=0; j<6; j++) {
			qs_pci_write_config_dword(pm->pci_bus, pm->pci_devfn,
				PCI_BASE_ADDRESS_0 + (j * 4), pm->pci_addrs[j]);
		}

		/* Enable memory or address mapping.
		*/
		qs_pci_write_config_word(pm->pci_bus, pm->pci_devfn, PCI_COMMAND,
			pm->pci_command);
	}
}